716103
14
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
Two Speed Gear Setting
The drill is fitted with a 2 speed gear system allowing for high and low drilling speeds. To set the speed use the slider switch on the
top of the drill.
Use the low (1) speed for high power and torque applications.
Use the high (2) speed for low power fast drilling applications.
Do not attempt to adjust the speed setting while the drill is in use otherwise the gears will be damaged.
Drilling(Wood and other soft materials)
If drilling in a small workpiece, make sure it is securely held in a vice or clamped to a secure platform such as a bench or table.
Install the correct drill bit in the chuck. Rotate the chuck body to loosen or tighten the drill bit in the chuck. Never use the drill’s
power to rotate the chuck body.
Select the rotation direction to clockwise using the button located above the trigger switch.
Select the correct transmission speed. Use the slower speed for drilling large holes.
Set the torque adjusting collar to the drilling position (Fig.2 (3)).
Slide the fully charged battery pack onto the base of the handle.
Mark the drilling point with a centre punch when drilling in metal to prevent the drill bit from slipping off centre as you begin
drilling.
Place the drill bit at the location of the hole to be drilled and squeeze the trigger. The harder you squeeze, the faster the drill
turns.
Driving Screws
Suggested Torque Settings
1-4 Driving small screws
5-8 Driving medium size screws into soft materials
9-14 Driving screws into soft and medium-density materials
15-21 Driving screws into hardwood
Install the correct screwdriver bit in the chuck. Use the largest bit size that will properly that the screw. Make sure the that
sides of the bit are gripped by the chuck.
Set the transmission speed to low speed.
Set the rotation directions to clockwise.
Set the torque collar desired setting (Fig.1(1))
Place the screwdriver bit into the screw and hold the bit firmly into the screw to prevent slippage and drive a test screw.
After driving a test screw, adjust the torque setting up or down so the screw is driven to the desired depth without being over
driven.
Release the trigger immediately when the torque clutch begins to ‘rattle.
Screws can be removed by reversing the direction of the rotation.
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Blaupunkt BSKA 754103 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Blaupunkt BSKA 754103 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info