388366
7
Verklein
Vergroot
Pagina terug
1/97
Pagina verder
7
ENGLISH
X Charge discharged batteries within 1 week. Battery life
will be greatly diminished if stored in a discharged state.
Charge indicators
If the charger detects a problem with a battery pack, the
charge indicator (11) will flash at a fast rate.
X If this occurs, re-insert the battery pack (9).
X If the problem persists, put a different battery pack in the
charger to determine if the charger is OK.
X If the new battery pack charges correctly, then the
original battery pack is defective and should be returned
to a service centre for recycling.
X If the new battery pack gives the same indication as the
original, take the charger to be tested at an authorized
service centre.
Note: It may take as long as fifteen minutes to determine that
the pack is defective.
If the battery pack is too hot or too cold, the LED will
alternately blink fast and slow, one flash at each speed and
repeat.
Battery chargers - daisy chaining (fig. C)
Single and dual port chargers can be electrically connected
in any order up to a maximum of 4 chargers. Each charger
has a power-in cord (12) which plugs into the electrical outlet
and a power-out cord (13) which plugs into the next charger.
To connect the chargers in a daisy chain:
X Plug the power-in cord (12) into an electrical outlet.
X Remove the power-in cord from the next charger and
plug in the power-out cord (13) rom the charger that is
now plugged into the outlet.
X Repeat this process for the remaining chargers.
Chargers that are daisy chained together operate
independently as though each one was plugged into a
separate outlet, therefore a battery can be removed from
anywhere along the daisy chain without affecting the other
chargers.
Use
Switching on and off (fig. D and E)
X To switch the tool on, press the variable speed trigger
switch (7).
X To switch the tool off, release the variable speed trigger
switch (7).
X A forward/reverse control button (4) determines the
direction of the tool and also serves as a lock off button.
X To select forward rotation, release the variable speed
trigger switch (7) and move the forward/reverse control
button (4) to the left, looking forward.
X To select reverse direction, move the forward/reverse
control button (4) in the opposite direction.
X The centre position of the control button (4) locks the
tool in the off position. Make sure that the variable speed
trigger switch (7) is released before changing the
position of the forward/reverse control button (4).
X If the tool does not turn on, check to see if one of the two
VPX™ battery packs is depleted. See the section
‘Battery LED indicators’ below.
Battery LED indicators
This product is equipped with electronics which will shut-off
the power when either battery pack is depleted. If the tool
stops suddenly, one of battery packs may be depleted. An
LED (14) on the back of the tool handle will indicate which
battery pack is depleted.
In order to illuminate the indicator (14) squeeze the variable
speed trigger switch (7). To insure optimal runtime, remove
both battery packs and place in a charger. Two battery
indicators are located on the back of the tool above the
batteries. If battery power is depleted while using your
appliance, you can determine which battery needs to be
recharged.
To check battery status:
X Squeeze the trigger and observe which LED is
illuminated.
X Remove the battery pack corresponding to the LED
which is illuminated.
Torque control (fig. D and E)
Your tool is fitted with a 24 position collar (2 or 8) to select
the operating mode and to set the torque for tightening
screws. Large screws and hard workpiece materials require
a higher torque setting than small screws and soft workpiece
materials.
X For drilling in wood, metal and plastics, set the collar to
the drilling position symbol.
X For screwdriving, set the collar to the desired setting. If
you do not know the appropriate setting, proceed as
follows:
X Set the collar to the lowest torque setting.
X Tighten the first screw.
X If the clutch ratchets before the desired result is
achieved, increase the collar setting and continue
tightening the screw. Repeat until you reach the correct
setting. Use this setting for the remaining screws.
Hammer action (VPX1222 only)
Your drill has hammer action:
X For drilling in masonry, set the torque control collar to
the position.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker vpx 1212 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker vpx 1212 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,77 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info