388385
6
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
6
ENGLISH
change to flashing (charging) state, as the charger
occasionally “tops off“ the battery charge.
X The charging indicator (10) will be lit as long as the
battery pack is connected to the plugged-in charger.
X Charge discharged batteries within 1 week. Battery life
will be greatly diminished if stored in a discharged state.
Charge indicators
If the charger detects a problem with a battery pack, the
charge indicator (10) will flash at a fast rate.
X If this occurs, re-insert the battery pack (8).
X If the problem persists, put a different battery pack in the
charger to determine if the charger is OK.
X If the new battery pack charges correctly, then the
original battery pack is defective and should be returned
to a service centre for recycling.
X If the new battery pack gives the same indication as the
original, take the charger to be tested at an authorized
service centre.
Note: It may take as long as fifteen minutes to determine that
the pack is defective.
If the battery pack is too hot or too cold, the LED will
alternately blink fast and slow, one flash at each speed and
repeat.
Battery chargers - daisy chaining (fig. C)
Single and dual port chargers can be electrically connected
in any order up to a maximum of 4 chargers. Each charger
has a power-in cord (11) which plugs into the electrical outlet
and a power-out cord (12) which plugs into the next charger.
To connect the chargers in a daisy chain:
X Plug the power-in cord (11) into an electrical outlet.
X Remove the power-in cord from the next charger and
plug in the power-out cord (12) from the charger that is
now plugged into the outlet.
X Repeat this process for the remaining chargers.
Chargers that are daisy chained together operate
independently as though each one was plugged into a
separate outlet, therefore a battery can be removed from
anywhere along the daisy chain without affecting the other
chargers.
Use
Switching on and off (fig. D)
X To switch the tool on, press the on/off trigger switch (7).
X To switch the tool off, release the on/off trigger
switch (7).
X A forward/reverse control button (4) determines the
direction of the tool and also serves as a lock off button.
X To select forward rotation, release the on/off trigger
switch (7) and move the forward/reverse control button
(4) to the left.
X To select reverse direction, move the forward/reverse
control button (4) in the opposite direction.
X The centre position of the control button (4) locks the
tool in the off position. Make sure that the on/off trigger
switch (7) is released before changing the position of
the forward/reverse control button (4).
Torque control (fig. D)
Your tool is fitted with an 8 position collar (2) to select the
operating mode and to set the torque for tightening screws.
Large screws and hard workpiece materials require a higher
torque setting than small screws and soft workpiece
materials.
X For drilling in wood, metal and plastics, set the collar (2)
to the drilling position symbol.
X For screwdriving, set the collar to the desired setting. If
you do not know the appropriate setting, proceed as
follows:
X Set the collar to the lowest torque setting.
X Tighten the first screw.
X If the clutch ratchets before the desired result is
achieved, increase the collar setting and continue
tightening the screw. Repeat until you reach the correct
setting. Use this setting for the remaining screws.
High/low speed selector (fig. D)
The 2-speed feature of your drill allows for greater versatility.
X To select the low speed, high torque setting (position 1),
turn the tool off and allow it to stop. Move the speed
selector button (3) to the right.
X To select the high speed, low torque setting (position 2),
turn the tool off and allow it to stop. Move the speed
selector button (3) to the left.
Warning! Do not move the speed selector button with the
tool switched on.
Keyless chuck (fig. E)
To insert a drill bit or other accessory:
X Hold the chuck (1) and rotate it in a counter clockwise
direction, as viewed from the chuck end.
X Insert the bit or other accessory fully into the chuck, and
tighten securely by rotating the chuck (1) in the
clockwise direction.
Warning! Do not attempt to tighten drill bits (or any other
accessory) by gripping the chuck and turning the tool on or
damage to the chuck and personal injury may occur.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker vpx 1201 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker vpx 1201 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info