426955
12
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
12
ENGLISH
Fitting the centring pin (fig. O)
Fit the edge guide to the router as shown in
fig. C, but upside down.
Fit the centring pin (22) to the workpiece side
of the edge guide with the screw (23) provided.
Fitting the copy follower (fig. P)
Fit the edge guide to the router as shown in
fig. C.
Fit the ‘L’ bar (24) to the upper side of the edge
guide using the two screws and nuts provided.
Fit the rotating attachment (25) to the ‘L’ bar
with the wing screw provided.
USE
Let the tool work at its own pace.
Do not overload.
Carefully guide the cable in order to avoid
accidentally cutting it.
Adjusting the depth of cut (fig. E)
The depth of cut is the distance X between the
depth stop bar (9) and the depth stop (18).
The depth of cut can be set in two different ways
as described below.
Adjusting the depth of cut using a piece of wood
(fig. A & F)
Fit the router bit as described above.
Loosen the locking screw (10).
Pull the plunge lock lever (4) up.
Plunge the router down until the router bit
touches the workpiece.
Push the plunge lock lever (4) down.
Pull the depth stop bar (9) up.
Place a piece of wood with a thickness equal to
the desired depth of cut between the depth
stop (18) and the depth stop bar (9).
Tighten the locking screw (10).
Remove the piece of wood.
Pull the plunge lock lever (4) up and let the
router return to its original position.
After switching the router on, plunge it down
and make the desired cut.
Adjusting the depth of cut using the scale
(fig. A & G)
Fit the router bit as described above.
Loosen the locking screw (10).
Pull the plunge lock lever (4) up.
Plunge the router down until the router bit
touches the workpiece.
Push the plunge lock lever (4) down.
Read the starting position from the scale (11).
Add the desired depth of cut to the starting
position.
Move the depth stop bar (9) to the calculated
position on the scale.
Tighten the locking screw (10).
Pull the plunge lock lever (4) up and let the
router return to its original position.
After switching the router on, plunge it down
and make the desired cut.
Adjusting the revolver depth stop (fig. H)
After turning the revolver depth stop to the desired
setting, you can fine-adjust the depth stop to be used.
If you want to make several cuts with a different
depth of cut, adjust each of the depth stops.
Turn the depth stop screw (19) up or down as
required using a screwdriver.
Setting the speed (fig. A)
Set the speed control knob (3) to the required
speed. Use a high speed for small diameter
router bits. Use a low speed for large diameter
router bits.
Using a batten as a guide (fig. I)
When it is not possible to use the edge guide,
for example when routing grooves in the back
panel of a bookcase to support shelves,
proceed as follows:
Place a batten onto the workpiece.
Move the batten until it is in the correct
position to guide the tool.
Securely clamp the batten to the workpiece.
Using the template guide (fig. M)
The template guide can be used to make a cutout
shape from a template, for instance a letter.
Secure the template over the workpiece with
double-sided tape or ‘G’ clamps.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker kw 850 e bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker kw 850 e in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info