381280
10
Verklein
Vergroot
Pagina terug
1/104
Pagina verder
10
ENGLISH
To charge the battery, set the
tool to the straight position
and insert the charger plug
(10) into the connector (11).
Plug in the charger. Switch on
at the mains.
Leave the tool connected to the
charger for at least 12 hours.
The tool can be left connected to
the charger indefinitely.
The charger may hum and become
warm while charging; this is normal
and does not indicate a problem.
Before using the tool, unplug
the charger and disconnect
the tool from the charger.
Do not use the tool while it
is connected to the charger.
Adjusting the handle (fig. D)
For optimum versatility, the
handle can be set to different
positions.
Press the handle adjustment
button (4).
Swivel the handle into the
desired position.
Release the button.
KC9036 - Manual spindle lock
(fig. E)
The manual spindle lock allows
you to use the tool as a regular
screwdriver. You can give an
extra twist to firmly tighten a
screw or to loosen a very tight
screw.
To activate the spindle lock,
turn the collar (2) to the
symbol. With the spindle lock
activated, the tool cannot be
switched on.
To release the spindle lock,
turn the collar (2) to the
symbol.
KC9039 - Setting the torque
(fig. E)
This tool is fitted with a collar to
set the torque for tightening
screws.
Large screws and hard workpiece
materials require a higher torque
setting than small screws and soft
workpiece materials. The collar
has a wide range of settings to
suit your application.
Turn the collar (2) to the
desired setting. If you do not
yet know the appropriate
setting, proceed as follows:
- Set the collar to the lowest
torque setting.
- Tighten the first screw.
- If the clutch ratchets before
the desired result is achieved,
increase the collar setting and
continue tightening the
screw. Repeat until you reach
the correct setting. Use this
setting for the remaining
screws.
Operating the tool (fig. F)
Make sure that the spindle
lock is released.
To tighten a screw or nut,
slide the on/off switch (1) to
the right and press it.
To loosen a screw or nut,
slide the on/off switch (1) to
the left and press it.
To switch the tool off, release
the on/off switch.
Hints for optimum use
Always use the correct type
and size of screwdriver bit.
If screws are difficult to
tighten, try applying a small
amount of washing liquid or
soap as a lubricant.
Use the spindle lock to loosen
very tight screws or to firmly
tighten screws.
Always hold the tool and
screwdriver bit in a straight
line with the screw.
When screwing in wood, it is
recommended to drill a pilot
hole with a depth equal to
the length of the screw.
KC9036EUR.PM65 25-06-2001, 14:5310
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker kc 9036 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker kc 9036 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Fins als bijlage per email.

De handleiding is 0,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info