709494
13
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
13
ENGLISH
(Original instructions)
u Press the release tabs (29) on the line spool cap (30),
as shown in gure R and remove the cap by pulling it
straight off.
u Pull the spool (31) out of the spool cap and clear any
broken line or cutting debris from the spool area.
u Before placing a new spool, "park" the cutting line (32)
in the holding slots (33).
u Feed the end of each line through the two holes (34) on
either side of the the spool cap ( 31 ) as shown in gure S
u Slide the spool back into the spool cap. Take care to
keep the line from becoming trapped under the spool.
u Pull slack line through until it pulls out of the holding
slots.
u Align the tabs on the spool cap with the slots in the
housing (gure R).
u Push the cap onto the housing until it snaps securely
into place.
Note: Make sure that cap is fully positioned, listen for two
audible clicks to ensure both lugs are correctly located.
Power the appliance on. In a few seconds or less you’ll hear
the nylon line being cut automatically to the proper length.
Caution: To avoid appliance damage, if the cutting line
protrudes beyond the trimming blade, cut it off so that it just
reaches the blade.
Note: Other replacement parts (guards, spool caps, etc.)
are available through BLACK+DECKER service centers. To
nd your local service location visit www.blackanddecker.com.
Warning! The use of any accessory not recommended
by BLACK+DECKER for use with this appliance could be
hazardous.
Note: The tool has two cutting systems:
u AFS: Single line autofeed for light trimming and edging.
u HDL: Heavy Duty Dual Line cutting system for more
overgrown areas.
Note: The HDL spool may be used in trimming mode only.
Fitting a new piece of heavy duty cutting line (g.
T & U)
Replacement packs of 10 heavy duty cutting lines are
available from your BLACK+DECKER dealer (cat. no. A6489).
To t a new piece of cutting line, proceed as follows:
u Unplug the tool.
u Keep the tabs (37) depressed and remove the HDL cap
(16) from the housing (12).
u Remove any dirt and grass from the HDL cap (16) and
housing.
u Remove the used piece of line from the HDL cap (16).
u Thread a new piece of line (35) through the eyelets (36) in
either side of the HDL cap.
u Put the central ferrule (39) in the indicated position (Fig.
U).
u Re-t the HDL cap.
Rewinding spool from bulk line (use only 20mm.
round diameter line)
Do not use square, star or other shaped line or larger
diameter. These may cause feeding issues or overload the
motor.
Bulk line is also available for purchase from your local retailer.
Note: Hand wound spools from bulk line are likely to
become tangled more frequently than BLACK+DECKER
factory wound spools. For best results, factory wound spools
are recommended.
To install bulk line, follow the steps below:
u Remove battery from appliance.
u Remove the empty spool from the appliance as
described in “Replacing the spool.”
u Remove any remaining cutting line from the spool.
u First, wind new line in the channel of the spool closest
to the holding slots as shown in Figure V.
u Place the end of the cutting line (32) into the retaining
hole (40) (Figure W).
u Wind the cutting line onto the spool in the direction
of the arrow on the bottom of the spool. Make sure to
wind the line on neatly and in layers. Do not crisscross.
u When the wound cutting line reaches the beginning of the
holding slots, cut the line approximately 106 mm.
u Push the line in the holding slot on one side of the spool
to hold the rst line while you wind the second line.
u Repeat the above procedure for the second cutting line
on the lower section of the spool.
u Fit the spool into the appliance as described in
“Replacing the spool".
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool/appliance care and regular
cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your tool/appliance
and charger using a soft brush or dry cloth.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker STC5433B bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker STC5433B in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 6,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info