709484
12
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
12
ENGLISH
(Original instructions)
Also clean out any grass or debris which may be packed
around the discharge opening. Replace the grass catcher.
u If mower should start to vibrate abnormally, release bail
handle to turn mower off and remove safety key. Check
immediately for cause. Vibration is a warning of trouble.
Do not operate mower until a service check has been
made.
Refer to troubleshooting guide in manual.
u Always release bail handle to turn mower off when leaving
it unattended even for a short period of time.
Removing and installing blade
Warning! When reassembling the blade system, ensure each
part is reinstalled correctly, as described below.
Improper assembly of the blade or other parts of the blade
system may cause serious injury.
Warning! Release bail handle to turn mower off, wait for the
blade to stop, and unplug mower.
u Cut a piece of 2x4 wood (27) (about 610 mm) to keep
blade from turning while removing bolt (28).
u Wear gloves and proper eye protection.
u Turn the mower on its side. Be careful of sharp edges of
blade. Position wood and unscrew bolt with 9/16” wrench
(29) as shown in gure S.
u Note the orientation of each part as you remove it.
Remove nut (30). Pull off washer (31), the blade insulator
(32), and the blade (33) as shown in Figure T. Examine all
pieces for damage and replace if necessary.
Note: The fan should not be able to be removed.
u To reassemble, slide the blade (33) on. It can only be at-
tached to the fan in one direction and location. Line up the
D-shaped hole of the blade with the D-shaped post of the
fan, ensuring the writing on the blade faces out away from
the mower. Place the insulator (32) on the blade so that
the two outer ribs extend past the blade. Place the square
washer (31) on top of the insulator so that it sits inside of
the two outer ribs on the insulator. Replace the nut (30)
with the wide side against the washer.
u To tighten rmly, position the piece of wood as shown
in gure U to keep the blade from turning. Slide the bolt
through the washer and screw bolt into place. Tighten with
the wrench.
Blade sharpening
Keep blade sharp for best mower performance. A dull blade
does not cut grass cleanly. Use proper eye protection while
removing, sharpening, and installing blade. Ensure that safety
key and battery pack is removed.
Sharpening the blade twice during a mowing season is usually
sufcient under normal circumstances. Sand causes the
blade to dull quickly. If your lawn has sandy soil, more frequent
sharpening may be required.
Note: Replace bent or damaged blade immediately.
When sharpening the blade:
u Make sure blade remains balanced.
u Sharpen blade at the original cutting angle.
u Sharpen cutting edges on both ends of blade, removing
equal amounts of material from both ends.
To sharpen blade in a vise (g. V)
u Be sure the bail handle is released, the blade has stopped
and the mower is unplugged before removing the blade.
u Remove blade from mower. See instructions for removing
and installing blade.
u Secure blade (33) in a vise (36).
u Wear proper eye protection and gloves and be careful not
to cut yourself.
Carefully le the cutting edges of the blade with a ne
tooth le (39) or sharpening stone, maintaining the angle
of the original cutting edge. Check balance of blade. See
instructions for blade balancing. Replace blade on mower
and tighten securely.
Blade balancing
Check balance of the blade (35) by placing centre hole in
the blade over a nail or round shank screwdriver, clamped
horizontally in a vise. if either end of the blade rotates down-
ward, le along the sharp edge of that dropping end. Blade is
properly balanced when neither end drops.
Lubrication
No lubrication is necessary. Do not oil the wheels. They have
plastic bearing surfaces which require no lubrication.
Cleaning
Release bail handle (2) to turn mower off, let the blade come
to a stop and then remove safety key. Use only mild soap
and a damp cloth to clean the mower. Clean out any clippings
which may have accumulated on the underside of the deck.
After several uses, check all exposed fasteners for tightness.
Preventing corrosion
Fertilizers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals. If you mow in areas
where fertilizers or chemicals have been used, the mower
should be cleaned immediately afterward as follows: Release
bail handle (2) to turn mower off and unplug mower. Wipe all
exposed parts with a damp cloth.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory opera-
tion depends upon proper tool/appliance care and regular
cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your tool/appliance
and charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u Regularly use a blunt scraper to remove grass and dirt
from the underneath of the guard.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker LM2000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker LM2000 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 6,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info