580932
24
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
24
ENGLISH
All models
Note: To achieve a greater accuracy of cut, ensure
back of blade is touching blade support roller. See
‘Blade suport roller’ for instructions on how to change
position of blade support roller.
BLADE SUPPORT ROLLER
To provide greater support and accuracy when cutting,
your jigsaw is fitted with a blade support roller. This
support should be adjusted so that the roller touches
the back of the blade when cutting.
To do this, loosen the front
screw on the base of the
shoe. Push the blade
support forward until the
roller touches the back
edge of the blade. Retighten
the screw. Lubricating the
guide roller (5) from time to time with a drop of oil will
extend the life of the roller.
For scroller jigsaws only
Note: When using your jigsaw in the scrolling mode,
the blade support roller needs to be retracted to allow
free movement of the blade.
To do this, untighten the
front screw on the base of
the shoe and retract the
support. Re-tighten the
screw.
OPERATING YOUR JIGSAW
To switch your jigsaw on, fully squeeze the on/off
trigger switch (1). To switch your jigsaw off, release
the trigger switch (1). When plugging your jigsaw in,
ensure the trigger switch is in the OFF position.
When continuous operation is required, squeeze the
trigger and depress the lock on button (2) and release
the trigger. To disengage the lock, squeeze and release
the trigger. Always disengage the lock before
disconnecting from the power supply.
SAW SHOE ADJUSTMENT FOR ANGULAR CUTTING
The shoe plate (6) can be angled up to 45˚ on either side.
To do this, disconnect your jigsaw from the power supply.
Raise or remove the dust
shroud (4) and loosen both
screws on the shoe plate
with a screwdriver. Pull the
shoe plate backward a little,
and set the desired angular
adjustment according to the
scale or push the shoe plate
forward for fixed locks at 0˚,
15˚, 30˚, or 45˚. Tighten the
screws to secure. Although
the scale and notches are
accurate for most purposes
it is advisable for very
accurate angle cutting to use a protractor to set the
shoe. Make a test cut on some scrap material to check
the accuracy of the angle. To reset the shoe for a
square cut, slacken the clamp screws and move the
shoe until it is approximately 90˚ to the blade, and then,
whilst applying slight forward pressure on the shoe,
retighten the clamp screws. If necessary, re-adjust the
blade support roller using only the front screw.
DUST BLOWING
To aid visibility when cutting,
your jigsaw is fitted with a
facility which will blow dust
away from surface of
material being cut. To utilise,
lift up or remove dust visor
and ensure the variable
blower control is pointing towards the symbol.
DUST EXTRACTION
Your jigsaw with a hose adapter (accessory part), can
be fitted to most portable vacuum cleaners.
To utilise this facility push
adapter into the aperture at
the rear of jigsaw and fit
vacuum hose in or over the
adapter, depending on the
hose size. The dust shroud
should be attached and in a
downwards position and
the variable blower control
on the side of the jigsaw
should point towards the
symbol.
ELECTRONIC SPEED REGULATION
For electronic models only
The electronic speed
control wheel (3) is used to
programme the required
saw speed depending on
the material being worked.
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker KS634S T1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker KS634S T1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 4,74 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Black Decker KS634S T1

Black Decker KS634S T1 Snelstart handleiding - English - 12 pagina's

Black Decker KS634S T1 Gebruiksaanwijzing - Polski - 48 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info