579744
9
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
9
u The height difference between the toothed rim and the
lower end of the riving knife should be 2 - 3 mm.
u Tighten the screws.
Fitting and removing the parallel fence (g. C)
u The parallel fence is used to saw in a straight line parellel
to the edge of the workpiece.
Fitting
u Loosen the locking knob (18).
u Insert the parallel fence (19) through the openings (20).
u Slide the parallel fence into the desired position.
u Tighten the locking knob.
Removing
u Loosen the locking knob.
u Pull the parallel fence off the tool.
Use
Warning! Let the tool work at its own pace. Do not overload.
This tool can be used in the right hand or the left hand.
Adjusting the sawing angle (g. D)
The default angle between the saw blade and the shoe is 90°.
u Use a square to check that the angle between the saw
blade and the shoe is 90°. If the angle does not measure
90° adjust as follows:
u Loosen the locking knob (21) to unlock the saw shoe.
u Loosen the locknut (22) on the adjusting screw (23).
u Screw the adjusting screw in or out to achieve a 90° angle.
u Retighten the locknut.
u Tighten the locking knob to lock the saw shoe in place.
Adjusting the depth of cut (g. E)
The depth of cut should be set according to the thickness of
the workpiece. It should exceed the thickness by approx.
2 mm.
u Loosen the knob (24) to unlock the saw shoe.
u Move the saw shoe (8) into the desired position.
The corresponding depth of cut can be read from the
scale (25).
u Tighten the knob to lock the saw shoe in place.
Adjusting the bevel angle (g. F)
This tool can be set to bevel angles between 0° and 45°.
u Loosen the locking knob (21) to unlock the saw shoe.
u Move the saw shoe (10) into the desired position.
The corresponding bevel angle can be read from the
scale (26).
u Tighten the locking knob to lock the saw shoe in place.
Switching on and off
u To switch the tool on, move the lock-off button (2) into the
unlock position and squeeze the on/off switch (1).
u To switch the tool off, release the on/off switch.
Sawing
Always hold the tool with both hands.
u Let the blade run freely for a few seconds before starting
the cut.
u Apply only a gentle pressure to the tool while performing
the cut.
u Work with the shoe pressed against the workpiece.
Hints for optimum use
u As some splintering along the line of cut on the top side of
the workpiece cannot be avoided, cut on the side where
splintering is acceptable.
u Where splintering is to be minimised, e.g. when cutting
laminates, clamp a piece of plywood onto the top of the
workpiece.
Using the sight guide (g. G)
The tool is equipped with a sight guide for straight cutting (27)
and for 45° bevel cutting (28).
u Adjust the sight guide as described below.
u Align the left edge of the guides (27) or (28) with the
cutting line (29).
u Keep the sight guide aligned with the cutting line while
sawing.
u Work with the shoe pressed against the workpiece.
Adjusting the sight guide
u Make a test cut halfway through a piece of scrap wood.
u Withdraw the saw so the cutting line (29) becomes visible.
u While keeping the saw in this position, loosen the sight
guide on the saw shoe as shown.
u Align the 0° mark (27) on the sight guide with the cutting
line (29). When adjusting for 45° bevel cuts, align the 45°
mark (28) on the sight guide with the cutting line.
u Secure the sight guide using the screw (30).
How to use the laser (g. H)
The laser projects the line of cut on the workpiece surface.
u To switch the laser on, slide the switch (6) forward.
u To switch the laser off, slide the switch (6) backward.
Viewing from directly above the saw, the line of cut can be
easily followed. Should this view be restricted for any
reason, the laser can be used as an alternate cutting
guide.
u Use a pencil to mark the cutting line.
u Position the saw over the line.
u Switch on the laser.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker KS1501L T1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker KS1501L T1 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Black Decker KS1501L T1

Black Decker KS1501L T1 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanôl, Espanõl - 104 pagina's

Black Decker KS1501L T1 Gebruiksaanwijzing - Polski - 16 pagina's

Black Decker KS1501L T1 Gebruiksaanwijzing - Polski - 104 pagina's

Black Decker KS1501L T1 Gebruiksaanwijzing - Türkiye - 12 pagina's

Black Decker KS1501L T1 Gebruiksaanwijzing - Dansk, Svenska, Norsk, Suomi - 104 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info