497046
8
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
8
ENGLISH
Charging the battery (fig. C)
The battery needs to be charged before first use
and whenever it fails to produce sufficient power
on jobs that were easily done before.
When charging the battery for the first time,
or after prolonged storage, it will only accept an
80% charge. After several charge and discharge
cycles, the battery will attain full capacity.
The battery may become warm while charging;
this is normal and does not indicate a problem.
Do not charge the battery at ambient
temperatures below 4 °C or above 40 °C.
Recommended charging temperature:
approx. 24 °C.
To charge the battery, insert the charger plug
(7) into the connector (3).
Plug in the charger. Switch on at the mains.
Leave the tool connected to the charger for at
least 12 hours.
The tool can be left connected to the charger
indefinitely. The charger may hum and become
warm while charging; this is normal and does not
indicate a problem.
Before using the tool, unplug the charger and
disconnect the tool from the charger.
Do not use the tool while it is connected
to the charger.
Operating the tool (fig. D)
To tighten a screw or nut, slide the on/off
switch (1) to the right and press it.
To loosen a screw or nut, slide the on/off
switch (1) to the left and press it.
To switch the tool off, release the on/off switch.
Hints for optimum use
Always use the correct type and size of
screwdriver bit.
If screws are difficult to tighten, try applying a
small amount of washing liquid or soap as a
lubricant.
Use the spindle lock to loosen very tight
screws or to firmly tighten screws.
Always hold the tool and screwdriver bit in a
straight line with the screw.
When screwing in wood, it is recommended to
drill a pilot hole with a depth equal to the
length of the screw. A pilot hole guides the
screw and prevents splintering or distortion of
the wood. For the optimum size of the pilot
hole, refer to the table below.
When screwing in hardwood, also drill a
clearance hole with a depth equal to half the
length of the screw. For the optimum size of
the clearance hole, refer to the table below.
Screw size No. 6 No. 8 No. 10
(3.5 mm) (4 mm) (6 mm)
Pilot hole ø
(softwood) 2 mm 3.2 mm 3.5 mm
Pilot hole ø
(hardwood) 2.5 mm 3.5 mm 4.0 mm
Clearance hole 4 mm 5.0 mm 5.7 mm
MAINTENANCE
Your Black & Decker tool has been designed to
operate over a long period of time with a
minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and
regular cleaning.
Your charger does not require any maintenance
apart from regular cleaning.
Unplug the charger before cleaning it.
Regularly clean the ventilation slots in your tool
using a soft brush or dry cloth.
Regularly clean the motor housing using a
damp cloth. Do not use any abrasive or
solvent-based cleaner.
PROTECTING THE ENVIRONMENT
Tools
Should you find one day that your tool
needs replacement, or if it is of no further
use to you, think of the protection of the
environment. Black & Decker repair agents
will accept old Black & Decker tools and
ensure that they are disposed of in an
environmentally safe way.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker KC9024 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker KC9024 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 0,69 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info