578034
8
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
8
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time.
Labels on tool
The following pictograms are shown on the tool:
:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Fit the dustbag or dust cassette before using the tool
on wooden workpieces.
Remove the dustbag or cassette and t the deector
before using the tool on workpieces containing
metal.
Electrical safety
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
Your tool has some or all of the following features:
1. On/off switch
2. Variable speed control knob
3. Lock-on button
4. Secondary handle
5. Belt tensioning lever
6. Belt tracking knob
7. Straight arm
Fig. A
8. Narrow arm
9. Cranked arm
Fig. D
10. Dust cassette
11. Deector
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting and removing sanding arms (g. A & B)
The tool is supplied with the following sanding arms:
u Straight arm (7), sanding width 13 mm
u Narrow arm (8), sanding width 6 mm, for intricate work
u Cranked arm (9) for grooving and sanding in the centre of
workpieces and for reaching conned areas
Before rst use, you must t the sanding arm to the tool.
Fitting
u Make sure that the belt tensioning lever (5) is in the
position shown.
u Loosen and remove the belt tracking knob (6).
u Remove the tape retaining the spring (12) (if present).
u Check that the spring (12) is located in its mounting hole.
u Position the arm as shown.
u Fit the belt tracking knob (6) and tighten it until the arm (7)
is aligned with the tool.
Removing
u Remove the sanding belt (13) (if present) as described below.
u Loosen and remove the belt tracking knob (6).
u Remove the arm.
Warning! Be careful not to lose the spring (12).
Fitting and removing sanding belts (g. B)
Warning! The spring must be tted. Be careful not to lose the
spring (12).
Fitting
u Move the belt tensioning lever (5) to the front position (A).
u Make sure that the arrows on the inside of the sanding
belt (13) face the same direction as the arrows (14) on the
housing.
u Place the sanding belt (13) over the front pulley (15) and
the rear pulley (16), sliding it through the slot in the
housing.
u Move the belt tensioning lever (5) to the rear position (B).
u Adjust the belt tracking as described below.
Removing
u Move the belt tensioning lever (5) to the front position (A).
u Slide the sanding belt (13) off the pulleys.
Adjusting the sanding belt tracking (g. C)
u Switch the tool on.
u Turn the belt tracking knob (6) as required until the
sanding belt (13) runs straight along the length of the arm.
Fitting and removing the dust cassette (g. D & F)
Warning! Always remove the dust cassette and t the
deector when using the tool on metal workpieces.
u Fit the dust cassette (10) over the dust extraction outlet.
u Slide the item onto the tool and make sure that it is
securely located.
u To remove the dust cassette, pull it to the rear and off the
outlet.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker KA902E T1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker KA902E T1 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Black Decker KA902E T1

Black Decker KA902E T1 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanõl - 84 pagina's

Black Decker KA902E T1 Gebruiksaanwijzing - Türkiye - 12 pagina's

Black Decker KA902E T1 Gebruiksaanwijzing - Dansk, Svenska, Norsk, Suomi - 84 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info