Handleiding Black Decker HVLP200 T1 (pagina 10 van 112) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins)

578632

Verklein

Vergroot

Pagina terug

1/112

Pagina verder

ENGLISH

(Original instructions)

Note : Always test the spray pattern on scrap cardboard

or similar material rst. Begin with ow control knob on the

highest ow setting. If less ow is desired, dial the ow control

knob in. Heavier, thicker materials should be sprayed with the

indicator close to the (+) icon. Thinner materials should be

sprayed with the indicator close to the (-) icon.

Note : If the ow control setting is set completely to the

minimum side, the trigger will have limited or no travel. Back

the ow control knob off (clockwise) to allow for more trigger

travel.

Liquid material preparation (g. J & K)

Note : Make sure the type of material you use can be cleaned

with either mineral spirits or paint thinner (for oil-based paints)

or a warm water and soap solution (for water soluble paints

like latex). Use drop cloths to protect your oors and anything

else in the spraying area that you wish to remain untouched.

The liquid being sprayed may need to be thinned (diluted)

before staring. When thinning, use the proper liquid thinner

recommended on the container by the material manufacturer.

Warning! Do not use materials with a ashpoint lower than

55°C.

Note : A mixing bucket (12) is provided to use when transfer-

ring spray material from the original container into the bucket

for thinning and measuring purposes (g. J).

Note : A viscosity cup (13) is provided to determine the

“runout time” of the material being used.

u Before measuring for the proper viscosity, stir the material

thoroughly.

u Dip the viscosity cup (13) into the material being sprayed

and ll the viscosity cup (13) completely.

u With the viscosity cup (13) held over the material con-

tainer, measure the amount of time it takes for the stream

of material owing out to “break” or stop being a constant

stream out of the bottom of the viscosity cup (13) (2

minutes or less) (g. K). This is the “runout time” Refer to

the thinning table for information on the thinning required

for different materials.

u If material needs thinning, add the appropriate liquid thin-

ning material recommended by the manufacturer.

u It is possible to spray latex paint with this unit, however,

the required thinning may exceed material manufacturer's

recommendation. Thin latex paint so that it runs through

viscosity cup (13) in under 2 minutes. The operator should

consider the type of application and nal location of the

project when spraying a material that requires more than 2

minutes to run through the viscosity cup (13).

Thinning table

Spray material Runout time

Clear and semi-transparent stains

and sealers

No thinning required

Oil based primers, varnishes and

polyurethane

(Less than 2 minute runout)

Solid colour water based stains May require thinning

Water based or latex paints (More than 2 minute runout)

Note : Not recommended for textured paint

Hints for optimum use

Preparation tips

u Always stir and strain the material thoroughly before use.

u With any spraying job you should always ensure that

you have properly prepared the surface to get the best

nish. That is, all surfaces are free from dust, dirt, rust and

grease. Lightly pressure wash decks or exterior surfaces

and ensure that they are dry before spraying.

u Even though HVLP sprayers have very little overspray,

it is recommended that you mask all edges and other

areas and use drop cloths to protect your oors and

anything else in the spraying area that you wish to remain

untouched.

u Skin that forms on the top of paint can clog the sprayer.

Remove skin before mixing. Strain with a funnel with a

lter attached or through hosiery to remove any impurities

that could clog system.

u Before starting have gloves, paper towels, rags etc. avail-

able for unexpected spills.

Developing the proper spraying technique (g. L & M)

u Practice spraying on a piece of scrap material such as

cardboard to test your spray pattern and become familiar

with the ow control feature of the sprayer.

u Ensure surface to be sprayed is free of dust, dirt, and

grease.

u Ensure spray area is clean and free of dust that could be

blown onto newly sprayed surfaces.

u Cover any areas not intended to be sprayed.

u Always spray from a minimum of 25mm to a maximum of

355mm (g. L).

u A commonly used method for spraying a large surface

is the “crisscross” pattern. This is done by spraying in

horizontal strips and then crossing over these strips with

vertical strips.

u To get an even spray distribution, always keep your arm at

the same distance (g. L) from the surface you are spray-

ing and avoid moving your wrist (g. M).

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Black Decker HVLP200 T1 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Black Decker HVLP200 T1

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info