31950
12
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
12
For screwdriving, set the collar to the desired
setting. If you do not yet know the appropriate
setting, proceed as follows:
Set the collar (3) to the lowest torque setting.
Tighten the first screw.
If the clutch ratchets before the desired
result is achieved, increase the collar setting
and continue tightening the screw. Repeat
until you reach the correct setting. Use this
setting for the remaining screws.
HP122K(D)/HP142K(D) - Drilling in masonry
(fig. H & I)
For drilling in masonry, set the collar (3) to the
hammer drilling position by aligning the
symbol with the marking (21).
Slide the two-gear selector (5) towards the
front of the tool (2nd gear).
HP122K(D)/HP142K(D) - Two-gear selector (fig. I)
For drilling in steel and for screwdriving
applications, slide the two-gear selector (5)
towards the rear of the tool (1st gear).
For drilling in materials other than steel,
slide the two-gear selector (5) towards the
front of the tool (2nd gear).
Straight drilling indicator (fig. J)
This tool is fitted with an indicator to facilitate
straight drilling. This feature can be used both in
horizontal and in vertical position.
Position the tool as required.
Keep the switch (1) slightly depressed without
switching the tool on.
Slowly move the rear of the tool until the red
indicator (22) lights up.
Press the switch further to start drilling.
HP12KD/HP14KD/HP122KD/HP142KD -
Detecting pipes or wires (fig. K)
Take the detector (23) out of the holder (24).
Refer to the manual of the detector for further
instructions.
Drilling/screwdriving (fig. A)
Select forward or reverse rotation using the
forward/reverse slider (2).
To switch the tool on, press the switch (1).
The tool speed depends on how far you press
the switch.
To switch the tool off, release the switch.
Hints for optimum use
Drilling
Always apply a light pressure in a straight line
with the drill bit.
Just before the drill tip breaks through the
other side of the workpiece, decrease pressure
on the tool.
Use a block of wood to back up workpieces
that may splinter.
Use spade bits when drilling large diameter
holes in wood.
Use HSS drill bits when drilling in metal.
Use masonry bits when drilling in soft masonry.
Use a lubricant when drilling metals other than
cast iron and brass.
Make an indentation using a centre punch at
the centre of the hole to be drilled in order to
improve accuracy.
Screwdriving
Always use the correct type and size of
screwdriver bit.
If screws are difficult to tighten, try applying a
small amount of washing liquid or soap as a
lubricant.
Always hold the tool and screwdriver bit in a
straight line with the screw.
MAINTENANCE
Your Black & Decker tool has been designed to
operate over a long period of time with a
minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and
regular cleaning.
Your charger does not require any maintenance
apart from regular cleaning.
Before performing any maintenance on
the tool, remove the battery from the
tool.
Unplug the charger before cleaning it.
ENGLISH
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker HP122KH bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker HP122KH in de taal/talen: Engels als bijlage per email.

De handleiding is 1,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Black Decker HP122KH

Black Decker HP122KH Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanôl, Dansk, Svenska, Norsk, Suomi - 104 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info