583272
13
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
13
In trimming mode, set the plant protector to
position A.
In edging mode, set the plant protector to
position B or C.
When there are no plants near the cutting
area, set the plant protector to position D.
MAINTENANCE
Your Black & Decker tool has been designed to
operate over a long period of time with a
minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and
regular cleaning.
Before performing any maintenance,
switch off and unplug the tool.
Regularly clean the ventilation slots in your tool
using a soft brush or dry cloth.
Regularly clean the cutting line and spool
using a soft brush or dry cloth.
Regularly use a blunt scraper to remove grass
and dirt from the underneath of the guard.
Fitting a new spool of cutting line (fig. K & L)
Replacement spools of cutting line are available
from your Black & Decker dealer (cat. no. A6441).
Complete cassettes containing a spool of cutting
line are also available (cat. no. A6442).
Unplug the tool.
Keep the tabs (21) depressed and remove the
spool cover (22) from the housing (23) (fig. K).
Remove the empty spool (24) from the
spool cover.
Remove any dirt and grass from the spool
cover and housing.
Take the new spool and push it onto the boss
in the spool cover. Rotate the spool slightly
until it is seated.
Unclip the end of one of the cutting lines and
guide the line into one of the eyelets (25) (fig. L).
The line should protrude approx. 9 cm from the
spool cover.
Unclip the end of the other cutting line and
guide the line into the other eyelet. The line
should protrude approx. 9 cm from the
spool cover.
Align the tabs (21) on the spool cover with the
holes (26) in the housing (fig. K).
Push the cover onto the housing until it snaps
securely into place.
If the cutting lines protrude beyond the
trimming blade (12), cut them off so that
they just reach the blade.
Winding new line onto an empty spool
(fig. M, N & P)
You may wind new cutting line onto an empty
spool. Replacement packs of cutting line are
available from your Black & Decker dealer
(cat. no. A6440).
Remove the empty spool from the tool as
described above.
Remove any remaining cutting line from
the spool.
First wind new line onto the uppermost part of
the spool:
- Feed 2 cm of cutting line into one of the slots
in the upper section of the spool as shown.
- Wind the cutting line onto the spool in the
direction of the arrow. Make sure to wind the
line on neatly and in layers. Do not criss-cross.
- When the wound cutting line reaches the
recesses (28), cut the line.
- Temporarily park the line in the slots (27) on
one side of the spool as shown.
Repeat the above procedure for the second
cutting line on the lower section of the spool.
Park the line in the unused slots (27).
Proceed as described above to fit the spool on
the tool. Do not forget to release the cutting
line from the parking slots (27).
Only use the appropriate type of
Black & Decker cutting line. Ensure that
cutting line is present in both sections of
the spool (fig. P).
TROUBLESHOOTING
If your tool seems not to operate properly, follow
the instructions below. If this does not solve the
problem, please contact your local Black & Decker
repair agent.
ENGLISH
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker GL670P T2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker GL670P T2 in de taal/talen: Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Black Decker GL670P T2

Black Decker GL670P T2 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanõl, Dansk, Svenska, Norsk, Suomi - 80 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info