527588
9
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
9
ENGLISH
If the tool starts running slowly, reduce the load.
In order to achieve optimum cutting results,
only cut dry grass.
MAINTENANCE
Your Black & Decker tool has been designed to
operate over a long period of time with a
minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and
regular cleaning.
Before performing any maintenance,
switch off and unplug the tool.
Regularly clean the ventilation slots in your tool
using a soft brush or dry cloth.
Regularly clean the cutting line and spool
using a soft brush or dry cloth.
Regularly use a blunt scraper to remove grass
and dirt from the underneath of the guard.
Do not use any abrasive or solvent-based
cleaner.
Fitting a new spool of cutting line (fig. D)
Replacement spools of cutting line are available
from your Black & Decker dealer (cat. no. A6481).
Unplug the tool.
Keep the tabs (11) depressed and remove the
spool cover (12) from the housing (7).
Remove the empty spool (13) from the housing.
Remove any dirt and grass from the housing.
Take the new spool and unwind approx.
9 cm of cutting line.
Feed the cutting line through the eyelet (14).
Push the spool onto the drive shaft (15) and
rotate it slightly until it is seated. Make sure
that the cutting line is not trapped under the
spool and that 9 cm of cutting line protrudes
from the housing.
Align the tabs on the spool cover with the
holes in the housing.
Push the cover onto the housing until it snaps
securely into place.
If the cutting line protrudes beyond the
trimming blade (6), cut it off so that it just
reaches the blade.
Winding new line onto an empty spool (fig. E)
You may wind new cutting line onto an empty
spool. Replacement packs of cutting line are
available from your Black & Decker dealer
(cat. no. A6170 (25 m), A6171 (40 m)).
Remove the empty spool from the tool as
described above.
Remove any old cutting line from the spool.
Feed 2 cm of cutting line into one of the holes
(16) in the spool as shown.
Bend the cutting line and anchor it in the
L-shaped slot (17).
Wind the cutting line onto the spool in the
direction of the arrow (18). Make sure to wind
the line on neatly and in layers.
Do not criss-cross.
When the wound cutting line reaches the
recesses (19), cut the line. Let the line protrude
approx. 9 cm from the spool and hold a finger
on the line to keep it in place.
Proceed as described above to fit the spool on
the tool.
Only use round 1.5 mm diameter
Black & Decker cutting line. Do not use
Reflex Plus twisted cutting line. The use of
an incorrect type of cutting line can damage
the auto feed mechanism and will void the
warranty.
TROUBLESHOOTING
If your tool seems not to operate properly,
follow the instructions below. If this does not solve
the problem, please contact your local
Black & Decker repair agent.
Before proceeding, unplug the tool.
Tool does not start
Check that the power cables are properly
connected.
Check the mains fuses.
Tool vibrates strongly
Carefully clean the spool housing.
If this does not solve the problem, unwind the
line from the spool and rewind it more tightly.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker GL30 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker GL30 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 0,7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info