584951
13
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
13
ENGLISH
We recommend that you use only one brand
of oil during the lifetime of your chainsaw
because mixtures of different oils could lead to
the oil becoming degraded, which can
drastically shorten the lifetime of the saw chain.
Never use waste oil, thick oil or very thin sewing
machine oil. These may damage your chainsaw.
Fitting the guide bar and chain (fig. B, C & D)
Wear protective gloves.
Place the saw onto a stable surface.
Loosen and remove the chain cover bolt (7)
(fig. C).
Remove the chain cover (6).
Place the chain (9) over the guide bar (8),
making sure that the cutters on the upper part
of the guide bar face towards the front (fig. B).
Guide the chain around the guide bar and pull
it to create a loop at the rear end of the guide
bar.
Place the chain and guide bar onto the saw.
Guide the chain around the drive sprocket (12).
Place the guide bar onto the studs (13). Make
sure that the sliding nut peg (16) locates into
the tensioning hole (17).
Place the chain cover (6) onto the saw.
Fit the chain cover bolt (7) and tighten it finger
tight.
Turn the screw (14) (fig. D) clockwise until the
chain is tight. Make sure that the chain is snug
around the guide bar. Do not overtighten.
Tighten the chain cover bolt using the spanner
supplied.
Checking and adjusting the chain tension (fig. D)
Before use and after every 10 minutes of use,
you must check the chain tension.
Lightly pull on the chain as shown. The tension
is correct when the chain snaps back after
being pulled 3 mm away from the guide bar.
There should be no “sag” between the guide
bar and chain on the underside.
Note: Do not over-tension the chain as this will
lead to excessive wear and will reduce the life of
the bar and chain.
Note: When the chain is new, check the tension
frequently (after disconnecting from the mains)
during the first 2 hours of use as a new chain
stretches slightly.
To increase the tension:
Turn the screw (14) clockwise.
USE
Let the tool work at its own pace. Do not
overload.
Filling oil into the reservoir (fig. E)
Remove the oil cap (3) and fill the reservoir with
the recommended chain oil. You can see the oil
level in the indicator slot (4). Refit the oil cap.
Periodically switch off and check the oil in the
indicator; if it is less than a quarter full,
disconnect your chainsaw from the mains and
refill with the correct oil.
Auto-stop chainbrake (fig. F & G)
This tool is fitted with an auto-stop chainbrake which
will stop the chain within 150 ms each time you
release the rear trigger, or if kickback should occur.
This brake should be tested before every use.
How to set the chainbrake
Make sure that the tool is disconnected from
the mains supply.
Pull the front guard (5) back into the “set”
position .
The tool is now ready to use.
How the anti-kickback chainbrake works
In the event of kickback, your left hand comes in
contact with the front guard, pushing it backwards,
and stops the tool within 150 ms.
How the inertia activated chainbrake works
The chainbrake is activated when the front hand
guard is pushed forward, either manually, by the
back of the users hand or by its own weight. The
advantage of the inertia brake is that it is activated
by a severe kickback, eg. when the chain hits metal,
even if the users hand does not contact the front
guard, ie. when the saw is in the felling position.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker GK1640 T4 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker GK1640 T4 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Black Decker GK1640 T4

Black Decker GK1640 T4 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanôl, Espanõl, Dansk, Svenska, Norsk, Suomi - 128 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info