474484
12
Verklein
Vergroot
Pagina terug
1/104
Pagina verder
12
ENGLISH
If the saw chain or bar becomes jammed:
Switch the tool off.
Disconnect the tool from the mains supply.
Open the cut with wedges to relieve the strain
on the guide bar. Do not try to wrench the saw
free. Start a fresh cut.
Felling (fig. H - J)
Pre-plan a safe exit from falling trees or branches.
Cut one third of the diameter of the tree (Fig. H).
Then cut down from above to make a notch of
about 45°. This way you will avoid pinching the
saw.
Make a single felling cut from the other side
but stop before you cut through to the notch
(fig. I).
Drive a wedge or wedges into the felling cut to
open it and drop the tree (fig. J).
Logging (fig. K - M)
How you should cut depends on how the log is
supported. Use a saw horse whenever possible.
Always start a cut with the chain running and the
spiked bumper (15) in contact with the wood (fig. K).
To complete the cut use a pivoting action of the
spiked bumper against the wood.
When supported along its whole length
Make a downward cut, but avoid cutting the
earth as this will blunt your saw quickly.
When supported at both ends
First, cut one third down to avoid splintering
and second, cut again to meet the first cut.
When supported at one end
First, cut one third up to avoid splintering and
second, cut down to prevent splintering.
When on a slope (fig. L)
Always stand on the uphill side.
When using a saw horse (fig. M)
This is strongly recommended whenever possible.
Position the log in a stable position. Always cut
on the outside of the saw horse arms.
MAINTENANCE (fig. N)
Regular maintenance ensures a long effective life
for the tool. We recommend you make the
following checks on a regular basis.
Oil level
The level in the reservoir should not be allowed to
fall below a quarter full. Top up if low.
Chain and guide bar
After every few hours of use, remove the guide
bar and chain and clean thoroughly.
On reassembling, the guide bar should be
turned through 180° and the sprocket nose
greased via the sprocket lubrication hole (18).
This ensures an even distribution of wear
around the guide bar rails.
TROUBLESHOOTING
If the tool does not operate correctly, check the following.
Fault Possible cause Action
Tool will not start. Blown fuse. Replace fuse.
Tripped RCD. Check RCD.
Mains lead not connected. Check mains supply.
Tool will not start - lock-off
button will not slide. Front guard in the brake position Reset front guard.
Chain does not stop instantly
when the tool is switched off. Chain tension is too slack. Check chain tension.
Bar/chain appear hot/smoking. Oil tank empty. Check oil tank level.
Chain tension is too tight. Check chain tension.
Guide bar sprocket nose needs greasing.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker GK1440 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker GK1440 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,39 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info