585921
10
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
6
D6
To unlock the wheels push the release
button forwards.
D7
Should the lever fully engage on the
ratchet, but the rear wheels not lock into
place, then release the lever, unscrew the
cable adjustment by one turn and re-
engage the lever and ratchet. Repeat
until the wheels fully lock into position.
Your mower will continue to operate whilst
you are pulling the switch lever. To stop your
mower release the switch lever.
When you have finished using your mower
we recommend that you clean all debris from
it before putting it away. Refer to the
‘Care and maintenance’ section.
Note: To obtain the best results cut your
lawn or grass area regularly and do not cut
when the grass is wet.
If, when mowing, loose grass is seen
to be scattering from beneath your mower, the
grassbag is probably full and should be emptied.
Overload protection (GF1838 only)
The GF1838 is fitted with an internal overload
protector which will switch off the motor if the
unit is being used in excessively long grass at
a low height of cut, or if it is being forced into
long grass. If the motor stops in these
conditions there is not a fault with the mower.
It should be left to cool for 10 minutes and
then tilted slightly and run without moving for
1 to 2 minutes. The height of the cut should
be set to maximum and after cutting at that
height be reduced to the desired level.
Manoeuverability (Fig. E)
Your mower has fully rotating wheels and as
such is capable of manoeuvering around
trees posts and other objects. It also allows
accurate mowing of contoured features in
your garden like flower beds.
For maximum manoeuverability release the
rear wheel locking mechanism by pushing
the release button forwards.
When manoeuvering your mower always use
the cable restraint and ensure that the cable
is out of the way of the desired cutting area.
Height of cut adjustment (Fig. F)
Warning! Disconnect your mower from the
electrical supply before making any
adjustment and give the blade time to stop
rotating: the cutting blades are sharp.
F1
Flip the lever outwards and hold it firmly.
Using the lever, rotate the knob to set
the desired height of cut.
Flip the lever back to lock the knob.
F2
To produce a stripe on your lawn, first slide
the striping flap in position and fix with the
2 screws provided, then adjust the height
of cut to a low position (UK only).
Note: For longer or uneven growth lawns
(particularly the first cut of the season) first
use a higher height setting and then finish
with a second cut to the desired length.
Blade maintenance
The steel blade is designed to give a fine finish in
long or tough grass. The blade will continue to
cut even when it has become blunt or burred.
There is no need for it to be razor sharp.
If, however, because of damage or wear the
cutting performance deteriorates, then your
mower may require a new blade, or at least
the existing blade to be sharpened.
We recommend that the steel blade is
sharpened or a new blade fitted at the
beginning of each season.
Replacement blades are available from
Black␣ &␣ Decker service agents.
Warning! When fitting a new blade use only
the Black␣ &␣ Decker replacement part
specified for your mower - do not attempt to
fit any other blade.
Fitting a new blade (Fig. G)
Observe all the relevant warnings before
changing the blade.
Warning! Disconnect your mower from the
electrical supply before changing the blade.
G
Turn your mower over on its side so that
the underside of the cutter cover is
exposed.
Using a cloth placed over the blade or
heavy duty gloves to protect your hands,
grip the blade and, using the spanner
provided, loosen and remove the nut
from the motor spindle. Turn the nut in an
anti-clockwise direction to loosen it.
The blade can now be replaced and the
washer and bolt reassembled.
Note: Do not remove the impeller for any
reason.
Note: Some mowers are fitted with a
clutch washer, between the blade nut and
the blade, which must be reassembled at
all times.
Handy hints
On long grass, above 10cm (4 inches), use two
cuts to get a close finish. We recommend that the
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker GF934 T2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker GF934 T2 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info