709483
12
Verklein
Vergroot
Pagina terug
1/144
Pagina verder
12
ENGLISH
(Original instructions)
After this happens, the charger automatically switches to
the Pack Charging mode. This feature ensures maximum
battery life. The red LED ashes in the pattern indicated on
the label when the Hot/Cold pack delay is detected.
State of Charge Indicator
The battery is equipped with a state of charge indicator.
This can be used to display the current level of charge in the
battery while in the trimmer and during charging. It does not
indicate appliance functionality and is subject to variation
based on product components, temperature and end user
application.
Checking State of Charge during use
u Press the state of charge indicator (A1).
u The four LEDs (A2) will illuminate indicating the percent
of charge in the battery (Fig.A.)
u If LED light does not illuminate, charge battery.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indenitely. The charger will keep the battery
pack fresh and fully charged.
Features
This appliance includes some or all of the following features.
1. Switch box
2. Bail handle
3. Upper-handle
4. Lower-handle
5. Upper-handle attachment levers (2)
6. Lower-handle attachment levers (2)
7. Cut height adjust lever
8. Grass collection bag
9. Rear door cover
10. Battery port
11. Battery storage compartment
12. Carrying handles
13. EdgeMax™
Installing and removing the battery pack
(g. B - C)
u depress the battery port cover release button (14) and pull
the battery port cover (15) up to expose the battery port
(10) as shown in gure B.
u Slide the battery (16) into the battery port until it is fully
seated and an audible click is heard (gure C). Make sure
battery pack is fully seated and fully latched into position.
u Close the battery port cover. Ensure the cover is fully
latched before starting mower.
To remove battery pack (g. D)
u Open the battery port cover (15).
u Depress the battery release button (17) on the battery
pack and pull battery pack out of tool as shown in gure D.
Battery storage
An extra battery can be stored using the battery storage
compartment (11).
u Lift the storage compartment cover and slide the battery
into the compartment as shown in gure E. Battery in this
compartment will not actuate the mower.
u Screw the upper handle quick release clamps (7) through
the lower handle into the clamp nuts (20), With the
upper handle quick release clamps screwed in half way,
close the quick release clamps (g. G). If the connection
between the handle and quick release clamps is too tight
or loose, adjust the depth of the quick release clamps and
close them again until the teeth are fully closed.
Assembly
Warning! Before assembly, make sure that the tool is
switched off and the safety key and battery have been
removed.
Attaching lower handle (g. F)
u lift lower handle (4) into place making sure the arrow (18)
on the base of the mower lines up with 1, 2, or 3 on the
base of the handle (19) (inset of gure F).
Note! Ensure each side of the lower handle is set on the
same number. The arrow must be lined up with 1, 2, or 3 for
operation.
u Close the handle height adjust levers (7) as shown in
gure F. As you close each, make sure the teeth are
engaged as shown in gure G.
u If the connection between the handle and lever is too tight
or loose, open the lever and adjust the depth of the lever
by turning the lever. Close it again until the teeth are fully
clasped and each lever stays securely closed.
Attaching upper handle (g. H)
u Remove the upper-handle attachment levers (5), nuts
(20), and washers (21) from the handle.
u Line up the holes on the bottom of the upper handle (3)
with the holes on the top of the lower handle (4).
Note: Make sure the cord is located on the front of both
handles. If it is not it may result in the cord tangling and the
inability to easily store the mower (g. I)
u From the outside of the upper handle (3), slide the lever
bolt through the holes.
u Slide the washer over the bolt of the lever and loosely
assemble the entire assembly with the nut.
u Rotate the upper handle into its operating position.
u Close the lever. If it is too tight or too loose, open the lever
and the nut to adjust the clamping. Check the levers by
closing them. They should be tight enough so the handles
are held rmly, but loose enough so the levers can be fully
closed. Adjust by opening the lever and turning the nut
until the handles are secured.
Securing the motor cable (g. J)
Warning: Attach cable so that it does not become stretched or
pinched in the joints of the handles during use or folding. This
can cause damage to the cord.
The motor cable (22) has to be xed to the handles using the
cable restraints (23) that are already attached to the handle to
clip the cable to the handle:
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker CLMA4820L2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker CLMA4820L2 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 8,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info