792731
8
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
8
ENGLISH (Original instructions)
To install battery pack (g. B)
uInsert battery (4) into tool until an audible click is heard as
shown in gure B.
uEnsure battery pack is fully seated and fully latched into
position.
To remove battery pack
uDepress the battery release button and pull battery pack
(4) out of the tool.
Assembly (Fig. C)
uAlign the top of the extension tube (9) with the vacuum
inlet (16) as shown in gure C.
uPush the extension tube (9) onto the vacuum inlet (16) so
it locks into position.
uAlign the bottom of the extension tube (9) with the oor
head (8) as shown in gure C.
uPush the bottom of the extension tube (9) onto the oor
head (8) so it locks into position.
uTo remove an accessory, press the accessory release
latch located on the accessory and pull it off.
USE
This vacuum cleaner can be used in one of four ways.
uWith the extension tube (9) and the oor brush (8) as
shown in gure C.
uWith the oor brush (8) and the vacuum inlet (16) as
shown in gure D.
uWith the extension tube (9) and an accesssory tool (10),
(11), (13) or (14) as shown in gure E.
uWith an accesssory tool (10), (11), (13) or (14) and the
vacuum inlet (16) as shown in gure E.
uAccessories not supplied with your unit can be ordered
through service department.
Switching ON and OFF (Fig. F)
uTo switch ON, press the On/Off button (1).
uFor increased power, slide the variable power switch (2)
forward.
Note: The oor brush (8) will power on when it is
attached to the vacuum or extension tube (it can be switched
off by pressing the button 2a on the display). The LED
worklights on the front of the oor head will illuminate
whenever the beater bar activation button (2a) is switched ON
(they can be switched off by pressing the button again).
Note: The state of charge indicator LEDs (3) will
illuminate while the vacuum is ON.
uTo switch OFF, press the On/Off button (1).
uReturn the battery to the charger immediately after use so
that it will be ready and fully charged for the next use.
Using an Accessory tool (Fig. G)
Your vacuum may come with some of the following tools.
u2 in 1 Accesssory tool (10)
uCrevice tool (11).
uPet hair tool (13).
uWide mouth dust brush (14).
uThe accessory tool (10), (11), (13) or (14) can be tted
either directly to the extension tube (6) or to the vacuum
inlet (5) as shown in Fig. G.
uAlign the top of the accessory tool (10), (11), (13) or (14)
with the vacuum inlet (16) or extension tube connection
(9a) and push into place so it locks into position as shown
in gure G.
Cleaning and emptying the vacuum
Filter agitator (Fig. H)
With the lift away dust canister (6) off the chassis (17) ,
rotate the lter agitator wheel 5 - 10 times to remove exces-
sive dust from the lter thus increasing its performance.
Note: It is recommended that you agitate when the unit is
emptied and the prelter removed.
Note: Maximum dust collection will only be obtained with
clean lters and an empty dust canister.
If dust begins to fall back out of the product after it is switched
off, this indicates that the dust canister is full and requires
emptying.
To empty the dust canister (Fig. I, J)
uLift and remove the lift away dust canister (6) from the
chassis (17) as shown in gure I.
uPlace the dust canister over a dust bin and press the
dust canister lid release button (6a) to empty the dust
canister as shown in gure J.
uClose the dust canister lid (7), until it “clicks” rmly
into position.
uInstall the lift away dust canister (6) back onto the
chassis (17).
Removing pre-lter (Fig. K)
uLift and remove the lift away dust canister (6) from the
chassis (17) as shown in gure I.
uPlace the dust canister over a trash bin and press the
dust canister lid release button (6a) to empty the dust
canister as shown in gure J.
uUse your index nger and thumb to pinch the pre-lter
(18), pull the pre-lter (18 ) from the dust canister (6) as
shown in gure K.
Note: The lter housing ts snuggly in the dust canister
and may be difcult to remove at rst.
uEmpty the dust canister.
uInstall the pre-lter (18) into the dust canister (6)
ensuring the dust canister tab (20) aligns with the prelter
slot (19) as shown in gure K.
uInstall the dust canister onto the vacuum, until it “clicks”
rmly into position.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker BHFEV36B2D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker BHFEV36B2D in de taal/talen: Engels als bijlage per email.

De handleiding is 1.59 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info