Handleiding Black Decker BHFEV362DA (pagina 9 van 76) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins)

743303

Verklein

Vergroot

Pagina terug

1/76

Pagina verder

ENGLISH

(Original instructions)

u Align the top of the accessory tool (10), (11), (13) or (14)

with the vacuum inlet (16) or extension tube connection

(9a) and push into place so it locks into position as shown

in gure G.

14 Wide mouth dust brush √

10 2 in 1 Accessory √√√

11 Crevice tool

12 Accessory storage clip √√√

13 Pet hair tool √

BHFEV362D

u All available through service department.

Cleaning and emptying the vacuum

Filter sense

Whenever a lter is Blocked and needs cleaning, the red

lter LED (3) in the chassis will illuminate.

Filter agitator (Fig. H)

With the lift away dust canister (6) off the chassis (17) ,

rotate the lter agitator wheel 5 - 10 times to remove exces-

sive dust from the lter thus increasing its performance.

Note: It is recommended that you agitate when the unit is

emptied and the prelter removed.

Note: Maximum dust collection will only be obtained with

clean lters and an empty dust canister.

If dust begins to fall back out of the product after it is switched

off, this indicates that the dust canister is full and requires

emptying.

To empty the dust canister (Fig. I, J)

u Lift and remove the lift away dust canister (6) from the

chassis (17) as shown in gure I.

u Place the dust canister over a dust bin and press the

dust canister lid release button (6a) to empty the dust

canister as shown in gure J.

u Close the dust canister lid (7), until it “clicks” rmly

into position.

u Install the lift away dust canister (6) back onto the

chassis (17).

Removing pre-lter (Fig. K)

u Lift and remove the lift away dust canister (6) from the

chassis (17) as shown in gure I.

u Place the dust canister over a trash bin and press the

dust canister lid release button (6a) to empty the dust

canister as shown in gure J.

u Use your index nger and thumb to pinch the pre-lter

(18), pull the pre-lter (18 ) from the dust canister (6) as

shown in gure K.

Note: The lter housing ts snuggly in the dust canister

and may be difcult to remove at rst.

u Empty the dust canister.

u Install the pre-lter (18) into the dust canister (6)

ensuring the dust canister tab (20) aligns with the prelter

slot (19) as shown in gure K.

u Install the dust canister onto the vacuum, until it “clicks”

rmly into position.

Removing lter (Fig. L)

u Lift and remove the lift away dust canister (6) from the

chassis (17) as shown in gure I.

u Place the dust canister over a trash bin and press the

dust canister lid release button (6a) to empty the dust

canister as shown in gure J.

u Grasp the agitator wheel housing (21) and pull up

to remove.

u Remove the lter (22), from the agitator wheel housing

(21) as shown in gure L.

u Shake off or lightly brush any loose dust from the lter.

u Install the the lter (22), into the agitator wheel

housing (21).

u Install the agitator wheel housing (21) onto the dust

canister, until it “clicks” rmly into position.

Cleaning the lters

u Once the lter and pre-lter are removed from the dust

canister shake off or lightly brush any loose dust from

the pre-lter and lter.

u Rinse out the dust canister (6) with warm soapy water.

u Wash the lters with warm soapy water.

u Ensure the lters are completely dry before retting

(24hrs).

u Follow instructions in the “Removing pre-lter and

Removing lter” sections for assembly instructions.

Note: Maximum dust collection will only be obtained with

clean lters and an empty dust canister.

If dust begins to fall back out of the product after it is

switched off, this indicates that the dust canister is full

and requires emptying or that there is a blockage somewhere.

u Wash the lters regularly using warm, soapy water and

ensure that it is completely dry before using again. The

cleaner the lter is, the better the product will perform.

u It is very important that the lters are completely dry

and correctly in position before use.

Removing and clearing the rotary brushes

(Fig. M)

Warning! To reduce the risk of injury from moving parts,

disconnect battery before cleaning or servicing.

u To remove the rotary brush (23) from the oor head (8)

depress the release button (24) as shown in gure M.

u Lift the rotary brush from its locked position.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Black Decker BHFEV362DA Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info