Handleiding Black Decker BEMWH551 (pagina 11 van 132) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins)

709479

Verklein

Vergroot

Pagina terug

1/132

Pagina verder

ENGLISH

(Original instructions)

6. Lower handle

7. Motor cover

8. Lower handle latch

9. Blade bolt spanner

Assembly

Warning! Before assembly, make sure that the appliance is

switched off and unplugged.

Attaching the lower handle to the main body

(Fig. A)

u Align the holes on the lower handle (6) with the holes on

the main body (8a).

Insert the lower handle latch (8) and push until secure as

shown in gure A.

Attaching the upper handle to the lower handle

(Fig. B)

u Align the holes on the lower handle (6) with the

corresponding holes on the upper handle (1).

u Insert the screw (5b) through both handles and t the

washer (5a).

u Place the upper handle latch (5) onto the screw (5b) and

tighten until secure as shown in gure B.

Note: The upper handle can be attached to the lower handle

with the upper handle latch (5) located either on the outside or

the inside, depending on personal preference.

Before starting

u Before use, check that the mower is in good

working order.

u Ensure the power button is in the off position and

disconnect the cable plug from the mains supply.

u Examine the general condition of the mower.

Inspect the body underneath the deck, blade,

switch, power cord and extension cord (if used).

u Check for loose screws, misalignment, binding

of moving parts, improper mounting, broken

parts and any other condition that may affect

its safe operation.

u If abnormal noise or vibration occurs during operation,

turn the mower off immediately and have the problem

corrected. Do not use a damaged tool and attach a label

“DO NOT USE” to the tool. Ensure that you are on a at

surface and have secure footing. Check that the

latches (5, 8) are securely tightened.

Switching on and off (Fig. C, D)

Note: Practise switching on and switching off the mower as

detailed below before using it to cut grass for the rst time.

Start the mower on a hard, level surface (such as a driveway)

that is free of debris. Connect the power cordset to the power

point.

u Squeeze the motor on/off grip (2) towards the upper

handle (1) and use the other hand to press the power

button (3) as shown in gure C. The power button remains

depressed as long as the pressure is maintained on the

motor on/off grip (2).

u Transfer the other hand to the upper handle (1). As

the motor picks up speed, the mower lifts on a cushion

of air, making it very light to handle and extremely

manoeuvrable. To stop the motor, release pressure on the

motor on/off grip (2) until the power button (3) clicks off.

The mower sinks to the ground. The motor is not

started if pressure is re-applied to the motor on/off grip (2)

alone. It is necessary to squeeze the motor on/off grip (2)

and re-press the power button (3) to re-start the motor.

Emergency stop

u To stop the motor in an emergency, simply release the

pressure on the motor on/off grip.

u Keep your hands on the upper handle in order to control

the mower as it sinks to the ground.

u Allow the motor to stop completely before releasing

control of the handle.

Changing the mower blades (Fig. E, F)

Warning! Never carry out any assembly operations or

adjustments with the power connected to the mower. Always

ensure that the power button is in the off position and that the

power plug is disconnected from the supply.

Periodically check the blades (11) for damage and balance.

If there are broken ends or other damage or the two blades

are out of balance they must both be replaced.

With the power button (3) in the off position and the power

plug removed from the supply, turn the mower on its back as

shown in gure E.

u Unclip the old blades (11) from the pins (12) and replace

them with new ones.

u Return the mower to the upright position.

u Reconnect the power cable to the supply and run the

mower for a few minutes to check that the blades are

properly tted and that there is no undue noise or

vibration.

u Use only blades as recommended by the manufacturer.

To change from a 28mm to a 38mm cut (Fig.G, H, I)

u Use the blade bolt spanner (9) to remove the blade bolt

(9a).

u Remove the blade holder disc (10) and replace it the other

way around.

u Remove the blades (11) from their anchor pins (12) on the

underside of the blade holder disc (10).

u Replace the blades on the anchor pins on the upper side

of the blade holder disc (10).

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Black Decker BEMWH551 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info