Handleiding Black Decker BDPS600 T1 (pagina 11 van 128) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins)

578630

Verklein

Vergroot

Pagina terug

1/128

Pagina verder

ENGLISH

(Original instructions)

Two speed control switch (g. H) (BDPS600 only)

Your sprayer has two different speed settings.

u To change speeds, press the speed control switch (9). An

LED indicates setting 1 or 2.

u Set the ow control knob (8) to a lower or medium settting

(1-5) when on speed setting 1.

u Set the ow control knob (8) to medium or higher setting

(5-9) when on speed setting 2.

Use the lower speed setting (Setting 1) to obtain greater con-

trol over your spraying project, while the higher speed (Setting

2) allows for greater coverage in a shorter amount of time.

The lower speed level allows you to get closer to your work

with less overspray. Low setting works well with lighter bodied

or more free owing paints like stains and sealers.

More heavy bodied paints, like water based latex, will need

setting number 2

Use the speed control setting in conjuction with the ow

control knob and test for what works best with your material

being sprayed.

Flow control knob (g. I)

The ow control knob regulates the amount of liquid that can

be sprayed.

u Turn the ow control knob (8) clockwise to increase the

ow of liquid

u Turn the ow control knob (8) counterclockwise to

decrease the ow of liquid.

Note : Always test the spray pattern on scrap cardboard

or similar material rst. Begin with ow control knob on the

highest ow setting. If less ow is desired, dial the ow control

knob in. Heavier, thicker materials should be sprayed with the

higher settings 7 - 9. Thinner materials should be sprayed with

the lower settings 1 -3.

Note : If the ow control setting is set completely to the

minimum side, the trigger will have limited or no travel. Back

the ow control knob off (clockwise) to allow for more trigger

travel.

Direct to tin hose (g. J & K) (BDPS600 only)

It is possible to use the BDPS600 with out the side ll canister.

When using the supplied 'direct to tin hose' you can take the

paint supply directly from the paint tin.

u Remove the sidell canister (6), pickup tube (19) and lter

(25).

u Push the suction hose onto the intake (30) and return (29)

ports.

u Pull the hose apart on the opposite end and slide the

larger hose (17) completely through the container clip

(18), then over the barbs (22) of the pickup tube (19).

u Place the suction tube assembly into the material con-

tainer and attach the container clip securely to the side.

Check to make sure that complete assembly is submerged

in the material container.

Liquid material preparation (g. L & M)

Note : Make sure the type of material you use can be cleaned

with either mineral spirits or paint thinner (for oil-based paints)

or a warm water and soap solution (for water soluble paints

like latex). Use drop cloths to protect your oors and anything

else in the spraying area that you wish to remain untouched.

The liquid being sprayed may need to be thinned (diluted)

before staring. When thinning, use the proper liquid thinner

recommended on the container by the material manufacturer.

Warning! Do not use materials with a ashpoint lower than

55°C.

Note : A mixing bucket (12) is provided (BDPS600 only)to use

when transferring spray material from the original container

into the bucket for thinning and measuring purposes (g. L).

Note : A viscosity cup (13) is provided to determine the

“runout time” of the material being used.

u Before measuring for the proper viscosity, stir the material

thoroughly.

u Dip the viscosity cup (13) into the material being sprayed

and ll the viscosity cup (13) completely.

u With the viscosity cup (13) held over the material con-

tainer, measure the amount of time it takes for the stream

of material owing out to “break” or stop being a constant

stream out of the bottom of the viscosity cup (13) (2

minutes or less) (g. M). This is the “runout time” Refer to

the thinning table for information on the thinning required

for different materials.

u If material needs thinning, add the appropriate liquid thin-

ning material recommended by the manufacturer.

u It is possible to spray latex paint with this unit, however

the paint may require thinning. In some cases the paint

may require thinning beyond the paint manufacturers

recommendations, please consult the paint manufacturers

instructions. If a paint is found to be too thick and will not

spray, thin the paint using the appropriate thinning mate-

rial. Thinning material should be added at a ratio of 5% of

the volume of paint until the paint ows through the paint

gun providing an even and satisfactory nish.

Thinning table

Spray material Runout time

Clear and semi-transparent stains

and sealers

No thinning required

Oil based primers, varnishes and

polyurethane

(Less than 2 minute runout)

Solid colour water based stains May require thinning

Water based or latex paints (More than 2 minute runout)

Note : Not recommended for textured paint

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Black Decker BDPS600 T1 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Black Decker BDPS600 T1

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info