578621
7
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
7
ENGLISH
(Original instructions)
Attaching the roller head (g. B)
u Slide the handle assembly (12) into the roller head (7) en-
suring that the O-ring (13) is seated inside the roller head
(7) and the black collar (14) meets the roller head (7).
u Thread the black collar (14) onto the threads of the roller
head (7) and tighten.
Attaching a roller to the roller head (g. C)
u Lubricate the tips (15) at either end of the roller frame (16)
using petroleum jelly.
u Slide the assembled roller (8) onto the roller frame (16).
Note: Make sure the roller assembly snaps into the locking
clip on the outer end cap of the roller.
Attaching the drip tray (g. D)
The drip tray helps reduce spatter and drips when painting,
especially on ceilings.
u Clip the drip tray (9) onto the roller frame (16) so that it ts
around the roller (8).
u Rotate the drip tray to the required position.
Note: The drip tray is also helpful to prevent dripping when the
Speedy Roller
TM
is resting on the kickstand and is not in use.
Position the drip tray under the roller.
Use
Filling with paint (g. E & F)
Note: When using the Speedy Roller
TM
for the rst application,
it will take most of the paint in the paint reservoir to saturate
the roller cover. A second ll may be needed.
u Insert the small end of the ll tube (17) through the hole in
the bottom side of the paint can clip (18). Push gently until
it click into place.
u Place the paint can clip (18) over the edge of your paint
can.
Note: For deeper containers, t a section of 19mm inner
diameter clear tubing over the ribs of the ll tube to extend it
and clip to side of pail with ll tube can clip. Cut the bottom
end of the tubing at a slight angle. Tubing is available at most
DIY stores.
u Lubricate the top of the ll tube (17) with a small amount
of petroleum jelly.
u Hold the Speedy Roller
TM
at a 45
O
angle and place the ll
valve (5) over the ll tube (17). Gently push the Speedy
Roller
TM
down so it completely covers the ll tube.
Note: Make sure the orange ll cap cover (19) is com-
pletely covered by the shroud of the can clip.
u Very rmly pull the plunger (1) all the way back to draw
paint into Speedy Roller
TM
ensuring you apply sufcient
pressure to maintain an adequate union between the ll
valve and ll tube.
u Lift the Speedy Roller
TM
slowly off the ll tube.
Note: If you do not receive a complete ll the rst time, push
the plunger slowly to return paint to can and then pull the back
plunger making sure the angle is correct and the orange ll
cap cover is fully seated.
Adjusting the angle of the roller head (g. G & H)
The roller head can be adjusted to three different angles.
u Press and hold the orange head ratation button (6) on the
roller head (7).
u Rotate the rollerhead (7) to the required angle.
Note: Use straight on for general painting and 40
O
or 80
O
angles for hard to reach places or when painting close to
ceiling or edging.
Note: The handle (10) can be rotated to make it more comfort-
able when painting with an angled roller frame. To rotate
handle to desired position, loosen collar (11), adjust handle
and retighten collar (g H).
Painting with the Speedy Roller
TM
(g. I & J)
u Begin rolling on wall and push plunger handle (1) or
squeeze trigger (2) to feed paint into the roller cover.
Note: Initial saturation of the roller may require the full amount
of paint from the rst ll. Fill Speedy Roller
TM
as needed.
Helpful hints
u The trigger only needs to be squeezed when paint is
needed.
u If you are getting a dot pattern when painting, apply more
paint.
u If the roller is sliding on the surface, apply less paint.
u You may notice petroleum jelly within the handle. This is
necessary and will help in its operation and will not affect
the paint.
u When not in use, rest the Speedy Roller
TM
on the kick-
stand (4) with the drip tray (9) attached and positioned
under the roller..
Returning excess paint to paint tin (g. K - M)
u Place thumb over orange ll cap cover (19).
u Pull plunger (1) back to draw excess paint from roller
frame into tube.
u Hold the Speedy Roller
TM
at a 45
O
angle and place the ll
valve (5) over the ll tube (17). Gently push the Speedy
Roller
TM
down so it completely covers the ll tube.
Note: Make sure the orange ll cap cover (19) is com-
pletely covered by the shroud of the can clip.
u Push the plunger all of the way into the tube.
u Remove the roller (8) by grasping the outer end cap (20)
and the roller frame (16) and using your thumb on the
opposite hand to push the roller off
Note: Wear disposable gloves or use a plastic bag over roller
to keep your hands clean.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker BDPR400 T1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker BDPR400 T1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,02 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Black Decker BDPR400 T1

Black Decker BDPR400 T1 Gebruiksaanwijzing - Polski - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info