709498
6
Verklein
Vergroot
Pagina terug
1/79
Pagina verder
10
ENGLISH
(Original instructions)
11
ENGLISH
(Original instructions)
in an air temperature below +4.5 °C), or above +40 °C.
This is important and will prevent serious damage to the
battery pack.
u The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
u If the battery pack does not charge properly:
u Check operation of receptacle by plugging in a lamp
or other appliance;
u Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
u Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 18 °C – 24 °C;
u If charging problems persist, take the tool, battery
pack and charger to your local service center.
u The battery pack should be recharged when it fails to
produce sufcient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse effect on the battery pack.
u Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Unplug the
charger before attempting to clean.
u Do not freeze or immerse the charger in water or any
other liquid.
Fitting and removing the battery (g. C, D)
u To t the battery (8), line it up with the receptacle on the
tool (7). Slide the battery into the receptacle and push until
the battery snaps into place.
u To remove the battery, push the battery release button
(8a) while at the same time pulling the battery out of the
receptacle.
Assembly
Warning! Before assembly, make sure that the tool is
switched off and the battery is removed.
Fitting and removing the guard (g. E, F, G)
The tool is supplied with a guard intended for grinding
purposes only (type 27). If the unit is intended to perform
cutting off operations, a guard specic for this operation (type
41) must be tted. Suitable guard part number 1004702-44
(for 125mm cutting wheel) are available and can be obtained
from BLACK+DECKER service centres.
u Place the tool on a table, with the spindle (11) facing up.
u Release the clamping lock and hold the guard over
the tool as shown in gure E.
u Align the lugs (5a) with the notches (10) as shown in
figure F.
u Press the guard down and rotate it counterclockwise to
the required position as shown in figure G.
u Tighten the guard latch screw to secure the guard to the
tool.
u If required, tighten the screw to increase the clamping
force.
Removing
u Release the guard latch screw.
u Rotate the guard clockwise to align the lugs (5a) with the
notches (10).
u Remove the guard from the tool.
Warning! Never use the tool without the guard.
Fitting the side handle
u Screw the side handle (3) into one of the mounting holes
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding discs, cutting discs
or sanding ap pads (g. H, I, J, K, L)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size (see
technical data).
Fitting
u Fit the guard as described above.
u Place the inner ange (12) onto the spindle (11) as shown
in gure. H. Make sure that the ange is correctly located
on the at sides of the spindle.
u Place the disc (6) onto the spindle (11) as shown in gure
H. If the disc has a raised centre, make sure that the
raised centre faces the inner ange.
u Make sure that the disc locates correctly on the inner
ange.
u Place the outer ange (14) onto the spindle. When tting
a grinding disc, the raised centre on the outer ange must
face towards the disc (A in g. I). When tting a cutting
disc, the raised centre on the outer ange must face away
from the disc (B in g. I).
u Keep the spindle lock (4) depressed and tighten the outer
ange using the two-pin spanner (16) (g. J).
Removing
u Keep the spindle lock (4) depressed and loosen the outer
ange (14) using the two-pin spanner (16) (g. J).
u Remove the outer ange (14) and the disc (6).
Surface grinding with grinding discs
u Allow the tool to reach full speed before touching the tool
to the work surface.
u Apply minimum pressure to the work surface, allowing the
tool to operate at high speed.
Grinding rate is greatest when the tool operates at high
speed.
u Maintain a 20˚ to 30˚ angle between the tool and work
surface as shown in gure L.
u Continuously move the tool in a forward and back motion
to avoid creating gouges in the work surface.
u Remove the tool from work surface before turning tool off.
Allow the tool to stop rotating before laying it down.
Edge grinding with grinding discs
Wheels used for cutting and edge grinding may break or kick
back if they bend or twist while the tool is being used to do
cutoff work or deep grinding.
Edge grinding/ cutting with a Type 27 wheel must be limited to
shallow cutting and notching, less than 13 mm in depth when
the wheel is new. Reduce the depth of cutting/notching equal
to the reduction of the wheel radius as it wears down. Refer to
the 'Grinding and cutting accessory chart' at the end of ths
manual for more information.
Edge grinding/cutting with a Type 41 wheel requires usage of
a Type 41 guard.
u Allow the tool to reach full speed before touching the tool
to the work surface.
u Apply minimum pressure to the work surface, allowing the
tool to operate at high speed. Grinding rate is greatest
when the tool operates at high speed.
u Position yourself so that the openunderside of the wheel is
facing away from you.
u Once a cut is begun and a notch is established in the
workpiece, do not change the angle of the cut. Changing
the angle will cause the wheel to bend and may cause
wheel breakage. Edge grinding wheels are not designed
to withstand side pressures caused by bending.
u Remove the tool from the work surface before turning the
tool off. Allow the tool to stop rotating before laying it
down.
Warning! Do not use edge grinding/cutting wheels for surface
grinding applications if the wheel label has forbidden such use
because these wheels are not designed for side
pressures encountered with surface grinding. Wheel breakage
and serious personal injury may result.
Fitting and removing sanding discs (g. K)
For sanding, a backing pad is required. The backing pad is
available from your BLACK+DECKER dealer as an accessory.
Fitting
u Place the inner ange (12) onto the spindle (11) as shown
(g. K). Make sure that the ange is correctly located on
the at sides of the spindle.
u Place the backing pad (18) onto the spindle.
u Place the sanding disc (19) onto the backing pad.
u Place the outer ange (14) onto the spindle with the raised
centre facing away from the disc.
u Keep the spindle lock (4) depressed and tighten the outer
ange using the two-pin spanner (16) (g. J).
Make sure that the outer ange is tted correctly and that
the disc is clamped tightly.
Removing
u Keep the spindle lock (4) depressed and loosen the outer
ange (14) using the two-pin spanner (16) (g. J).
u Remove the outer ange (14), the sanding disc (19) and
the backing pad (18).
Surface nishing with sanding discs
u Allow the tool to reach full speed before touching the tool
to the work surface.
u Apply minimum pressure to work surface, allowing the tool
to operate at high speed. Sanding rate is greatest when
the tool operates at high speed.
u Maintain a 5˚ to 10˚ angle between the tool and work
surface as shown in gure M.
u Continuously move the tool in a forward and back motion
to avoid creating gouges in the work surface.
u Remove the tool from work surface before turning tool off.
Allow the tool to stop rotating before laying it down.
Using sanding backing pads
Always choose the proper grit sanding discs for your
application. Sanding discs are available in various grits.
Coarse grits yield faster material removal rates and a rougher
nish. Finer grits yield slower material removal and a
smoother nish. Begin with coarse grit discs for fast, rough
material removal. Move to a medium grit paper and nish with
a ne grit disc for optimal nish.
u Coarse = 16 - 30 grit.
u Medium = 36 - 80 grit.
u Fine Finishing = 100 - 120 grit.
u Very Fine Finishing = 150 - 180 grit.
u Allow the tool to reach full speed before touching tool to
the work surface.
u Apply minimum pressure to work surface, allowing the tool
to operate at high speed. Sanding rate is greatest
when the tool operates at high speed.
u Maintain a 5˚ to 10˚ angle between the tool and work
surface as shown in gure N. The sanding disc should
contact approximately 25mm of work surface.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker BCG720 M1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker BCG720 M1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 21,75 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info