Solutions. Todos los derechos reservados. Distribuido por Sunbeam Products,
Inc. operando bajo el nombre de Jarden Consumer Solutions, Boca Raton,
Florida 33431.
Printed in China/Impreso en China
HEATER SAFETY
PLEASE READ AND SAVE
THESE IMPORTANT
SAFEGUARDS
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock, and injury to persons, including the following:
1. Read all instructions before using the appliance.
2. To avoid fire or shock hazard, plug the appliance directly into
a 120V AC electrical outlet.
3. The heater is hot when in use. To avoid burns, DO NOT
let bare skin touch hot surfaces. Use handle when moving
this heater. Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes, and curtains at least 3
ft (0.9 m) from the front of the heater and keep them away
from the sides and rear.
4. DO NOT run cord under carpeting. DO NOT cover cord with
throw rugs, runners, or the like. Arrange cord away from
traffic area and where it will not be tripped over.
5. This heater is not intended for use in bathrooms, laundry
areas and similar indoor locations. NEVER locate heater
where it may fall into a bathtub or other water container.
6. Extreme caution is necessary when any heater is used by,
or near children or invalids, and whenever the heater is left
operating and unattended.
7. Always unplug the heater when not in use.
8. When unplugging, be sure to pull by the plug and not the
cord.
9. DO NOT insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an electric
shock or fire, or damage the heater.
10. DO NOT operate heater with a damaged cord or plug, or
after the heater malfunctions, or has been damaged in any
manner. Return appliance to manufacturer for examination,
electrical or mechanical adjustment, or repair.
11. A heater has hot and arcing or sparking parts inside. DO
NOT use it in areas where gasoline, paint, or flammable
liquids are used or stored.
12. Use appliance only for intended household use as described
in this manual. Any other use not recommended by the
manufacturer may cause fire, electric shock, or injury to
persons. The use of attachments not recommended or sold
by the manufacturer may cause hazards.
13. DO NOT use outdoors.
14. To prevent a possible fire, DO NOT block air intakes or
exhaust in any manner. DO NOT use on soft surfaces like a
bed, where openings may become blocked.
15. To disconnect heater, turn unit Off, then remove plug from
outlet.
16. Avoid the use of an extension cord because the extension
cord may overheat and cause a risk of fire. However, if you
have to use an extension cord, the cord should be No.
14AWG minimum size and rated not less than 1875 watts.
17. If the heater will not operate, see specific instructions under
Auto Safety Shut-off on resetting the heater.
18. DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void your
warranty. The inside of the unit contains no user serviceable
parts. All servicing should be performed by qualified
personnel only.
19. DISCONTINUE USE IF PLUG OR OUTLET IS HOT.
RECOMMEND OUTLET BE REPLACED IF PLUG OR
OUTLET IS HOT TO TOUCH.
PLEASE SAVE THESE
INSTRUCTIONS
CONSUMER SAFETY INFORMATION
THIS APPLIANCE HAS A POLARIZED
PLUG (one blade is wider than the other).
To reduce the risk of electric shock, this
plug is intended to fit in a polarized outlet
only one way. If the plug does not fit fully
in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician
to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR
DEFEAT THIS SAFETY FEATURE IN ANY WAY.
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
TECHNICAL SPECIFICATIONS
Amps: 12.5
Wattage: 1500W/ (+ 5% - 10%)
Working Voltage: 120V AC/60 HZ
Bulb Type: (2) 25W max Candelabra Base
Avoid overloading your circuit by not using other high
wattage appliances in the same outlet. At 1500 Watts,
this unit draws 12.5 Amps.
ASSEMBLY INSTRUCTIONS
Please make sure to check packaging for parts that
could be used to operate your heater.
This package includes:
1 - Fireplace Heater 2 - Light bulbs
1 - Remote Control 2 - AAA Batteries for Remote Control
1 - Stand 4 - Machine Screws (for stand)
1 - Wall Mount Hardware Kit
Installing Batteries into the Remote:
Before operation, insert 2 “AAA” batteries into the back of
the remote control:
• Do not mix old and new batteries
• Do not mix alkaline, standard (carbon-zinc), or
rechargeable (nickel-cadmium) batteries
The remote control for this unit has the capability of
remote will not work through walls.
Bulb Installation:
Unwrap the two 25W Candleabra Bulbs from foam
packaging material and open doors on back of unit with a
flathead screwdriver.
(Front of Heater)
(Back of Heater)
Fig. 2
Fig. 1
KEY TO ICONSREMOTE CONTROL
CONTROL PANEL
On/Off
Thermostat
Timer
Flame Brightness
Sound
Fahrenheit/Celsius
OPERATING INSTRUCTIONS
• There may be an odor coming from the heater the
first time you use it. This is normal during the break-in
period or after long term storage. Make sure the heater
is in a well ventilated area and continue running it until
the smell goes away.
• You may hear a popping or crackling sound as the
heater heats up. This is normal and safe operation.
• The Fireplace Heater can be operated by using the
remote control (Fig. 1) or the control panel (Fig. 2)
located on the top of the unit.
• Place the heater on a rm, level surface or mount on
wall.
• Avoid overloading your circuit by not using other high
wattage appliances in the same outlet. At 1500 Watts,
this unit draws 12.5 Amps.
(Front of Heater)
(Back of Heater)
Power On/Off
First button push will illuminate LCD and power light. The
units default settings are: Temperature 80°; Timer OFF;
Flame Brightness HIGH; Sound ON. After turning th unit
Off, the fan will continue to run for 10 seconds to cool unit
down.After all settings are chosen, LCD will go dark.
(Front of Heater)
(Back of Heater)
Thermostat
• Press Thermostat button until desired temperature level
appears on LCD Display. It is recommended to start by
setting the temperature to the highest setting. Note: the
fan will continue to run for flame operation without heat.
• The system now maintains the selected comfort level
by automatically turning the heater ON and OFF. The
Thermostat
(Front of Heater)
(Back of Heater)
cycles ON and OFF with the heater
element as it maintains the programmed temperature.
• When LCD reads 00the heat will turn off but the fan will
continue to run for flame operation.
(Front of Heater)
(Back of Heater)
Timer
You can set the timer to automatically turn the unit off.
Press the Timer button, select between 1 and 12 hours.
Your selection will then be displayed on the LCD
(Front of Heater)
(Back of Heater)
Flame Brightness
There are four flame brightness settings: HIGH, MEDIUM,
LOW, OFF. Press button to select desired brightness.
(Front of Heater)
(Back of Heater)
Sound
Press Sound button to turn crackling sound on or off. The
sound volume can be adjusted to 4 levels and turned off.
Push the button to cycle through. To turn the sound off
immediately hold the sound button for two seconds and
release.
(Front of Heater)
(Back of Heater)
Fahrenheit/Celsius
Press to show temperature in Fahrenheit or Celsius.
Wall Mounting Template
To mount into wall studs
1. Find studs in wall. Studs are typically 16” apart.
2. Cut Mounting Template on dotted line and tape onto wall so
brackets are centered on studs.
3. Use level to make sure template is level. Using a sharp object
such as an awl, mark hole location.
4. Using a Power Driver with Phillips head bit, drive 1.5” screws
through bracket and drywall into wood or metal stud.
IMPORTANT: Before drilling into any wall ensure no
electrical cables are present in the area.
To mount into drywall
Use toggle bolts for 3/8 - 5/8” thick drywall.
1. Cut Mounting Template on dotted line and tape onto wall. Use level to make sure
template is level and mark wall with a sharp object such as an awl.
2. Drill 3/8” holes at top and bottom of bracket guide in center of studs.
3. A - Align bolts, through bracket holes then thread on Spring Loaded Wings. (Fig. A)
B - Collapse Wings while pushing through hole in wall. (Fig. A)
C - Pull bolt out to secure Toggle Wings against inside of wall (wings spring open
on other side of wall and securely hold bolt and bracket). (Fig. B)
D - Screw bolt in until tight.
Mark for
Drill
Mark for
Drill
Mark for
Drill
Mark for
Drill
10 inches2345678910111213141516
Bracket
Bolt
Toggle
Wall
Drilled
Hole
Wall
Spring
Loaded
Toggle
opens on
inside of
wall
Included for mounting:
4 - 1.5” Phillips head self
tapping screws
4 - toggle bolts
2 - mounting brackets
BRACKET
GUIDE
BRACKET
GUIDE
Note: The mounting hardware included is intended for mounting the heater on 3/8” to 5/8” drywall affixed to wood or metal studs. For your convenience the wall mount brackets are 16”
on center to align with 2 studs. Not all studs will be 16” on center. If you are not able to align with studs, toggle bolts are provided. For other wall types, please consult a professional or visit
your local hardware store to determine which type of hardware is best for your particular wall.
Fig. B
Fig. A
Stand Assembly:
For floor use attach the Stand to the Fireplace heater
using the 4 machine screws (provided). Gently lay the unit
on the floor and attach the Stand to the bottom. For wall
mount see Wall Mount Instructions below.
Wall Mount Installation:
This product weighs 25 lbs. Do not install alone.
Mounting Template with instructions is attached below to
make mounting your Fireplace Heater easy.
• Wall Mount Hardware Kit includes:
4 - 1.5” Phillips head self tapping screws
4 - toggle bolts
2 - mounting brackets
IMPORTANT: Before drilling into any wall ensure no
electrical cables are present in the area.
Max height of 47” (1.2m)
Make sure you allow at least 3 feet of space on sides
of unit.
1. Remove stand from main unit, if installed.
2. Secure the mounting brackets to the wall using the Wall
Mounting Template provided (see below).
3. Hang main body on wall brackets by lifting over the
Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.
Product:
Spelregels forum
Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:
lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;
Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.
Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.
Abonneren
Abonneer u voor het ontvangen van emails voor uw Bionaire BFH5000 bij:
nieuwe vragen en antwoorden
nieuwe handleidingen
U ontvangt een email met instructies om u voor één of beide opties in te schrijven.
Ontvang uw handleiding per email
Vul uw emailadres in en ontvang de handleiding van Bionaire BFH5000 in de taal/talen: Engels, Frans, Italiaans, Spaans als bijlage per email.
De handleiding is 2,26 mb groot.
U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.
Stel vragen via chat aan uw handleiding
Stel uw vraag over deze PDF
Uw handleiding is per email verstuurd. Controleer uw email
Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.
Er is een email naar u verstuurd om uw inschrijving definitief te maken.
Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken
U heeft geen emailadres opgegeven
Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.
Uw vraag is op deze pagina toegevoegd
Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.
