740637
18
Verklein
Vergroot
Pagina terug
1/23
Pagina verder
14 15
Boost function
On models with 5 output levels, the highest output level is designed as a boost function with a brief runtime and
automatic fallback function (pursuant to EEC directive). The hood runs at maximum output for about 5 minutes
and then automatically switches back to a circulation output of less than 650 m³/h.
When is touched (reduce output)
a „1“ is displayed in the output display. This means: the lowest output level „1“ is automatically selected when this
control surface is pressed.
This control surface is also used to reduce the blower output. The output level is continuously decremented down
to the lowest output level when the control surface is depressed continuously.
Dwell timer
By enabling the dwell timer, the hood remains in operation at the programmed setting for an additional X minutes
and then automatically shuts off. During this time, the hood can be reset on demand to normal mode by disabling
this function.
The control sounds cannot be disabled.
INSTALLATION INSTRUCTIONS
Before starting the installation, it is essential that you review and observe the warnings in the „Safety Instruction“
section!
Proper installation - position and height
A headless extractor hood from Bielmeier can be installed by 2 people in a minimum of time. However, we
recommend having the installation performed professionally. Bielmeier is not liable for damage caused by
installation defects.
The hood should be installed on a masonry wall, but at least on a solid wall. Wooden walls, sheetrock structures,
etc. are unsuited, since these act as resonating cavities when the blower is in operation, therefore causing elevated
operating noise.
Contact your stove manufacturer to determine whether a extractor hood can operated above the stove. In order
to determine the ideal clearance between the hood and the stove top, the distance from the horizontal center of
the hood front should be measured to the stove top while the hood is hung. The following specifications generally
apply for headless extractor hoods if the manufacturer of the cooking equipment did not provide separate safety
clearances.
Clearance to electrical stove top
A minimum clearance of 650 mm must be adhered to between an electrical stove top and the horizontal center of
the extractor hood.
Clearance to gas stove top
A minimum clearance of 750 mm must be adhered to between an gas stove top (top edge of pot support) and
the horizontal center of the extractor hood.
Clearance to induction stove top
The clearance for induction stove tops is the same as for electrical stove tops.
If different cooking equipment is used, the larger specified clearance always applies.
Width of hood in relation to stove top
The width of the extractor hood and the width of
the stove top should be identical.
Cover the stove top while installing the hood to
avoid damaging the stove top.
Install the hood in a dry location without direct exposure to sunlight. Verify that the wall has the
proper strength and load-bearing capacity. Install the hood centered over the stove top
OVERVIEW OF YOUR EXTRACTOR HOOD
Overview of supplied scope
1 – NPower plug (E.-No. 950.001)
2 – Flexible hose/ exhaust hose (E.-No. 950.002)
3 – Control panel (E.-No. 950.003)
4 – Pipe adapter (E.-No. 950.004)
5 – Capacitor (E.-No. 950.005)
6 – Cover / circuit board (E.-No. 950.006)
7 – Circuit board (E.-No. 950.007)
8 – Magnet (E.-No. 950.008)
9 – Telescoping spring (E.-No. 950.009)
10 – Switch control (E.-No. 950.010)
11 – LED spotlight (E.-No. 950.011)
12 – Aluminum filter (E.-No. 950.012)
13 – Motor blower (E.-No. 950.013)
14 – Motor enclosure (E.-No. 950.014)
15 – Motor (E.-No. 950.015)
16 – Motor cover bracket (E.-No. 950.016)
17 – Cover (E.-No. 950.017)
18 – IR remote control (E.-No. 950.018)
19 – Operator panel (E.-No. 950.019)
20 – Glass insert 1 (E.-No. 950.020)
21 – Glass insert 2 (E.-No. 950.021)
22 – Hood body (E.-No. 950.022)
23 – Base wall sleeve(E.-No. 950.023)
24 – Telescopic wall sleeve (E.-No. 950.024)
25
Installation bracket for telescopic wall sleeve (E.-No. 950.025)
26 – Screw 6 x 80 mm & 8x80mm (E.-No. 950.026)
27 – Screw 4 x 6 mm (E.-No. 950.027)
28 – Electrical drive (E.-No. 950.028)
29 – Transformer (E.-No. 950.029)
30 – LED spotlight (E.-No. 950.030)
GB
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bielmeier BHG39 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bielmeier BHG39 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 2,62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info