779501
27
Verklein
Vergroot
Pagina terug
1/87
Pagina verder
52 53
MTB-PEDELEC | ORIGINAL OPERATING INSTRUCTIONS 2016 ORIGINAL OPERATING INSTRUCTIONS 2016 | MTB-PEDELEC
b ca e fd
ENGLISH
ENGLISH
What to bear in mind with BERGAMONT bikes with carbon steerer
Always make sure before assembly to use a headset compatible with the stem.
If you want to use a product other than the original product, make sure it is
compatible with the BERGAMONT fork. BERGAMONT assumes no responsibili-
ty for problems resulting from the use of products other than series products.
Never use more than 40 mm stack height of spacers between headset and stem
(d). Never use more than 5 mm stack height of spacers above the stem between
the stem and the top cap of the headset (d). Do use minimum 5 mm stack
height of spacers below the stem between the cap of the headset and the stem.
1. The fork steerer, especially in case of a carbon steerer, must be assembled
with the originally supplied internal expander wedge. Never use a standard
star flanged nut on carbon fork steerers (e).
2. When cutting the steerer tube use handtools only. Do not use a power saw or
a speed cutter, but use a hand saw with a fine blade for metal cutting (f) and
a saw guide.
3. Once the steerer tube is cut to the desired length, be sure to remove all burrs
at the top of the steerer tube. Make sure to wear appropriate safety protec-
tion, safety goggles, gloves and breathing mask. Avoid inhaling the carbon
dust. Do not blow or sweep the dust off, but remove it with a moist rag. Dis-
pose of it immediately.
4. Apply a thin and even layer of grease on the bearings before mounting the
fork in the frame. Make sure the clamping surfaces of the stem remain clear
of grease. Otherwise there is the risk that a secure clamping of the stem is
no longer possible. Apply special carbon assembly paste on the inside of
the stem as well as on the fork steerer inside and outside in the area of the
clamping. This increases the friction and ensures a secure fit.
5. Slide the expander into the carbon steerer until it is flush with the top of the
steerer.
Check after the adjustment or assembly, whether the handlebars are firmly seat-
ed in the stem by trying to rotate the handlebars downwards (a). Verify whether
the handlebar/stem-combination can be turned relative to the fork. Do this by
taking the front wheel between your knees and trying to twist the handlebars. If
there is movement, carefully tighten the bolts a little more and check again the
proper fit (b).
Tighten carefully by approaching the prescribed maximum torque value in small
steps (0.5 Nm increments) and check in between the proper fit of the compo-
nent. Never exceed the maximum torque value indicated by BERGAMONT!
Ask your BERGAMONT dealer to explain you both function and adjustment of
your stem or, still better, let him do that work.
DANGER!
G
In the case of turned stems, it is possible that the cables are too short. In
this case riding can be unsafe. If in doubt, ask your BERGAMONT dealer.
DANGER!
G
When removing spacers (c) the fork steerer tube must be shortened.
This change is irreversible. The shortening should be carried out by your
BERGAMONT dealer, but only after you have found your preferred position.
NOTE!
i
If you want your handlebars at a higher position, you may opt for a riser
bar model which has an upward bend. If in doubt, ask your BERGAMONT
dealer.
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bergamont Pedelec 2016 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bergamont Pedelec 2016 in de taal/talen: Engels als bijlage per email.

De handleiding is 21.14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info