784247
11
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
11
Installation
6006113_a – 01.06.2022
EN
Seal the cut surface of the work top with suitable material
(heat resistant to 75 °C – e.g. special paint, silicone rubber
or cast resin).
For the material used, the worktop manufacturers
instructions must be followed.
Place the hob into the specified position in the lower
cabinet from above.
3.3.5 Establish electrical power supply
DWARNING!
Risk of death due to electric shock!
Touching live parts can cause an electric shock, burns or
death.
Ensure that the voltage supply is and remains
disconnected while the following work is in progress.
DATTENTION!
Danger of property damage due to incorrect connection!
If the hob is connected with further devices (e.g. oven),
damage can arise due to overvoltage. The customer must
provide a separate connection point with dedicated fuse for
the hob.
Make sure that the device is connected separately.
Make sure the connection is separately protected with a
circuit breaker and a residual current device.
Observe the voltage specifications on the ratings plate.
Connect the device to the power supply provided by the
customer. The junction box is located on the underside of
the device.
Connection to spring-loaded terminals (e.g. in cooker
connection boxes) is not permitted.
Connection possibilities:
y400 V ~ / 50/60 Hz – 2P+N
NL1L2
45 123
Cable H 05 VV - F, H 05 RR - F,
Diameter 4 x 2.5 mm2,
Fuse 16 A
y230 V ~ / 50/60 Hz – 1P+N
(optional, not compatible with AutoRun module)
NL1
45 123
Cable H 05 VV - F, H 05 RR - F,
Diameter 3 x 4.0 mm2,
Fuse 40 A
Route the cables so that they are not kinked, crushed or
damaged and do not come into contact with hot parts of
the device.
Make sure that the device can be disconnected on all
poles from the electricity supply after installation.
After switching on the power supply, the device is ready for
operation.
3.3.6 Check and carry out commissioning
DATTENTION!
Risk of disruptions due to moisture in the device!
If the device is moved from a cold environment into a hot
one, condensation may form inside.
Wait about 2-3 hours before bringing the device into
service.
Ensure that the device is accessible for maintenance work
at all times.
Check that an all-pole isolating device (min. 3 mm contact
gap) is present.
Check that the mains cable and the electrical connection
cable are not kinked, crushed or damaged.
Make sure that the protective film is removed.
Check the correct functioning of the device.
D“4. Operation (page 12).
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Berbel BKF 90 iPP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Berbel BKF 90 iPP in de taal/talen: Engels als bijlage per email.

De handleiding is 7.35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Berbel BKF 90 iPP

Berbel BKF 90 iPP Gebruiksaanwijzing - Nederlands - 36 pagina's

Berbel BKF 90 iPP Gebruiksaanwijzing - Deutsch - 36 pagina's

Berbel BKF 90 iPP Gebruiksaanwijzing - Français - 36 pagina's

Berbel BKF 90 iPP Gebruiksaanwijzing - Italiano - 36 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info