710690
9
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
9
EN
5 in 1 hair and beard trimmer set Use Instructions
Description of the appliance Fig.A
1. ON/OFF switch
2. Cutting length selector
3. Hair clipper head
4. Shaver head
5. Nose/ear trimmer
6. Hair and beard trimmer
7. Precision trimmer
8. Guiding combs for hair clipper head (3 – 6 – 9 – 12 mm)
9. Guiding comb for hair and beard trimmer head
10. Standing and charging base
11. Adaptor
Charging of the appliance
This appliance can be used with or without the adaptor. It is thus possible to keep using the appliance even when
the battery runs out during operation, by simply plugging it into the wall socket.
In order to do this, make sure that the appliance is turned off before plugging it into the wall socket, and wait
approx. 1 minute before turning the appliance on again.
To charge the appliance:
a. You can connect the adaptor directly to the appliance, by inserting the connection pin in the connector found
at the bottom of hair clipper;
Or
b. You can connect the adaptor to the standing and charging base, by inserting the connection pin inside the
hole found in the hair clipper housing, and blocking it with the cable stopper, to prevent it from detach or falling.
Once the connection pin is xed, simply place the hair clipper on the standing base, to start charging the ap-
pliance.
When the adaptor is plugged into the wall socket, the LED indicator on the display of the hair clipper turns red,
and stays on until the battery is charged.
When the LED indicator turns green, the appliance is fully charged and ready to use.
Complete charging of the appliance takes approximately 90 minutes, for 60 minutes of continuous operation
time.
Instructions for use
The appliance features 5 interchangeable heads, with different functions.
Hair clipper head
This head is used for cutting hair and beard. The 4 guiding combs included in the set allow to cut and trim hair
and beard at 4 different lengths: 3, 6, 9 and 12 mm.
Carefully brush hair and beard before starting to trim them.
Choose the guiding comb for the desired length, and insert it on to the hair clipper head, making sure that it it
well xed before switching on the appliance.
Note: make sure that the appliance is turned off and unplugged from the wall socket before inserting the
guiding comb on to the blade.
For best result, it is better to cut hair and beard following the direction of growth.
For a more precise trimming, you can remove the guiding comb from the hair clipper head, and cut your hair and
beard adjusting the height of the blades using the cutting length selector found on the hair clipper. This selector
allows to adjust blades to 3 different lengths: 0,8 mm – 1,1 mm – 1,4 mm.
Hair and beard trimmer
This head is used for trimming beard and hair. The guiding comb included in the set allows to choose 4 different
trimming lengths: 4, 5, 6 and 7 mm.
Do not leave the appliance unattended if close to places where it
could fall into water (shower, bath tub, sink, etc.). Should the ap-
pliance fall into water, do not try to pick it up; immediately unplug the
adaptor from the wall socket.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Beper 40742 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Beper 40742 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 1,87 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info