214619

BenQ mp 611c Handleiding

12
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
Welcome
MP611/MP611c Digital Projector
Mainstream Series
User Manual
Copyright
Copyright 2006 by BenQ Corporation. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of BenQ Corporation.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied, with respect
to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any
particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to
make changes from time to time in the contents hereof without obligation to notify any person of
such revision or changes.
*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others are
copyrights of their respective companies or organizations.
Table of contents iii
Table of contents
Important safety instructions.................................... 1
Introduction ............................................................... 5
Projector features ................................................................. 5
Shipping contents................................................................. 6
Projector exterior view ......................................................... 7
Controls and functions ........................................................ 8
Positioning your projector ...................................... 12
Choosing a location ........................................................... 12
Safety instructions for ceiling mounting of the projector 13
Obtaining a preferred projected image size ...................... 14
Connection............................................................... 17
Connecting a computer or monitor ................................. 17
Connecting Video source devices...................................... 19
Operation ................................................................. 23
Start up ............................................................................... 23
Utilizing the password function ........................................ 24
Switching input signal ........................................................ 26
Adjusting the projected image .......................................... 26
Selecting the aspect ratio ................................................... 28
Selecting a picture mode .................................................... 29
Hiding the image ................................................................ 30
Creating your own startup screen-MyScreen function ... 30
Activating panel key lock .................................................. 32
Setting the presentation timer ........................................... 33
Freezing the image ............................................................. 33
Utilizing FAQ function ...................................................... 34
Shutting down the projector ............................................. 34
Menu operation.................................................................. 35
Maintenance............................................................. 44
Care of the projector ......................................................... 44
Lamp information .............................................................. 45
Table of contentsiv
Troubleshooting....................................................... 51
Specifications............................................................ 52
Projector specifications ......................................................52
Timing chart........................................................................53
Dimensions..........................................................................54
Warranty................................................................... 55
Limited warranty ................................................................55
Regulation statements.............................................. 56
FCC statement ....................................................................56
EEC statement ....................................................................56
MIC statement ....................................................................56
WEEE directive ...................................................................56
Important safety instructions 1
Important safety instructions
Your BenQ projector is designed and tested to meet the latest standards for safety of
information technology equipment. However, to ensure safe use of this product, it is
important that you follow the instructions mentioned in this manual and marked on the
product.
Safety Instructions
1. Please read this manual before you
operate your projector. Save it for
future reference.
2. Do not look straight at the projector
lens during operation. The intense
light beam may damage your eyes.
3. Refer servicing to qualified service
personnel.
4. Always open the lens shutter or
remove the lens cap when the
projector lamp is on.
5. In some countries, the line voltage is
NOT stable. This projector is designed
to operate safely within a mains
voltage between 100 to 240 volts AC,
but could fail if power cuts or surges
of ±10 volts occur. In areas where the
mains voltage may fluctuate or cut
out, it is recommended that you
connect your projector through a
power stabilizer, surge protector or
uninterruptible power supply (UPS).
6. Do not block the projection lens with
any objects when the projector is
under operation as this could cause
the objects to become heated and
deformed or even cause a fire. To
temporarily turn off the lamp, press
BLANK on the projector or remote
control.
Important safety instructions2
Safety Instructions (Continued)
7. The lamp becomes extremely hot
during operation. Allow the
projector to cool for approximately
45 minutes prior to removing the
lamp assembly for replacement.
8. Do not operate lamps beyond the
rated lamp life. Excessive operation
of lamps beyond the rated life could
cause them to break on rare
occasions.
9. Never replace the lamp assembly or
any electronic components unless
the projector is unplugged.
10. Do not place this product on an
unstable cart, stand, or table. The
product may fall, sustaining serious
damage.
11. Do not attempt to disassemble this
projector. There are dangerous high
voltages inside which may cause
death if you should come into
contact with live parts. The only
user serviceable part is the lamp
which has its own removable cover.
Under no circumstances should you
ever undo or remove any other
covers. Refer servicing only to
suitably qualified professional
service personnel.
Important safety instructions 3
Safety Instructions (Continued)
12. Do not place this projector in any of the
following environments.
- Space that is poorly ventilated or confined.
Allow at least 50 cm clearance from walls
and free flow of air around the projector.
- Locations where temperatures may
become excessively high, such as the
inside of a car with all windows rolled up.
- Locations where excessive humidity, dust,
or cigarette smoke may contaminate
optical components, shortening the
projector's life span and darkening the
image.
- Locations near fire alarms
- Locations with an ambient temperature
above 40°C / 104°F
- Locations where the altitudes are higher
than 10000 feet.
13. Do not block the ventilation holes.
- Do not place this projector on a blanket,
bedding or any other soft surface.
- Do not cover this projector with a cloth or
any other item.
- Do not place inflammables near the
projector.
If the ventilation holes are seriously
obstructed, overheating inside the
projector may result in a fire.
14. Always place the projector on a level,
horizontal surface during operation.
- Do not use if tilted at an angle of more
than 10 degrees left to right, nor at angle
of more than 15 degrees front to back.
Using the projector when it is not fully
horizontal may cause a malfunction of, or
damage to, the lamp.
15. Do not stand the projector on end
vertically. Doing so may cause the
projector to fall over, causing injury or
resulting in damage to the projector.
10000
feet
Important safety instructions4
Safety Instructions (Continued)
16. Do not step on the projector or place
any objects upon it. Besides probable
physical damage to the projector, doing
so may result in accidents and possible
injury.
17. Do not place liquids near or on the
projector. Liquids spilled into the
projector may cause it to fail. If the
projector does become wet, disconnect
it from the power supply's wall socket
and call BenQ to have the projector
serviced.
18. This product is capable of displaying
inverted images for ceiling mount
installation.
Use only BenQ's Ceiling Mount Kit for
mounting the projector and ensure it is
securely installed.
19. When the projector is under operation,
you may sense some heated air and
odor from its ventilation grill. It is a
normal phenomenon and not a
product defect.
Introduction 5
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
• Selectable password protected function
• Compact and portable unit
• High quality manual zoom lens
• One-key auto-adjustment to display the best picture quality
• Digital keystone correction to correct distorted images
• Adjustable color balance control for data/video display
• Ultra-high brightness projection lamp
• Ability to display 16.7 million colors
• Multi-language On-Screen Display (OSD) menus
• Switchable normal and Economic modes to reduce the power consumption
• Built-in speaker provides mixed mono audio when an audio input is connected
• Powerful AV function to provide high quality video image
• Component HDTV compatibility (YP
bPr)
• The apparent brightness of the projected image will vary depending on the ambient
lighting conditions, selected input source contrast/brightness settings, and is directly
proportional to projection distance.
• The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
Introduction6
Shipping contents
The projector is shipped with the cables required for connection to a PC or video
equipment. Carefully unpack and verify that you have all of the items shown below. If any of
these items are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those
illustrated.
Optional accessories
Projector Soft carry case Quick start
guide
User manual
CD
Pull the tab before using the
remote control
User's manual Remote control with batteries
VGA cable Power cord
1. Spare lamp kit
2. Ceiling mount kit
3. Presentation Plus
4. HDTV (Y/b/Pr) cable
5. RS232 cable
Introduction 7
Projector exterior view
Front/upper side
Rear side
See "Connection" on page 17 for details.
Lower side view
1. External control panel
(See "Projector" on page 8 for
details.)
2. Vent (heated air exhaust)
3. Projection lens
4. Quick-release button
5. Lens cap
6. Focus ring and Zoom ring
7. Front IR remote sensor
7
6
2
3
4
5
1
8. Rear adjuster foot
9. Kensington anti-theft lock slot
10. AC power cord inlet
11. Rear IR remote sensor
12. USB socket
13. RS232 control port
14. RGB signal output socket
15. RGB (PC)/Component video (YPbPr/
YCbCr) signal input socket
16. Video input socket
17. S-Video input socket
18. Audio socket
12
13
14 15 16 17 18
8
9
0
19. Quick-release foot
20. Lamp cover
21. Speaker grill
22. Rear adjuster foot
2
0
2
1
19
22
Introduction8
Controls and functions
Projector
1. Power (Refer to "Start up" on page 23
and "Shutting down the projector" on
page 34 for more information.)
Turns the projector on or off.
2. Blank/Q? (Refer to "Hiding the image" on
page 30 and "Utilizing FAQ function" on
page 34 for more information.)
Used to hide the screen image. You can
press any key on the control panel to
bring the image back.
To start FAQ function, press and hold for
3 seconds.
3. Mode (Refer to "Selecting a picture mode"
on page 29 for more information.)
Sequentially selects a predefined picture
setting available for each input.
4. Source (Refer to "Switching input signal"
on page 26 for more information.)
Sequentially selects the input signal RGB,
Component Video,
S-Video or Video.
5. Auto (Refer to "Auto-adjusting the image"
on page 27 for more information.)
Automatically determines the best
picture timings for the selected input.
6. Lamp indicator light (Refer to
"Indicators" on page 49 for more
information.)
Indicates the status of the lamp. Lights up
or flashes when the lamp has developed a
problem.
7. Temperature warning light (Refer to
"Indicators" on page 49 for more
information.)
Flashes red if the projector’s temperature
becomes too high.
8. Power indicator light (Refer to
"Indicators" on page 49 for more
information.)
Lights up or flashes when the projector is
under operation.
9. 3 Left
10. Right 4(Refer to "Correcting keystone"
on page 27 for more information.)
When the on-screen menu is not
activated, #9 and #10 function as
Keystone -/+ hot keys.
11. 6Menu (Refer to "Using the menus" on
page 36 for more information.)
Turns on the on-screen display control
menu.
13
14
7
12
8
5
4
1
9
10
2
3
11
6
Introduction 9
12. 5Exit
Exits and saves the menu settings.
When the on-screen menu is activated,
the #9 to #12 buttons are used as
directional arrows to select the desired
menu items and to make adjustments.
13. Focus ring (Refer to "Fine-tuning the
image size and clarity" on page 27 for
more information.)
Adjusts the focus of the projected image.
14. Zoom ring (Refer to "Fine-tuning the
image size and clarity" on page 27 for
more information.)
Adjusts the size of the image. Rotate
clockwise to enlarge the image or rotate
counter-clockwise to reduce the image
size.
Introduction10
Remote control
1. Power (Refer to "Start up" on page 23
and "Shutting down the projector" on
page 34 for more information.)
Turns the projector on or off.
2. Freeze
Freezes the projected image. An icon
" " will display in the lower right
corner of the screen. To release the
function, press Freeze again.
3. 5Up, 6 Down
4. 3Left, Right4
When the on-screen menu is activated,
the 5Up, 6 Down, 3Left and
Right4buttons are used as directional
arrows to select the desired menu items
and to make adjustments.
5. Menu (Refer to "Using the menus" on
page 36 for more information.)
Displays or hides the On-Screen Display
(OSD) menu system.
6. Keystone (Refer to page
"Correcting keystone" on page 27 for
more information.)
Manually corrects distorted images
resulting from an angled projection.
7. Timer On/Show (Refer to "Setting the
presentation timer" on page 33 for more
information.)
A multifunctional key that activates,
displays or hides on-screen timer based
on your own timer setting.
8. Timer Setup (Refer to "Setting the
presentation timer" on page 33 for more
information.)
Enters presentation timer setting directly.
9. Auto (Refer to "Auto-adjusting the
image" on page 27 for more
information.)
Automatically determines the best
picture settings for the displayed image.
10. Source (Refer to "Switching input signal"
on page 26 for more information.)
Sequentially selects the input signal RGB,
Component Video,
S-Video or Video.
11. Blank (Refer to "Hiding the image" on
page 30 for more information.)
Used to hide the screen image. Press any
key on the remote control to restore the
image.
12. Mode (Refer to "Selecting a picture
mode" on page 29 for more information.)
Sequentially selects a predefined picture
setting available for each input.
1
2
3
4
5
3
6
7
8
9
10
11
12
Introduction 11
Remote control effective range
Infra-Red (IR) remote control sensors are located on the front and the back of the projector.
The remote control must be held at an angle within 30 degrees perpendicular to the
projector's IR remote control sensors to function correctly. The distance between the remote
control and the sensors should not exceed 6 meters (~ 20 feet).
Make sure that there are no obstacles between the remote control and the IR sensors on the
projector that might obstruct the infra-red beam.
Replacing the remote control battery
1. Pull out the battery holder.
Please follow the illustrated instructions. Push
and hold the locking arm whilst pulling out the
battery holder.
2. Insert the new battery in the holder. Note
the positive polarity should face outward.
3. Push the holder into the remote control.
• Avoid excessive heat and humidity.
• There may be battery damage if the battery
is incorrectly replaced.
• Replace only with the same or equivalent type recommended by the battery
manufacturer.
• Dispose of the used battery according to the battery manufacturer’s instructions.
• Never throw a battery into a fire. There may be danger of an explosion.
• If the battery is dead or if you will not be using the remote control for a long time, remove
the battery to prevent damage to the remote control from possible battery leakage.
• Operating the projector from the
front
A
p
p
r
o
x
.
1
5
°
• Operating the projector from the
rear
A
p
p
r
o
x
.
1
5
°
Positioning your projector12
Positioning your projector
Choosing a location
Your projector is designed to be installed in one of four possible installation locations:
1. Table in front of screen;
2. Ceiling in front of screen;
3. Table at rear of screen;
4. Ceiling at rear of screen.
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
1. Front Table
Select this location with the projector placed near the
floor in front of the screen. This is the most common
way to position the projector for quick setup and
portability.
2. Front Ceiling
Select this location with the projector suspended
upside-down from the ceiling in front of the screen.
Purchase the BenQ Projector Ceiling Mounting Kit
from your dealer to mount your projector on the
ceiling.
Set in the Advanced > Mirror menu after you
turn the projector on.
3. Rear Table
Select this location with the projector placed near the
floor behind the screen.
Note that a special rear projection screen is required.
Set in the Advanced > Mirror menu after you
turn the projector on.
4. Rear Ceiling
Select this location with the projector suspended
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the
BenQ Projector Ceiling Mounting Kit are required for
this installation location.
Set in the Advanced > Mirror menu after you
turn the projector on.
Positioning your projector 13
Safety instructions for ceiling mounting of the
projector
We want you to have a pleasant experience using your BenQ projector, so we need to bring
this safety matter to your attention to prevent damage to person and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a
proper fitting BenQ projector ceiling mount kit and that you ensure it is securely and safely
installed.
If you use a non-BenQ brand projector ceiling mount kit, there is a safety risk that the
projector may fall from the ceiling due to an improper attachment through the use of the
wrong gauge or length screws.
You can purchase a BenQ projector ceiling mount kit from the place you purchased your
BenQ projector. BenQ recommends that you also purchase a separate Kensington lock
compatible security cable and attach it securely to both the Kensington lock slot on the
projector and the base of the ceiling mount bracket. This will perform the secondary role of
restraining the projector should its attachment to the mounting bracket become loose.
Positioning your projector14
Obtaining a preferred projected image size
The distance from the projector lens to the screen, the zoom setting, and the video format
each factors in the projected image size.
The maximum (native) resolution of the projector is 1024 x 768 pixels, which is a 4 to 3
aspect ratio (expressed as 4:3). To be able to project a complete 16:9 (widescreen) aspect
ratio image, the projector can resize and scale a widescreen image to the projector's native
aspect width. This will result in a proportionally smaller height equivalent to 75% of the
projector's native aspect height.
Thus, a 16:9 aspect image will not utilize 25% of the height of a 4:3 aspect image displayed
by this projector. This will be seen as darkened (unlit) bars along the top and bottom
(vertical 12.5% height respectively) of the 4:3 projection display area whenever displaying a
scaled 16:9 aspect image in the vertical center of the 4:3 projection display area.
When determining the position of your projector, you should consider its intended use and
input signal aspect ratios. All inputs (other than composite Video being fed a 16:9 aspect
signal) will display in a 4:3 aspect ratio (and will require an additional 33% display height
than that of the scaled 16:9 aspect image projection area).
IMPORTANT: Do not select a permanent projector position based upon a 16:9 projection if you
will ever need to select an input (other than composite Video being fed a 16:9 aspect signal).
The projector should always be placed horizontally level (like flat on a table), and positioned
directly perpendicular (90° right-angle square) to the horizontal center of the screen. This
prevents image distortion caused by angled projections (or projecting onto angled surfaces).
The modern digital projector does not project directly forward (like older style reel-to-reel
film projectors did). Instead, digital projectors are designed to project at a slightly upward
angle above the horizontal plane of the projector. This is so that they can be readily placed
on a table and will project forward and upwards onto a screen positioned so that the bottom
edge of the screen is above the level of the table (and everyone in the room can see the
screen).
If the projector is mounted on a ceiling, it must be mounted upside-down so that it projects
at a slightly downward angle.
You can see from the diagram on page 16, that this type of projection causes the bottom edge
of the projected image to be vertically offset from the horizontal plane of the projector.
When ceiling mounted, this refers to the top edge of the projected image.
If the projector is positioned further away from the screen, the projected image size
increases, and the vertical offset also increases proportionately.
When determining the position of the screen and projector, you will need to account for
both the projected image size and the vertical offset dimension, which are directly
proportional to the projection distance.
BenQ has provided a table of 4:3-aspect-ratio screen sizes to assist you in determining the
ideal location for your projector. There are two dimensions to consider, the perpendicular
horizontal distance from the center of the screen (projection distance), and the vertical
offset height of the projector from the horizontal edge of the screen (offset).
4:3 aspect image in a 4:3 aspect display area
16:9 aspect image scaled to a 4:3 aspect
display area
Positioning your projector 15
How to determine the position of the projector for a given
screen size
1. Select your screen size.
2. Refer to the table and find the closest match to your screen size in the left columns
labelled '4:3 Screen Diagonal'. Using this value, look across this row to the right to find
the corresponding average distance from screen value in the column labelled 'Average'.
This is the projection distance.
3. On that same row, look across to the right column and make note of the vertical Offset
value. This will determine the final vertical offset placement of the projector in
relation to the edge of the screen.
4. The recommended position for the projector is aligned perpendicular to the
horizontal center of the screen, at the distance from the screen determined in step 2
above, and offset by the value determined in step 3 above.
For example, if you are using a 120 inch screen, the average projection distance is 4467 mm
and with a vertical offset of 183 mm.
If you place the projector in a different position (to that recommended), you will have to tilt
it down or up to center the image on the screen. In these situations, some image distortion
will occur. Use the Keystone function to correct the distortion. See "Correcting keystone" on
page 27 for details.
How to determine the recommended screen size for a
given distance
This method can be used for situations where you have purchased this projector and would
like to know what screen size will fit in your room.
The maximum screen size is limited by the physical space available in your room.
1. Measure the distance between the projector and where you want to position the
screen. This is the projection distance.
2. Refer to the table and find the closest match to your measurement in the average
distance from screen column labelled 'Average'. Check that your measured distance is
between the min and max distances listed on either side of the average distance value.
3. Using this value, look across that row to the left to find the corresponding screen
diagonal listed in that row. That is the projected image size of the projector at that
projection distance.
4. On that same row, look across to the right column and make note of the vertical Offset
value. This will determine the final placement of the screen in relation to the
horizontal plane of the projector.
For example, if your measured projection distance was 4.5m (4500mm), the closest match in
the Average column is 4593 mm. Looking across this row shows that a 3000 mm (3 m)
screen is required. If you can only obtain imperial sized screens, the listed screen sizes on
either side of the 3 m screen are the 9' and 10' screens.
Checking the min and max projection distance values for these screen sizes, indicates that
the 4.5 m measured projection distance will need to be reduced to fit the 9' size screen, or
increased to fit the 10' size screen. The projector can be adjusted (using the zoom control) to
display on these different screen sizes at those projection distances. Be aware that these
different screens have different vertical offset values.
Positioning your projector16
There is 3% tolerance among these numbers due to optical component variations. BenQ
recommends that if you intend to permanently install the projector, you should physically test
the projection size and distance using the actual projector in situ before you permanently
install it, so as to make allowance for this projector's optical characteristics. This will help you
determine the exact mounting position so that it best suits your installation location.
4:3 Screen Diagonal Distance from Screen in mm Vertical Offset in mm
Feet Inches mm Min length
(with max.
zoom)
Average Max length
(with min.
zoom)
4 48 1219 1778 1867 1956 73
1500 2187 2297 2406 90
5 60 1524 2222 2333 2444 91
6 72 1829 2667 2800 2933 110
2000 2916 3062 3208 120
7 84 2134 3111 3267 3422 128
8 96 2438 3556 3733 3911 146
2500 3645 3828 4010 150
9 108 2743 4000 4200 4400 165
3000 4347 4593 4812 180
10 120 3048 4444 4667 4889 183
3500 5104 5359 5614 210
12 144 3658 5334 5601 5867 219
4000 5833 6124 6416 240
15 180 4572 6667 7000 7333 274
5000 7291 7655 8020 300
18 216 5486 7999 8399 8799 329
6000 8749 9186 9624 360
25 300 7620 11111 11667 12222 457
Maximum zoom
Minimum zoom
Projection distance
Center of lens
Screen
Offset
Connection 17
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
In the connections shown below, some cables may not be included with the
projector (see "Shipping contents" on page 6). They are commercially available
from electronics stores.
Connecting a computer or monitor
Connecting a computer
The projector provides a VGA input socket that allows you to connect it to a laptop or
desktop computer.
To connect the projector to a laptop or desktop computer:
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the
computer.
2. Connect the other end of the VGA cable to the D-SUB/COMP IN signal input socket
on the projector.
3. If you wish to make use of the projector (mixed mono) speaker, take a suitable audio
cable and connect one end of the cable to the audio output socket of the computer,
and the other end to the Audio socket of the projector.
The final connection path should be like that shown in the following diagram:
Many laptops do not turn on their external video ports when connected to a projector. Usually
a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a function
key labeled CRT/LCD or a function key with a monitor symbol on the laptop. Press FN and the
labeled function key simultaneously. Refer to your laptop’s documentation to find your
laptop’s key combination.
Laptop or desktop computer
USB cable
Audio cable
VGA cable
Connection18
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you
can connect the RGB signal output socket on the projector to an external monitor with a
VGA cable following the instructions below:
1. Connect the projector to a computer as described in "Connecting a computer" on page
17.
2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to the
D-Sub input socket of the video monitor.
3. Connect the other end of the cable to the D-SUB OUT socket on the projector.
The final connection path should be like that shown in the following diagram:
The D-Sub output only works when an appropriate D-Sub input is made to the projector.
Laptop or desktop computer
VGA cable
VGA cable
Connection 19
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the
following output sockets:
• Component Video
•S-Video
•Video (composite)
You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:
Best video quality
The best available video connection method is Component Video (not to be confused with
composite Video). Digital TV tuner and DVD players output Component Video natively, so
if available on your devices, this should be your connection method of choice in preference
to (composite) Video.
See "Connecting a Component Video source device" on page 20 for how to connect the
projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video.
If you have both composite Video and S-Video output terminals on your Video source
device, you should elect to use the S-Video option.
See "Connecting an S-Video source device" on page 21 for how to connect the projector to
an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.
See "Connecting a composite Video source device" on page 22 for how to connect the
projector to a composite Video device.
Connecting Audio
The projector has a built-in mono speaker which is designed to provide basic audio
functionality accompanying data presentations for business purposes only. It is not designed
for, nor intended for stereo audio reproduction use as might be expected in home theatre or
home cinema applications. Any stereo audio input (if provided), is mixed into a common
mono audio output through the projector speaker.
If you have a separate sound system, you will most likely want to connect the audio output
of your Video source device to that sound system, instead of to the mono audio projector.
The audio connections illustrated in the following sections are provided for informational
purposes only. You need not connect audio to the projector if there is an alternate sound
system available, or if audio is not required.
Connection20
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video
output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1. Take the (optional accessory) Component Video to VGA (D-Sub) adaptor cable and
connect the end with 3 RCA type connectors to the Component Video output sockets
of the Video source device. Match the color of the plugs to the color of the sockets;
green to green, blue to blue; and red to red.
2. Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with
a D-Sub type connector) to the D-SUB/COMP IN socket on the projector.
3. If you wish to make use of the projector (mixed mono) speaker, take a suitable audio
cable and connect one end of the cable to the audio output socket of the computer,
and the other end to the Audio socket of the projector.
The final connection path should be like that shown in the following diagram:
If you connect the projector to a High Definition TV (HDTV) tuner, the following standards
are supported:
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting Audio" on page 19 for details.
• Component Video is the only video output that delivers native 16:9 aspect ratio picture.
• If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
• 480i • 480p
• 576i • 576p
• 720p (50/ 60 Hz) • 1080i (50/ 60 Hz)
Audio cables
A/V device
Component Video to
VGA (D-Sub) adaptor
cable
Connection 21
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket
available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1. Take the (optional accessory) S-Video cable and connect one end to the S-Video
output socket of the Video source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
The final connection path should be like that shown in the following diagram:
• The projector is only capable of playing mixed mono audio, even if a stereo audio input
is connected. See "Connecting Audio" on page 19 for details.
• If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
• If you have already made a Component Video connection between the projector and this
S-Video source device using Component Video connections, you need not connect to
this device using an S-Video connection as this makes an unnecessary second
connection of poorer picture quality. See "Connecting Video source devices" on page 19
for details.
A/V device
Audio cables
S-Video cable
Connection22
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video
output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an composite Video source device:
1. Take the (optional accessory) Video cable and connect one end to the composite Video
output socket of the Video source device.
2. Connect the other end of the Video cable to the VIDEO socket on the projector.
The final connection path should be like that shown in the following diagram:
• The projector is only capable of playing mixed mono audio, even if a stereo audio input
is connected. See "Connecting Audio" on page 19 for details.
• If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
• You need only connect to this device using a composite Video connection if Component
Video and S-Video inputs are unavailable for use. See "Connecting Video source
devices" on page 19 for details.
A/V device
Audio cables
Video cable
Operation 23
Operation
Start up
1. Plug the power cord into the projector and
into a wall socket. Turn on the wall socket
switch (where fitted). Check that the Power
indicator on the projector lights orange after
power has been applied..
2. Remove the lens cap. If it is left on, it could
become deformed due to the heat produced by the
projector lamp.
3. Press and hold (for 2 seconds) Power
on the projector or remote control to start
the projector. A "Power On Tone" will be
heard. The Power indicator light flashes
green and stays green when the projector
is on.
The start up procedure takes about 30
seconds. In the later stage of start up, a
startup logo is projected.
(If necessary) Rotate the focus ring to
adjust the image clearness.
• If you don't want to activate Power on/off tone, you can enter the OSD menu to disable this
function. See "Mute (off)" on page 40 for details.
• If the projector is still hot from previous activity, it will run the cooling fan for
approximately 90 seconds before energizing the lamp.
4. If you are prompted for a password, press the arrow buttons to enter a four digit
password. See "Utilizing the password function" on page 24 for details.
5. Switch on all of the connected equipment.
The projector will start to search for input signals. The current input source being
scanned displays in the center of the screen. The searching message will continue
displaying until an input source signal is found.
Yo u c a n p re s s SOURCE on the projector or remote control to select your desired input
signal. See "Switching input signal" on page 26 for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen.
Operation24
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an
option for setting up password security. The password can be set through the On-Screen
Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the
menus" on page 36.
WARNING: You will be inconvenienced if you activate the password functionality and
subsequently forget the password. Print out this manual (if necessary) and write the password
you used in this manual, and keep the manual in a safe place for later recall.
Setting a password
Once a password has been set and activated, the projector cannot be used unless the correct
password is entered every time the projector is started.
1. Open the OSD menu and go to Setting > Password. Select On by pressing
Left 3 or Right4.
2. When the function is activated for the first time, a prompt will display on the screen.
3. As pictured to the right, the four arrow buttons
(Up 5, Right4, Down 6, Left 3) respectively
represent 4 digits (1, 2, 3, 4). Press the arrow
buttons to enter four digits for the password.
4. When all digits are entered and the password is
ready, press Auto to confirm.
IMPORTANT: The digits being input will display
as asterisks on-screen. Write your selected
password down here in this manual in advance
or right after the password is entered so that it is
available to you should you ever forget it.
Password: __ __ __ __
Keep this manual in a safe place.
5. Enter the password again for verification.
6. Perform one of the following 3 steps.
i. Press Auto to continue. The set-up is finished when the message “Password setup
completed” displays.
ii. Press Up 5 to clear and re-enter four digits.
iii. Press Down 6 to cancel the password set-up and return to the on-screen menu.
To disable password protection, go to
Setting > Password after opening the OSD
menu system. Select Off by pressing Left 3 or Right4. Then press Down 6 to confirm or
Up 5 to cancel.
Note that though the password function is disabled, you need to keep the old password in
hand should you ever need to change the password by entering the old password.
Input Password
Confirm
Cancel
Clear
Auto
Operation 25
If you forget the password
You will be asked to enter the four digit
password every time you turn on the projector.
If you enter the wrong password, the password
error message displays. You can retry by pressing
Up 5, or if you did not record the password in
this manual, and you absolutely do not
remember it, you can use the password recall
procedure.
Entering the password recall procedure
Press and hold Right4on the projector for 3 seconds. The projector will display 4 sets of
coded number on the screen. Write down the number and turn off your projector. Seek help
from the local BenQ service center to decode the number. You may be required to provide
proof of purchase documentation to verify that you are an authorized user of the projector.
Changing the password
1. Open the on-screen menu and go to Setting > Change Password.
2. Press Left 3or Right4.
3. Enter the old password.
i. If the password is correct, you can go on to enter new password.
ii. If the password is incorrect, a “Password Error” message displays. Press Up 5 to
try again or press Down 6 to cancel.
4Enter a new password.
IMPORTANT: The digits being input will display as asterisks on-screen. Write your
selected password down here in this manual in advance or right after the password is
entered so that it is available to you should you ever forget it.
Password: __ __ __ __
Keep this manual in a safe place.
5. Perform one of the following 3 steps.
i. Pressing Auto to confirm.
ii. Press Up 5 to try again.
iii. Press Down 6 to cancel the set-up and return to the on-screen menu.
6 Confirm the new password by re-entering the new password.
7. Perform one of the following 3 steps.
i. Pressing Auto completes the procedure.
ii. Press Up 5 to try again.
iii. Press Down 6 to cancel the set-up and return to the on-screen menu.
Password Error
Try again
Forgot password, please refer to User's manual
Operation26
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only
display one at a time.
When SOURCE on the projecotr control panel
or the remote control is pressed, information of
current signal and resolution will display at the
lower right corner. Press SOURCE again to
display a source selection bar. You can manually
press SOURCE repeatedly until your desired
signal is selected or let the projector
automatically search for the availabel signal.
Once detected, the selected source information
will display at the lower right corner of the
screen for 3 seconds. If there is multiple
equipment connected to the projector, you can
press the button again to search for another
signal.
Be sure the Source Scan function in the Advanced menu is activated if you want the
projector to automatically search the signals. See "Source Scan (on)" on page 41 for details
The brightness level of the projected image will change accordingly when you switch between
different input signals. Data (graphic) "PC" presentations using mostly static images are
generally brighter than "Video" using mostly moving images (movies).
The input type affects the options available for the Application Mode. See "Selecting a picture
mode" on page 29 for details.
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These
adjusters change the image height and projection angle. To adjust the projector:
1. Lift the projector up and press the
adjuster button to release the
adjuster. The adjuster will drop
into position and be locked.
Do not look into the lens while the lamp is
on. The strong light from the lamp may
cause damage to your eyes.
2. Screw the rear adjuster foot to fine
tune the horizontal angle.
To retract the foot, hold up the projector
while pressing the quick-release button, then slowly lower the projector. Screw the rear
adjuster foot in a reverse direction.
If the screen and the projector are not perpendicular to each other, the projected image
becomes vertically trapezoidal. To correct this situation, adjust the value of Keystone in the
Picture menu, on the projector control panel, or on the remote control. See "Correcting
keystone" on page 27 for details.
Operation 27
Auto-adjusting the image
In some cases, you may need to optimize the
picture quality. To do this, press AUTO on the
projector or remote control. Within 3 seconds,
the built-in Intelligent Auto Adjustment
function will re-adjust the values of Frequency
and Clock to provide the best picture quality.
The current source information will be displayed
in the lower right corner of the screen for 3
seconds.
The screen will be blank while AUTO is
functioning.
Fine-tuning the image size and clarity
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the height of
the projector, you will need to manually correct
it following ONE of these steps.
1. Press Left3/Right 4 on the control panel of
the projector to display the status bar labelled
Keystone. Press Left 3 to correct keystoning at
the top of the image. Press Right4 to correct
keystoning at the bottom of the image.
2. Press / on the remote control to
display the status bar labelled Keystone, then
press to correct keystoning at the top of the
image or press to correct keystoning at the bottom of the image.
3. Press 6 Menu on the projector or Menu on the remote control. Go to
Pro-
Picture > Keystone and adjust the values by pressing Left 3/Right 4 on the projector or
Left 3/Right 4 on the remote control.
1. Adjust the projected image to the size
that you need using the zoom ring.
2. Then sharpen the image by rotating
the focus ring.
Operation28
For example,
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and
computers are in 4:3 ratio, which is the default for this projector, and digital TV and DVDs
are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input source.
You can change the projected image ratio (no matter what aspect the source is) by entering
Pro-Picture > Aspect Ratio. Select an aspect ratio to suit the format of the
video signal and your display requirements. There are three aspect ratios available:
In the pictures below, the black portions are inactive areas and the white portions are active
areas.
1. Native: Scales an image proportionally to fit the projector's native
resolution in its horizontal width. This is suitable for the incoming
image which is either in 4:3 nor 16:9 and you want to make most use
of the screen without altering the image's aspect ratio.
2. 4:3: Scales an image so that it is displayed in the center of the screen
with a 4:3 aspect ratio. This is most suitable for 4:3 images like
computer monitors, standard definition TV and 4:3 aspect DVD
movies, as it displays them without aspect alteration.
3. 16:9: Scales an image so that it is displayed in the center of the screen
with a 16:9 aspect ratio. This is most suitable for images which are
already in a 16:9 aspect, like high definition TV, as it displays them
without aspect alteration.
16:9 aspect ratio is only sourced through the Component Video input when
being fed an appropriate 16:9 aspect signal. See "Connecting a Component Video source
device" on page 20 and "Obtaining a preferred projected image size" on page 14 for details.
0
Keystone
-6
Keystone
0
Keystone
+6
Keystone
1. Press Left 3 on the projector or
2. Press on the remote control or
3. Press Left 3on the projector or 3 on the
remote control when you are in Picture -->
Keystone menu.
1. Press Right 4 on the projector or
2. Press on the remote control or
3. Press Right
4 on the projector or 4 on
the remote control when you are in Picture -
-> Keystone menu.
Operation 29
Selecting a picture mode
The projector is preset with several predefined
application modes so that you can choose one to
suit your operating environment and input
source picture type. To select a operation mode
that suits your need, press MODE repeatedly
until your desired mode is selected. The picture
modes available for different types of signals are
listed below.
PC Signal Input
1. Dynamic Mode (Default): Maximizes the
brightness of the projected image. This
mode is suitable for environments where extra-high brightness is required, such as
using the projector in well lit rooms.
2. Presentation Mode: Is designed for presentations. The brightness is emphasized in this
mode to match PC and notebook coloring.
3. sRGB Mode: Maximizes the purity of RGB colors to provide true-to-life images
regardless of brightness setting. It is most suitable for viewing photos taken with an
sRGB compatible and properly calibrated camera, and for viewing PC graphic and
drawing applications such as AutoCAD.
4. Cinema Mode: Is appropriate for playing colorful movies, video clips from digital
cameras or DVs through the PC input for best viewing in a blackened (little light)
environment.
5. Blackboard Mode: Is designed for educational use. Images are allowed to be projected
on a dark background, such as a blackboard instead of a normal screen. It is most
suitable for a well lit environment with a dark background for projection.
YPbPr/S-Video/Video Signal Input
1. Dynamic Mode: Is suitable for playing gamebox-based video games in a normal living
room lighting level environment.
2. Standard Mode (Default): Is appropriate for viewing colorful movies, video clips
from digital cameras or DVs.
3. Cinema Mode: Is suitable for enjoying dark movies or DVD movies best viewed in a
blackened (little light) home cinema or lounge room environment.
4. Blackboard Mode: Is designed for educational use. Images are allowed to be projected
on a dark background, such as a blackboard instead of a normal screen. It is most
suitable for a well lit environment with a dark background for projection.
Operation30
Hiding the image
In order to draw the audience’s full attention to the
presenter, you can use BLANK to hide the screen
image. Press any key on the control panel to restore
the image. The word “BLANK” appears at the
lower right corner of the screen while the image is
hidden. When this function is activated with
video/S-video signal connected, the audio can still
be heard.
You can set the blank time in the
Advanced > Blank Time
to let the projector
return the image automatically after a period of time when there is no action taken on the
blank screen. Note that once BLANK is pressed, the projector enters Economic mode
automatically.
Do not block the projection lens from projecting as this could cause the blocking object to
become heated and deformed or even cause a fire.
Creating your own startup screen-MyScreen
function
In addition to selecting the projector preset startup screen from among BenQ logo, Black or
Blue screen, you can make your own startup screen by downloading pictures from your
computer to the projector.
1. Connect the projector to a desktop computer via RS232 cable (optional accessory). See
"Connecting a computer" on page 17.
2. Before download starts, be sure the projector has entered Standby Mode. Follow the
instruction below to enter Standby Mode:
i. Plug AC power, and POWER, TEMP and LAMP LEDs on the projector will flash
orange and then go off at the same time.
ii. POWER LED then turns solid orange.
3. Insert the bundled CD into the CD drive of your computer. Click Install MyScreen
Wizard and follow the on-screen instructions to proceed.
• Ensure you have sufficient privileges to install software.
• MyScreen utility may not be compatible with Windows 98/ME or Windows 2000. We
recommend you to run MyScreen utility on Windows XP.
Operation 31
4. To execute MyScreen utility:
i. After MyScreen Wizard is successfullly
installed, execute MyScreen utility by
selecting this icon from
Program Files.
ii. Click Next.
iii. Click Next.
iv. Click Browse to choose your desired
image and then click Next.
v. Cick MyScreen to begin download.
Welcome to MyScreen Wizard!
This wizard will guide you to have your own splash
screen in BenQ projector.
To continue, click "
Next
"
Next
Establish a connection to your BenQ projector
Please connect your BenQ projector to a serial port on your computer
and be sure the projector is in standby mode.
Found 'BenQ projector' on COM1
Confugure Serial Port Settings...
To continue, click "
Next
"
Next
Back
Back Next
Choose an image to download to your BenQ projector
Browse...
Downloading to your BenQ projector
Ready to download the new image as your splash screen?
Click "MyScreen" to begin.
Back
MyScreen
Operation32
• Do not unplug the RS232 cable or close MyScreen Wizard window while downloading
image. Failing to do so will lead to immediate shutdown of the projector and MyScreen
utility. If this happens, unplug the power cord and plug it again to restart the download
process.
Activating panel key lock
To prevent unauthorized changes in the settings or accidental button pushes, panel key lock
can be activated to disable all panel key functions except POWER.
Go to
Setting > Panel Key Lock, and select On by pressing Left3/Right4 on the
projector or remote control. A confirmation message displays. Press Down 6 to confirm or
press Up 5 to cancel.
To release panel key lock, press and hold MENU6
on the projector for 5 seconds, or use the remote
control to enter
Setting > Panel Key
Lock
and press Left3/Right4 to select OFF. A
confirmation message displays. Press Down 6 to
confirm or press Up 5 to cancel.
• Buttons on the remote control are still in use
when panel key lock is enabled.
• If you press POWER to turn off the projector
without disabling panel key lock, the projector will still be in locked status the next time it
is turned on.
vi. Cick Close after download finishes.
• There are limitations on image formats.
*.bmp/*.jpg/*.png/*.gif files are acceptable, but
there is no guarantee that every image file can
be downloaded successfully. It depends on
the file size and the color form.
• If the image size is too large, as pictured to the
right, a warning message will show up after
download begins. Click Back to choose
another image and try again.
MyScreen Download Finished!
Please power on your projector then set "MyScreen"
as your default splash screen.
Close
Choose an image to download to your BenQ projector
Browse...
Back
Error: Image size is too large.
1. Please save it to be *.bmp file.
2. File size less than 500K.
Operation 33
Setting the presentation timer
Presentation timer can indicate the remaining presentation time on the screen to help you
achieve better time management when giving presentation. Follow these steps to utilize this
function:
1. Press Timer Setup on the remote control to enter timer setting
directly or go to
Setting > Presentation Timer.
2. Select On by pressing Left3/Right4. A confirmation
message displays. Press Down 6 to confirm or press Up 5 to
cancel.
3. Press 6Down to go to the next option and decide the timer
period by pressing Left3/Right4.
4. Press 6Down and choose if you want the timer to show up
on the screen by pressing Left3/Right4.
5. If you select
Ye s , press 6Down to go to the next option and set the timer position as
in the upper left, upper right, lower left, or lower right corner by pressing Left3/
Right4.
6. Press 6Down and select your desired counting direction by pressing Left3/Right4.
7. Press 6Down and decide if you want to activate sound reminder by pressing Left3/
Right4. If you select
Ye s , a double beep sound will be heard at the last 30 seconds of
counting down/up, and a triple beep sound will be produced when the timer is up.
Timer On/Show on the remote control is a multifunctional key. If
the presentation timer is off, pressing this button for the first time
will activate timer and the second push on the button will display
timer on the screen. If the timer is already on, pressing this button
will display the timer on the screen.
• The duration of the on-screen timer is consistent with your timer
setting. For example, if you set the timer to always display, after
pressing this button for the first time to activate the timer, it will
remain on the screen. If you set the timer to never display, the
timer will only display on the screen for 5 seconds. Then it will
disappear. Please note the timer is still counting after hidden.
• If the timer is already on, you need to reactivate the timer everytime a new timer period is
set.
Freezing the image
Press Freeze on the remote control to freeze the image. An icon
will display in the lower right corner of the screen. To release the
function, press the Freeze button on the remote control, or the
Source button on the projector control panel. Note that pressing the
Source button will also change the input source.
Even if an image is frozen on the screen, the pictures are running on
the video or other device. If the connected devices have active audio
output, you will still hear the audio even though the image is frozen.
Operation34
Utilizing FAQ function
Press and hold BLANK/Q? on the projector for 3 seconds
or go to
Advanced > FAQ. Possible solutions to
problems encountered by users regarding image quality,
installation, special feature operation and service
information are available to you. Use Menu6/EXIT5 to
select one out of these four major categories. Press Left3/
Right4 for more specific questions. Then press 3Left/
4Right for possible solutions. To exit, press EXIT5.
Shutting down the projector
1. Press Power and a prompt
message appears. Press Power
a second time to turn the
projector off.
2. The Power indicator light
flashes orange and the lamp
shuts down, the fans
continue to run for
approximately 90 seconds to
cool down the projector.
• To protect the lamp, the
projector will not respond to
any commands during the cooling process.
• To shorten the cooling time, you can also activate the Quick cooling function. See
"Quick Cooling (off)" on page 40 for details.
3. Once the cooling process finishes, a
"Power Off Ring Tone" will be heard.
Disconnect the power cord from the
wall socket.
• Do not unplug the power cord before the
projector shutdown sequence is
complete or during the 90-second
cooling down process.
• If the projector is not properly shut
down, to protect the lamp, when you
attempt to re-start the projector, the fans
will run for a few minutes to cool down. Press Power again to start the projector after the
fans stop and the Power indicator light turns orange.
Are You Sure to Power Off?
Press "Power" Again to Power Off
Operation 35
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type
selected.
*When a Video or S-Video signal is connected, the function is only available with NTSC
system selected.
Functions available when receiving different signal types...
Sub-Menu PC Video / S-Video Component Video
Picture
Picture Mode
Color Temp
Brightness
Contrast
Picture Mode
Color Temp
Brightness
Contrast
Color
Tint*
Sharpness
Pro-Picture
Keystone
Auto Resize
Aspect Ratio
H Position
V Position
Phase
H. Size
Keystone
Auto Resize
Aspect Ratio
Setting
Mute
Volume
OSD Time
Blank Time
Quick Cooling
Panel Key Lock
Password
Change Password
Reset
Advanced
Mirror
Source Scan
Language
Splash Screen
High Altitude Mode
Auto Off
Economic Mode
Presentation Timer
FAQ
Information
Source
Resolution
Picture Mode
Equivalent Lamp
Hour
Source
System
Picture Mode
Equivalent Lamp
Hour
Source
Resolution
Picture Mode
Equivalent Lamp
Hour
Operation36
Using the menus
The projector is equipped with on-screen display (OSD) menus for making various
adjustments and settings.
There are 17 different menu languages. (Refer to page "Advanced menu" on page 41 for
more details.)
The following example describes the adjustment of the keystone.
1. Press Menu6 on the projector or Menu
on the remote control to turn the on-
screen menu on.
4. Adjust keystone values by
pressing Left 3/Right 4on the
projector or Left 3/Right 4 on
the remote control.
2. Use Left3/Right 4 on the projector or
Left 3/Right 4on the remote control
to select the
Pro-Picture
menu.
3. Press Exit5 or Menu6 on the projector
or 6/5 on the remote control to select
Keystone.
5. Press Exit5 on the projector or
press Menu twice* on the
remote control to leave and save
the setting.
*
The first press leads you back to the
submenu and the second press closes
the on-screen menu.
Auto Resize
Aspect Ratio
Keystone
H Position
V Position
Phase
H Size
On
Auto Resize
Aspect Ratio
Keystone
H Position
V Position
Phase
H Size
On
Auto Resize
Aspect Ratio
Keystone
H Position
V Position
Phase
H Size
On
Operation 37
Picture menu
Some picture adjustments are available only when certain input sources are in use.
Unavailable adjustments are not shown on the screen.
FUNCTION
(default setting
/ value)
DESCRIPTION
Picture Mode
(PC:
Dynamic;
YPbPr/ S-
Video/ Video:
Standard)
Pre-defined application modes are provided so you can optimize your
projector image set-up to suit your program type.
You can use the remote control 'Mode' button to select a predefined
application mode. See "Selecting a picture mode" on page 29 for
details.
Color Temp
(depends on
the selected
Application
mode)
There are four color temperature* settings available.
1. T1: With the highest color temperature, T1 makes the image appear
the most bluish white than other settings.
2. T2: Makes images appear bluish white.
3. T3: Maintains normal colorings for white.
4. T4: Makes images appear reddish white.
*About color temperatures:
There are many different shades that are considered to be “white” for
various purposes. One of the common methods of representing white
color is known as the “color temperature”. A white color with a low color
temperature appears to be reddish white. A white color with a high color
temperature appears to have more blue in it.
Brightness
(depends on
the selected
input source)
Adjusts the brightness of the image. The higher the value, the brighter the
image. And lower the setting, darker the image. Adjust this control so the
black areas of the image appear just as black and that detail in the dark
areas is visible.
Contrast
(depends on
the selected
input source)
Adjusts the degree of difference between dark and light in the image. The
higher the value, the greater the contrast. Use this to set the peak white
level after you have previously adjusted the Brightness setting to suit your
selected input and viewing environment.
50
-30
+70
-30
50
+70
Operation38
Color
(depends on
the selected
input source)
Increases or decreases the color intensity of the image.
Tint (50)
Adjusts the color tones of the image. The higher the value, the more
reddish the image becomes. The lower the value, the more greenish the
image becomes.
When a Video or S-Video signal is connected, the function is only
available with NTSC system selected.
Sharpness
(15)
Adjusts the image to make it look sharper or softer.
Operation 39
Pro-Picture menu
Some picture adjustments are available only when certain input sources are in use.
Unavailable adjustments are not shown on the screen.
FUNCTION
(default
setting / value)
DESCRIPTION
Keystone (0)
Corrects any keystoning of the image. Refer to "Correcting keystone" on
page 27 for more information.
Auto Resize
(on)
Automatically resizes the input signal pixel resolution to the native resolution
of the projector.
On: The pixel resolution of the input signal is converted to the native
resolution of the projector (800 x 600). For input signals with lower
resolutions, gaps in the pixels are automatically interpolated into the image
before being projected. This may distort the image clarity.
Off: The image is projected as its original resolution, with no pixel conversion.
For input signals with lower resolutions, the projected image will display
smaller than if resized to full screen. You could adjust the zoom setting or move
the projector towards the screen to increase the image size if necessary. You
may also need to refocus the projector after making these adjustments.
Aspect Ratio
(Native)
There are three options to set the image's aspect ratio depending on your input
signal source.
See "Selecting the aspect ratio" on page 28 for details.
H Position
(0)
Adjusts the horizontal position
of the projected image.
V Position
(0)
Adjusts the vertical position of
the projected image.
Phase
(depends on
the selected
input
source)
This function allows you to adjust the clock phase
to reduce image distortion.
H Size (0)
Adjusts the horizontal width of the image.
-30 +30
-30
+30
Operation40
Setting menu
FUNCTION
(default setting
/ value)
DESCRIPTION
Mute (off)
Toggles projector audio and Power On/Off Tone between on and off. To
disable Power On/Off Tone, go to
Setting > Mute and press
Left3/Right 4. Then press Down 6 to choose Power On/Off Tone and
press Left3/Right 4 to select off.
Volume (5)
Adjusts audio volume level.
OSD Time
(20)
Sets the length of time the OSD will remain active after your last button
press. The range is from 5 to 100 seconds.
Blank Time
(20)
Sets the image blank time when the Blank feature is activated, once
elapsed the image will return to the screen.
Quick
Cooling (off)
Enables or disables the Quick Cooling function. Selecting On enables the
function and projector cooling time will be shortened from a normal 90-
second duration to approximately 30 seconds.
Panel Key
Lock (off)
Disables or enables all panel key functions except POWER on the
projector and buttons on the remote control.
Password
(off)
This is a selectable function. Selecting On limits use of the projector to
only those who know the correct password. When the function is activated
for the first time, you have to set a password for it. For more information,
refer to "Utilizing the password function" on page 24. Once the password
is set and this function is selected, the projector is password-protected.
Users who do not know the correct password can not use the projector.
WARNING: You will be inconvenienced if you activate the password
functionality and subsequently forget the password.
Print out this manual (if necessary) and write the password you used
in this manual, and keep the manual in a safe place for later recall.
The password can be entered by using either the buttons on the projector
or the remote control.
The digits being input will display as asterisks on-screen.
Change
Password
You will be asked to enter the current password before changing to a new
one. For more information, refer to "Utilizing the password function" on
page 24.
Reset (No)
Returns all settings to the factory preset values.
The following settings will still remain: Mirror, Language, Password,
High Altitude Mode, Phase and H Position.
Operation 41
Advanced menu
FUNCTION
(default setting
/ value)
DESCRIPTION
Mirror (Floor
front)
The projector can be installed on a ceiling or behind a screen, or with one
or more mirrors. Contact your dealer for the ceiling mount bracket
(optional accessory) if you need to install the projector on your ceiling.
Refer to "Choosing a location" on page 12 for more information.
Source Scan
(on)
Sets whether the projector searches automatically for input signals. If the
source scan is On, the projector will scan for input signals until it acquires
a signal. If the function is not activated, the projector selects the last used
input signal. The default value is 'RGB'.
Language
(English)
Language sets the language for the OSD control menus.
Use Left 3/Right 4on the projector or remote control to select your
desired language.
Splash
Screen
(BenQ logo)
Allows you to select which logo screen will display during projector start-
up. Four modes are available: BenQ logo, Black screen, Blue screen or
MyScreen.
Operation42
High Altitude
Mode (off)
A mode for operation in areas like high altitude or high temperature. We
recommend you use the High Altitude Mode when your environment is
higher than 3000 feet above sea level, or is hotter than 40
°C, or whenever
the projector will be used for extended periods of time (>10 hours)
without shutdown.
To activate the High Altitude Mode, select On by pressing Left 3/Right
4on the projector or remote control. A confirmation message displays.
Press6.
Next time you turn on the projector, it will show a message pictured below
as a reminder during the start-up.
Operation under "High Altitude Mode" may cause a higher decibel
operating noise level because of increased fan speed necessary to improve
overall system cooling and performance.
If you use this projector under other extreme conditions excluding the
above, it may display auto shut-down symptoms, which is designed to
protect your projector from over-heating. In cases like this, you should
switch to High Altitude mode to solve these symptoms. However, this is
not to state that this projector can operate under any and all harsh or
extreme conditions.
Auto Off (Off)
This function allows the projector to turn off automatically if no input
signal is detected after a set period of time. Press Left 3/Right 4on the
projector or remote control to set the duration before the projector is
turned off.
Economic
Mode (off)
Use this mode to reduce system noise and reduce power consumption by
20%. If this mode is activated, the light output will be reduced and result
in darker projected images.
Setting the projector in Economic mode extends the lamp timer
automatic shutdown feature. For more information on how the total
lamp hour is calculated, see "Calculation of lamp hour" on page 45.
Presentation
Timer
Helps to remind the presenter to finish the presentation within a certain
timeframe. Refer to "Setting the presentation timer" on page 33 for more
information.
FAQ
Displays possible solutions to problems you may encounter.
We recommend you use the High Altitude Mode by selecting
On
whenever your environment is higher than 1500m.
Confirm to turn Altitude Mode on?
Yes
6 No 5
Current Status
High Altitude Mode On
This mode is used for protecting projector from extreme environment and may cause high
fan speed.
Operation 43
Information menu
This menu shows you the current operating status of the projector.
Some picture adjustments are available only when certain input sources are in use.
Unavailable adjustments are not shown on the screen.
FUNCTION DESCRIPTION
Source
Shows the current signal source.
Resolution
Shows the native resolution of the input signal.
Picture Mode
Shows the selected mode in the Picture menu.
Equivalent
Lamp Hour
Usage
Displays the equivalent lamp hour calculated by the built-in timer.
System
Shows the Video input system format, NTSC, SECAM or PAL.
Maintenance44
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is
to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts
need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
• Use a canister of compressed air to remove dust.
• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner
and gently wipe the lens surface.
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as
described in "Shutting down the projector" on page 34 and unplug the power cord.
• To remove dirt or dust, wipe the case with a soft, lint-free cloth.
• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
• Make sure the temperature and humidity of the storage area are within the
recommended range for the projector. Please refer to "Specifications" on page 52 or
consult your dealer about the range.
• Retract the adjuster feet.
• Remove the batteries from the remote control.
• Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent. When
you carry the projector yourself, please use the original box or provided soft carry case.
Maintenance 45
Lamp information
Calculation of lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically
calculated by the built-in timer. The method of calculating the equivalent lamp hour is as
follows:
Total (equivalent) lamp hour
= (hours used in Economic mode) + 4/3 (hours used in normal mode)
See "Economic Mode (off)" on page 42 for more information on Economic mode.
The lamp hour in Economic mode is calculated as 2/3 of that in normal mode. That is, using
the projector in Economic mode helps to extend the lamp life by 1/3.
Warning message
When the Lamp indicator lights up red or a message appears suggesting it is time to replace
the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
For more detailed information on projector warnings, please refer to "Indicators" on page
49.
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too
hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator
still lights up after turning the power back on, please contact your dealer.
The following Lamp warning displays will remind you to change the lamp.
Message Status
Total (equivalent) lamp hour has reached 3000 hours.
Install a new lamp for optimal performance.
Total (equivalent) lamp hour has reached 3950 hour.
A new lamp should be fitted to avoid the
inconvenience when the projector runs out of lamp
time.
NOTICE: Order replacement lamp
Lamp > 3000 Hours
Projector will stop at 4000 hours
Lamp > 3950 Hours
NOTICE: Replace lamp soon
Projector will stop at 4000 hours
Maintenance46
Replacing the lamp
• To reduce the risk of electrical shock, always turn the projector off and disconnect the
power cord before changing the lamp.
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes
before replacing the lamp.
• To reduce the risk of injuries to fingers and damage to internal components, use caution
when removing lamp glass that has shattered into sharp pieces.
• To reduce the risk of injuries to fingers and/or compromising image quality by touching
the lens, do not touch the empty lamp compartment when the lamp is removed.
• This lamp contains mercury. Consult your local hazardous waste regulations to dispose
of this lamp in a proper manner.
1. Turn the power off and disconnect the projector from the wall socket. If the lamp is
hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.
Total (equivalent) lamp hour has reached 4000 hours.
This message will flash in the center of the screen for
about 30 seconds together with the Lamp indicator
lighting up red for 40 seconds.
It is strongly recommended that you replace the lamp
at this age. The lamp is a consumable item. With the
usage time increase, the lamp brightness diminished
gradually. This is normal lamp behaviour. You can
replace the lamp whenever you notice that the
brightness level has significantly diminished. If the
lamp is not replaced beforehand, it must be replaced
after 4000 hours usage.
If this warning message displays, the projector will
shut down in 40 seconds. The lamp MUST be
replaced before the projector will operate normally.
Lamp > 4000 Hours
NOTICE: Replace lamp now
Lamp-usage time exceeded
Then reset lamp timer
Replace lamp (refer to User Manual)
Lamp-usage time exceeded
2. Turn the projector over. Then loosen the
screws on the lamp cover.
Maintenance 47
3. Remove the lamp cover from the projector.
Do not turn the power on with the lamp cover
removed.
4. Remove the lamp cords from the slots.
5. Disconnect the lamp connector by pushing it
against the projector while pulling it up.
6. Loosen the screw that secures the lamp.
7. Lift the handle so that it stands up. Use the
handle to slowly pull the lamp out of the
projector.
• Pulling it too quickly may cause the lamp to
break and scatter broken glass in the projector.
• Do not place the lamp in locations where water
might splash on it, children can reach it, or
near flammable materials.
• Do not insert your hands into the projector
after the lamp is removed. If you touch the
optical components inside, it could cause color
unevenness and distortion of the projected
images.
8. As shown in the figure, lower the new lamp
first and align the two holes on the lamp with
the locators on the projector.
Maintenance48
14. Restart the projector.
Do not turn the power on with the lamp cover removed.
15. Resetting the lamp counter
Do not reset if the lamp is not replaced as this could cause
damage.
i. Press and hold the Exit 5 button on the
projector for 5 seconds to display the total used
lamp time.
ii. Press Auto on the projector or on the remote
control to reset the lamp hour to “0”.
iii. Wait about 5 seconds to let the OSD disappear.
Temperature information
When the Temperature warning light is on, it is warning you of the following possible
problems:
1. The internal temperature is too high.
2. The fans are not working.
Turn the projector off and contact qualified service personnel for further help. For more
detailed information, please refer to "Indicators" on page 49.
9. Tighten the screw that secures the lamp.
• Loose screw may cause a bad connection,
which could result in malfunction.
• Do not over tighten the screw.
10. Connect the lamp connector to the projector.
11. Place the lamp cords back to the slots.
12. Replace the lamp cover on the projector.
13. Tighten the screw that secures the lamp cover.
• Loose screw may cause a bad connection,
which could result in malfunction.
• Do not over tighten the screw.
Lamp usage timer reset
0 Hours
Press "Auto" To Reset
Maintenance 49
Indicators
Illustration
• Blank -: Light OFF
•
O: Orange light
•: Light flashing
• R: Red light
•: Light ON
• G: Green light
Light Status & Description
Power Temp Lamp
Power events
The projector has just been connected to a power outlet.
--
Stand-by mode.
--
Powering up.
--
Normal operation.
--
1. The projector needs 90 seconds to cool down as it was
abnormally shut down without the normal cooling down
process. Or
2. The projector needs to cool for 90 seconds after the
power is turned off.
--
The projector has shutdown automatically. If you try to re-start
the projector, it will shutdown again. Please contact your dealer
for assistance.
Lamp events
-
The projector has shutdown automatically. If you try to re-start
the projector, it will shutdown again. Please contact your dealer
for assistance.
--
1. The projector needs 90 seconds to cool down. Or
2. Please contact your dealer for assistance.
O O O
O
G
G
O
O
O
R
R
Maintenance50
Light Status & Description
Power Temp Lamp
Thermal events
--
The projector has shutdown automatically. If you try to re-start
the projector, it will shutdown again. Please contact your dealer
for assistance.
-
-
-
-
R
R
R
R
G
R O
R
R
R
R
R
G
R
R O
G
R
R
G
R
G
G
R O
O
R
R
O
R
G
O
R O
G
R
G
G
Troubleshooting 51
Troubleshooting
THE PROJECTOR DOES NOT TURN ON.
NO PICTURE
BLURRED IMAGE
REMOTE CONTROL DOES NOT WORK
THE PASSWORD IS INCORRECT
Cause Remedy
There is no power from the power
cable.
Plug the power cord into the AC inlet on the
projector, and plug the power cord into the
power outlet. If the power outlet has a switch,
make sure that it is switched on.
Attempting to turn the projector on
again during the cooling process.
Wait until the cooling down process has
completed.
Cause Remedy
The video source is not turned on or
connected correctly.
Turn the video source on and check that the
signal cable is connected correctly.
The projector is not correctly
connected to the input source device.
Check the connection.
The input signal has not been
correctly selected.
Select the correct input signal with the Source
key on the projector or remote control.
The lens cap is still attached to the
lens.
Remove the lens cap.
Cause Remedy
The projection lens is not correctly
focused.
Adjust the focus of the lens using the focus
ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as
well as the height of the unit if necessary.
The lens cap is still attached to the
lens.
Remove the lens cap.
Cause Remedy
The battery is out of power. Replace the battery with a new one.
There is an obstacle between the
remote control and the projector.
Remove the obstacle.
You are too far away from the
projector.
Stand within 6 meters (19.5 feet) of the
projector.
Cause Remedy
You do not remember the password.
Please see "Entering the password recall
procedure" on page 25 for details.
Specifications52
Specifications
Projector specifications
All specifications are subject to change without notice.
General
Product name Digital Projector
Model name MP611/MP611c
Optical
Resolution 800 x 600 SVGA
Display system 1-CHIP DMD
Lens F/Number F=2.6 to 2.77, f= 20.4 to 23.5 mm
Lamp 200W lamp
Electrical
Power supply AC100–240V, 4.0A, 50/60 Hz (Automatic)
Power consumption 285W (Max)
Mechanical
Dimensions 278 mm (W) x 94 mm (H) x 219.5 mm (D)
Weight 5.9 lbs (2.67 Kg)
Input terminal
Computer input
RGB input D-sub 15-pin (female) x 1
Video signal input
S-VIDEO Mini DIN 4-pin port x 1
VIDEO RCA jack x1
HDTV signal input D-sub <--> Component RCA jack x3, through RGB input
Audio signal input
Audio in Mini jack stereo port
Output
RGB output D-sub 15-pin (female) x 1
USB mouse connector A/B series x 1
Speaker (mixed mono) 2 watt x 1
Environmental Requirements
Operating temperature 0°C ~ 40°C at sea level
Operating relative humidity 10% ~ 90% (without condensation)
Operating altitude • 0–1499 m at 0°C–35°C
• 1500–3000 m at 0°C–30°C
Specifications 53
Timing chart
Supported timing for PC input
Supported timing for Component-YP
bPr input
Supported timing for Video and S-Video inputs
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel
Frequency
(MHz)
Mode
640 x 480
31.469 59.940 25.175 VGA_60
37.861 72.809 31.500 VGA_72
37.500 75.000 31.500 VGA_75
43.269 85.008 36.000 VGA_85
720 x 400 31.469 70.087 28.3221 720 x 400_70
800 x 600
37.879 60.317 40.000 SVGA_60
48.077 72.188 50.000 SVGA_72
46.875 75.000 49.500 SVGA_75
53.674 85.061 56.250 SVGA_85
1024 x 768
48.363 60.004 65.000 XGA_60
56.476 70.069 75.000 XGA_70
60.023 75.029 78.750 XGA_75
68.667 84.997 94.500 XGA_85
1280 x 768 47.77 60.09 80.768 SXGA_60
1280 x 800 49.65 59.96 83.458 SXGA_60
1280 x 1024 63.981 60.020 108.000 SXGA_60
Signal Format
Horizontal
Frequency (kHz)
Vertical Frequency
(Hz)
480i(525i)@60Hz 15.73 59.94
480p(525p)@60Hz 31.47 59.94
576i(625i)@50Hz 15.63 50.00
576p(625p)@50Hz 31.25 50.00
720p(750p)@60Hz 45.00 60.00
720p(750p)@50Hz 37.50 50.00
1080i(1125i)@60Hz 33.75 60.00
1080i(1125i)@50Hz 28.13 50.00
Video mode
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Color sub-
carrier
Frequency
(MHz)
NTSC 15.73 60 3.58
PAL 15.63 50 4.43
SECAM 15.63 50 4.25 or 4.41
PAL-M 15.73 60 3.58
PAL-N 15.63 50 3.58
PAL-60 15.73 60 4.43
NTSC4.43 15.73 60 4.43
Specifications54
Dimensions
278 mm (W) x 94 mm (H) x 219.5 mm (D)
Unit: mm
219.5
278
94
64.3
53
Warranty 55
Warranty
Limited warranty
BenQ warrants this product against any defects in material and workmanship, under normal
usage and storage.
Proof of purchase date will be required with any warranty claim. In the event this product is
found to be defective within the warranty period, BenQ's only obligation and your exclusive
remedy shall be replacement of any defective parts (labor included). To obtain warranty
service, immediately notify the dealer from which you purchased the product of any defects.
Important: The above warranty shall be void if the customer fails to operate the product in
accordance with BenQ's written instructions, especially the ambient humidity must be in-
between 10% and 90%, temperature in-between 0°C and 40°C, altitude lower than 10000
feet, and avoiding to operate the projector in a dusty environment. This warranty gives you
specific legal rights, and you may have other rights which vary from country to country.
For other information, please visit support.BenQ.com
.
Regulation statements56
Regulation statements
FCC statement
CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the distance between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
EEC statement
This machine was tested against the 89/336/EEC (European Economic Community) for
EMC (Electronic Magnetic Compatibility) and fulfills these requirements.
MIC statement
B class equipment (Household purpose info/telecommunications equipment)
This equipment has undergone EMC registration for household purpose, and can be used in
any area including residential area.
WEEE directive
Disposal of Waste Electrical and Electronic Equipment by users in private households
in the European Union.
This symbol on the product or on the packaging indicates that this can
not be disposed of as household waste. You must dispose of your waste
equipment by handling it over to the applicable take-back scheme for the
recycling of electrical and electronic equipment. For more information
about recycling of this equipment, please contact your city office, the shop
where you purchased the equipment or your household waste disposal
service. The recycling of materials will help to conserve natural resources
and ensure that it is recycled in a manner that protects human health and
environment.
… 12 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw BenQ mp 611c bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van BenQ mp 611c in de taal/talen: Engels als bijlage per email.

De handleiding is 2,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van BenQ mp 611c

BenQ mp 611c Gebruiksaanwijzing - Nederlands - 61 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info