812939
34
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
INSTALLATION INSTRUCTIONS &
MANUAL FOR MAINTENANCE
VIEW BELL
XXL 3 CF/LF
Gas • res with closed combustion system
This document is an essential part of your gas • re.
Read it carefully before installation and maintenance of the
gas • re and keep it in a safe place!
Bell• res wishes you many cosy evenings with your new Bell• res gas • re
Serial number:
Production date:
3
English
Installation instructions
BELLFIRES GAS FIRE WITH CLOSED COMBUSTION SYSTEM:
View Bell XXL 3 CF (Centre Fire) (VWBXXL3 CF)
View Bell XXL 3 LF (Line Fire) (VWBXXL3 LF)
4
English
Installation instructions
IMPORTANT
These Installation Instructions form part of the documentation pack supplied
with the appliance.
The complete documentation, necessary for the installation of the appliance,
consists of:
1. INSTALLATION INSTRUCTIONS & MANUAL FOR MAINTENANCE
2. AVAILABLE COMPONENTS CONCENTRIC FLUE-SYSTEMS FOR
BELLFIRES GAS FIRES WITH CLOSED COMBUSTION SYSTEM
3. INSTRUCTIONS FOR USE & MANUAL DAILY MAINTENANCE
17
English
Installation instructions
Figure 6: Vertical chimney outlet using an existing lined chimney
(Flexible Ø100 mm and/or rigid Ø100 mm / Ø150 mm)
ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION
100
1
4
28
32
18
23
25
26
29
7
5
29
30
10, 11, 12, 13
Y
Item descriptions:
see 1.6.2
Appliance: Concentric ! ue connection Ø130-Ø200 mm
FLEXIBLE CONCENTRIC FLUE Ø100 mm - Ø150 mm SYSTEM CONNECTION
POSSIBILITIES
Assemble restriction plate:
Appliance: Distance Y Concentric connection
(min.-max.) on appliance is Ø130-Ø200 mm
2.0 - 4.0 m Width: B = 50 mm
View Bell XXL 3
4.0 - 12.0 m Width: B = 65 mm
18
English
Installation instructions
Figure 7: Vertical chimney outlet using a lined chimney with a bend > 45°
(Flexible Ø100 mm and/or rigid Ø100 mm / Ø150 mm)
(*) : (Y1 + Y2+ Y3) : X > 2 : 1
(Vertical to horizontal ratio (or 45° upwards) is always at least 2 to 1)
ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION
Y2
Y1
10, 11, 12, 13
> 45°
X
Y3
32
18
30
29
5
7
29
26
25
23 28
4
1
100
Item descriptions:
see 1.6.2
Assemble restriction plate:
Appliance: Distance Y1 (*) Distance X (*) Distance Y1 + Y2 + Y3 (*) Concentric connection
(min.-max.) (min.-max.) (min.-max.) on appliance is Ø130-Ø200 mm
View Bell XXL 3 1.0 - 11.0 m 0 - 3.0 m 1.0 - 11.0 m Width: B = 40 mm
19
English
Installation instructions
Figure 8: Vertical chimney outlet using an existing unsound lined
chimney or when no chimney liners are present
(Flexible Ø100 mm / Ø150 mm)
ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION
Y
7
6
8
1832
31
29
30
29
26
29
27
28
29
4
1
100
Item descriptions:
see 1.6.2
Assemble restriction plate:
Appliance: Distance Y Concentric connection
(min.-max.) on appliance is Ø130-Ø200 mm
2.0 - 4.0 m Width: B = 50 mm
View Bell XXL 3
4.0 - 12.0 m Width: B = 65 mm
23
English
Installation instructions
ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION
Figure 12: Horizontal wall termination
Appliance: Concentric ! ue connection
Ø130-Ø200 mm
Assemble restriction plate:
Appliance: Distance Y Distance X Concentric connection on
(min.-max.) (min.-max.) appliance is Ø130-Ø200 mm
0.5 - 1.0 m
0 - 1.6 m -
View Bell XXL 3
1.0 - 3.0 m 1.6 - 4.6 m -
Item descriptions:
see 1.6.2
100
4
128
1
Y
X19
114
110, 111, 113
0.25 m
123
Wall
Termination
Position
RIGID CONCENTRIC FLUE Ø130 mm - Ø200 mm SYSTEM CONNECTION
POSSIBILITIES and with wall outlet Ø100 mm - Ø150 mm
24
English
Installation instructions
ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION
Figure 13: Horizontal wall termination
Appliance: Concentric ! ue connection
Ø130-Ø200 mm
Assemble restriction plate:
Appliance: Distance Y1 Distance X1 Distance Y2 Distance X2 Concentric connection on
(min.-max.) (min.-max.) (min.-max.) (min.-max.) appliance is Ø130-Ø200 mm
0 - 0.5 m 0 - 0.5 m 0.5 - 1.0 m 0 - 0.6 m -
View Bell 0.5 - 1.0 m 0 - 0.5 m 0 - 0.5 m 0 - 0.6 m -
XXL 3
1.0 - 3.0 m 0 - 1.0 m 0.5 - 2.0 m 0 - 0.6 m -
1.0 - 3.0 m 0 - 3.0 m 1.0 - 3.0 m 0 - 0.6 m -
Item descriptions:
see 1.6.2
110, 111, 113
128
4
1
114
14
114
110, 113
110, 111,
113
100
19
0.16 m
Y2
X2
Y1
X1
Wall
Termination
Position
RIGID CONCENTRIC FLUE Ø130 mm - Ø200 mm SYSTEM CONNECTION
POSSIBILITIES and with wall outlet Ø100 mm - Ø150 mm
25
English
Installation instructions
ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION
Figure 14: Horizontal wall termination
Item descriptions:
see 1.6.2
4
128
1
Y
X119
114
110, 111, 113
0.25 m
123
Wall
Termination
Position
Appliance: Concentric ! ue connection
Ø130-Ø200 mm
RIGID CONCENTRIC FLUE Ø130 mm - Ø200 mm SYSTEM CONNECTION
POSSIBILITIES and with wall outlet Ø130 mm - Ø200 mm
Assemble restriction plate:
Appliance: Distance Y Distance X Concentric connection on
(min.-max.) (min.-max.) appliance is Ø130-Ø200 mm
0.5 - 1.0 m 0 - 2.6 m -
View Bell XXL 3
1.0 - 3.0 m 0 - 7.6 m -
26
English
Installation instructions
1.6.2 Item descriptions for fi gures 4 t/m 14
FIG. NO. DESCRIPTION
1 Gas fi re; Concentric ue connection Ø130/Ø200 mm
2 -
3 -
4 Restriction plate
(The different sizes restriction plates are supplied with every appliance)
5 Chimney, min. Ø150 mm internal, totally gas tight.
6 Chimney or fi reproof sleeving. Min. Ø160 mm internal.
7 Ø100 mm internal fl exible stainless steel gas vent chimney liner AISI 316TI (Gastec QA).
8 Ø150 mm internal fl exible stainless steel gas vent chimney liner AISI 316TI.
9 -
The room-sealed gas appliances have been approved in
combination with the components of the concentric fl ue systems
listed in the instruction book: ‘AVAILABLE COMPONENTS
CONCENTRIC FLUE-SYSTEMS FOR BELLFIRES GAS FIRES
WITH CLOSED COMBUSTION SYSTEM’, according to the
European CE norm for gas appliances and may therefore be used
only with these components.
The components of the concentric fl ue system of:
* Bellfi res - Muelink & Grol System
* Poujoulat - DUOGAS System
* Ontop - Metaloterm US System
* Jeremias/STB - H-Twin System (STB = Schoorsteen Techniek
Brummen NL)
* Jeremias - TWIN-GAS System
may not be used together in one installation.
Check whether the wall or roof termination kit to be used exactly
matches one of those listed i
n the above menti
oned instruction book.
For the suitable and available components for concentric
chimney systems, please consult the instruction book:
“AVAILABLE COMPONENTS CONCENTRIC FLUE-SYSTEMS
FOR BELLFIRES GAS FIRES WITH CLOSED COMBUSTION
SYSTEM”
27
English
Installation instructions
Min.1 cm
Figure 15: A clearence of at least 1 cm must be maintained between
the bottom of the appliance and the ! oor.
1.6.3 Gas connection
Operation (gas regulator block (and receiver)) outside the appliance (in the operating
unit):
The gas connection is situated where the operating unit is built in near to the appliance.
Use only gas piping with a minimum diameter of 1/2” and a shut-off valve.
1.6.4 Operating unit
If the appliance is fi tted with an operating unit comprising gas control block and receiver,
this will be located, once it has been built in, at a maximum of 50 cm from the left or
right hand side of the appliance.
1.6.5 Convection package connections
When fi tting a convection package (= convection casing and convection set (1x or 2x)),
consideration should be given to the openings at approximately 1 meter above the
appliance for the warm air exiting grids.
1.7 POSITIONING THE APPLIANCE
Important: The " replace is constructed on a suf" ciently solid ! oor that
can bear the weight of the appliance.
Ensure a free space of at least 1 cm between the bottom of
the appliance and the ! oor.
Ensure that the temperature of the ! oor under and in front of
the appliance can never rise above 85°C#
Make use of a temperature protection plate (of non! ammable
material) on the ! oor if necessary.
Take care with a ! oor made of a ! ammable material.
28
English
Installation instructions
The appliance can be easily installed View Bell XXL 3 with options:
using a set of carrying brackets 10 cm frame (4 sided) and mantle iron
(accessory). After installing: convection package
remove carrying brackets!
Never position the appliance directly against the rear wall,
but always place an non! ammable insulation plate, at least
12 mm thick, between the appliance and the rear wall, with
free space on either side of 2 cm. (Total ± 5 cm.)
The rear wall must be made of non! ammable material.
Never use combustible materials during the installation.
Ventilate the " replace, by allowing vents above and
below the " replace.
During installation of the gas " re, a clearance of 3 mm
should be maintained on all sides of the appliance to
allow for expansion of the appliance during operation.
Do not insulate the appliance# Only the top and sides
may be " tted with a strip of white, loose insulation wool
(heat-resistant to 1000°C), width 15 cm max. to protect
the wall.
Do not use " breglass or Rockwool, or any other sort of
insulating material. These emit a pungent odour.
This is considered extremely unpleasant. They may also
cause discolouring of the column.
Flammable materials, such as curtains, should not
be placed in the vicinity of the gas " re.
Minimum safe distance: 100 cm.
If desired, " t a convection package to the appliance.
(See chapter 1.1)
29
English
Installation instructions
Figure 16: Appliance installed in ventilated chimney breast
Horizontal outlet of the ! ue gas exhaust /combustion air
supply via the wall.
Fitted with the options / accessories:
convection package (= convection casing and 1x convection set)
1x extra convection set
1 Inlet opening (appliance) convection air
2 Inlet opening (grate) (chimney breast) convection air
3 Natural convection in the chimney breast
4 Outlet opening (grate) (chimney breast) natural convection air
5
Outlet opening (appliance) convection air / connection convection set (2x or 4x)
6
Outlet opening (grill convection set) (chimney breast) convection air (2x or 4x)
7 -
8 Concentric fl ue connection appliance; Ø130-200 mm for a horizontal wall outlet
9 Horizontal wall outlet
10 Built in operating unit with gas regulator block and receiver
34
English
Installation instructions
Gas pipe
“rear burner”
Ø8 mm Flex.
Gas valve
“rear burner”
Gas pipe
“front burner”
Ø8 mm Flex.
Gas supply
connection
Gas regulator block
Thermocouple
Pilot light pipe
Ø4 mm Flex.
Thermocouple
interrupter
Figure 19: Gas regulator block and gas valve: Gas and thermocouple connections
Important : Cement and chalk can damage
the piping and can, in turn,
lead to gas leaks.
Disassembly and assembly of pipes and cables:
If necessary for mounting, all pipe compression fi ttings and cable connectors can be
temporarily disassembled. After mounting, carefully reassemble all pipes and cables.
Check afterwards all compression fi ttings for leaks and that all electric connections are
properly connected.
Important : Screw the thermocouple connection (and thermocouple
interrupter) manually into the gas regulator block. Afterwards,
carefully fasten a half turn with a spanner.
Note : Check that the fl exible burner pipes are correctly connected!
The gas connection of the gas valve “rear burner” must be
connected to the “rear burner”! See Chapter 5. Switching over the
exible burner pipes during assembly can lead to an explosive
ignition. Prevent this at all costs!
34

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bellfires View Bell XXL 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bellfires View Bell XXL 3 in de taal/talen: Engels als bijlage per email.

De handleiding is 3.45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Bellfires View Bell XXL 3

Bellfires View Bell XXL 3 Installatiehandleiding - Nederlands - 76 pagina's

Bellfires View Bell XXL 3 Gebruiksaanwijzing - Nederlands - 36 pagina's

Bellfires View Bell XXL 3 Installatiehandleiding - Deutsch - 92 pagina's

Bellfires View Bell XXL 3 Gebruiksaanwijzing - Deutsch - 36 pagina's

Bellfires View Bell XXL 3 Gebruiksaanwijzing - English - 36 pagina's

Bellfires View Bell XXL 3 Installatiehandleiding - Français - 76 pagina's

Bellfires View Bell XXL 3 Gebruiksaanwijzing - Français - 36 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info