Handleiding Bellfires VIEW BELL TOPSHAM 3 (pagina 7 van 36) (Engels)

645680

Verklein

Vergroot

Pagina terug

1/36

Pagina verder

This document is an essential part of your gas • re.

Read it carefully before use of the gas • re and keep it in a safe place!

INSTRUCTIONS FOR USE &

MANUAL DAILY MAINTENANCE

VIEW BELL TOPSHAM 3

CF / LF / PF

Gas • re with closed combustion system

Bell• res wishes you many cosy evenings with your new Bell• res gas • re

Serial number:

Production date:

Bellﬁ res English

Instructions for use

BELLFIRES GAS FIRE WITH CLOSED COMBUSTION SYSTEM:

View Bell Topsham 3 CF (Centre Fire) (VWBTS3 CF)

View Bell Topsham 3 LF (Line Fire) (VWBTS3 LF)

View Bell Topsham 3 PF (Premium Fire) (VWBTS3 PF)

Bellﬁ res English

Instructions for use

Bellﬁ res English

Instructions for use

CONTENTS

Page

1. WARRANTY TERMS ................................................................................. 7

2. INSTRUCTIONS FOR USE ....................................................................... 9

3. USING THE APPLIANCE FOR THE FIRST TIME ..................................... 33

4. DAILY MAINTENANCE ......................................

...........

.........

.......

......

... 34

5. ANNUAL MAINTENANCE .

..............

...................................

................

........ 35

Bellﬁ res English

Instructions for use

Bellﬁ res English

Instructions for use

1 WARRANTY TERMS

Interfocos

Warranty terms

Interfocos B.V. guarantees the quality of the supplied Bell! res hearth and the quality

of the materials used. All Bell! res hearths are developed and manufactured according

to the highest possible quality standards. If, despite all this, something should prove

amiss with the Bell! res hearth you have purchased, Interfocos B.V. offers the following

manufacturer’s warranty.

Article 1: Warranty

1.1. If Interfocos B.V. determines that the Bell! res hearth you have purchased is

defective as a result of a " aw in the construction or material, Interfocos B.V.

guarantees to repair or replace the hearth free of charge, without charging any

costs for labour or spare parts.

1.2. Repair or replacement of the Bell! res hearth will be undertaken by Interfocos B.V.

or by a Bell! res dealer as designated by Interfocos B.V.

1.3. This warranty is supplementary to the existing legal national warranty of Bell! res

dealers and Interfocos B.V. in the country of purchase and is not intended to

restrict your rights and claims based on the applicable legal provisions.

Article 2: Warranty conditions

2.1. Should you wish to claim under the warranty, please contact your Bell! res dealer.

2.2. Complaints should be reported as quickly as possible after they have manifested

themselves.

2.3. Complaints will only be accepted if they are reported to the Bell! res dealer,

together with the serial number of the Bell! res hearth which is stated on the front

of the instructions for use.

2.4. In addition, the original receipt (invoice, receipt, cash receipt) showing the date of

purchase must also be submitted.

2.5. Repairs and replacements during the warranty period do not give any entitlement

to an extension of the warranty period. After a repair or replacement of warranty

parts, the warranty period shall be deemed to have started on the date of

purchasing the Bell! res hearth.

2.6. If a certain part is eligible for the warranty and the original part is no longer

available, Interfocos B.V. shall ensure that an alternative part of at least the

same quality shall be provided.

Article 3: Warranty exclusions

3.1. The warranty on the Bell! res hearth ceases to be in effect if:

a. it is not installed according to the supplied installation instructions, and to

national and/or local regulations;

b. it has been installed, connected or repaired by a non-Bell! res dealer;

Bellﬁ res English

Instructions for use

c. it has not be used or maintained according to the instructions for use;

d. it has been changed, neglected or roughly treated;

e. it has been damaged as a result of external causes (outside the hearth

itself), for example, lightning strike, water damage or • re;

3.2. In addition, the warranty lapses if the original purchase receipt shows any

change, deletion, removal or if it is illegible.

Article 4: Warranty area

4.1. The warranty is only valid in those countries where Bell• res hearths are sold

through an of• cial dealer network.

Article 5: Warranty period

5.1. This warranty will only be granted during the warranty period.

5.2. The body of the Bell• res hearth is guaranteed for a period of 10 years against

construction and/or material faults, starting from the moment of purchase.

5.3. For other parts of the Bell• res hearth, a similar warranty applies from the moment

of purchase for a period of one year.

5.4. For user parts such as glass, glass (cord), thermocouple and the interior of the

combustion chamber, a similar guarantee is given until after the • rst burning.

Article 6: Liability

6.1. A claim granted by Interfocos B.V. under this warranty does not automatically

imply that Interfocos B.V. also accepts liability for any possible damage.

The liability of Interfocos B.V. never extends further than that stated in these

warranty conditions. Any liability of Interfocos B.V. for consequential damage is

expressly excluded.

6.2. That stated in this provision is not valid if and to the extent that is derives from

a mandatory provision.

6.3. All agreements entered into by Interfocos B.V. are, unless speci• cally stated

otherwise in writing and to the extent that they are permitted based on applicable

law, subject to the Conditions of the Dutch Metal and Engineering Association

(METAALUNIEVOORWAARDEN), as • led with the registrar of the Court of

Rotterdam on 1 January 2014.

Interfocos B.V.

Hallenstraat 17

5531 AB Bladel

The Netherlands

Tel: +31-497339200

Email: info@Bell• res.com

Carefully retain the instructions for use; they show the serial number of the hearth.

You will need this if you wish to claim under the warranty.

Bellﬁ res English

Instructions for use

2 INSTRUCTIONS FOR USE

2.1 INTRODUCTION

Congratulations on your purchase of this modern Bell! res gas ! re. This quality product

will provide you with many years of enjoyment due to the " ame effect and warmth that it

provides.

Please read the instructions for use carefully before using the appliance for the ! rst time.

Keep this booklet in a safe place.

2.2 BUILT-IN PROTECTION OF THE APPLIANCE

The appliance is fully protected by means of a thermo-electric pilot light shut off in the

event of a gas escape from the main burner.

In addition, the appliance is equipped with a safety system, whereby hatches will extract

any over-pressure that arises in a controlled way. In this, the hatches in the ceiling of

the combustion chamber, brie"y open.

A loud noise can occur. If this happens, immediately close the gas tap and contact the

! tter.

2.2.1 Safety

Do not place embers, vermiculite granules, wood logs or pebbles / ‘

! re

glass’

against the pilot light burner. Make sure that the pilot " ame can

burn at all times freely over the main burner. Only in this way is proper

ignition of the main burner ensured.

Ignoring these directions could lead to a dangerous situation.

Do not place " ammable objects within 100 cm of the appliance.

Pay special attention to furnishings and ornaments around the ! re.

When igniting the pilot light and burner, always keep a minimum

distance of 100 cm from the front of the appliance.

If the pilot " ame goes out for any reason, wait for 5 minutes before

attempting to re-light it.

It is essential that the appliance, the complete concentric " ue system and

the outlet are cleaned and inspected annually by a recognised ! tter/gas

specia

lis

t. The safe operation of the appliance w

ill

thus remain gu

arante

ed.

For this, please refer to the Installation instructions (Chapter 2:

Maintenance), that are supplied separately with each appliance.

The gas ! re must never be used with the door open or the door glass

removed.

Bellﬁ res English

Instructions for use

Never place ﬂ ammable material on the ceramic log set.

The ﬁ lling of the main burner with embers, vermiculite granules,

wood logs or pebbles / ‘

ﬁ re glass’

may not under any circumstances

be changed or added to.

Do not place easily-ﬂ ammable materials, such as nylon clothing or

ﬂ ammable liquids, in the vicinity of the gas ﬁ re.

Ensure at all times that children and other people who are not

aware of the operation of the gas appliance are only in the vicinity

of the appliance exclusively under supervision.

Use a ﬁ reguard to protect the people and children mentioned

above against possible burns.

2.3 FLAME EFFECT

The appliance is supplied with a “Centre Fire”, “Line Fire” or “Premium Fire” double

burner, as ordered, from the factory. These burners each have their own speciﬁ c ﬂ ame

effect, see below for an impression.

View Bell Topsham 3 CF

The appliance is supplied with a “Centre Fire” double burner:

Both burners ON

Bellﬁ res English

Instructions for use

Only front burner ON

View Bell Topsham 3 LF

The appliance is supplied with a “Line Fire” double burner:

Both burners ON

Only front burner ON

Bellﬁ res English

Instructions for use

Butane and Propane: The ﬂ ame effect produced by butane and

propane is less realistic than with natural gas.

The ﬂ ame effect is less as far as ﬂ ame

volume and height are concerned"

View Bell Topsham 3 PF

The appliance is supplied with a “Premium Fire” double burner:

Both burners ON

Only front burner ON

Natural gas: The above sketches provide an impression of the ﬂ ame effect.

This can differ from reality. The ﬂ ame effect is namely

dependant on the composition and supply pressure of the

natural gas present.

Bellﬁ res English

Instructions for use

2.4 OPERATION: REMOTE CONTROL

2.4.1 General

Read these instructions carefully before lighting the ! re ""

The appliance is operated by radio remote control. This comprises a hand-held

transmitter and a receiver. The receiver is part of the gas control block assembly.

The receiver and the gas control block are behind the (white) panel door (operating unit)

next to the appliance. Press the door inwards to open; this will release the catch and the

door will spring out.

Remote control “Centre Fire” (CF) Remote control “Premium

“Line Fire” (LF) Fire” (PF)

Bellﬁ res English

Instructions for use

Note: Hand-held transmitter and receiver are not interchangeable with previous models.

The pilot light is situated in the front of the burner, behind a cowl. Should the pilot light

go out, you must wait ﬁ ve (5) minutes before attempting to re-ignite the ﬁ re.

Important

Once the ! re is lit, it must burn at maximum for approx. 10 minutes to allow the chimney

to come up to temperature"

The appliance is supplied with a “Premium Fire” (PF) double burner:

Hand-held 2x 1.5V battery

transmitter Type LR03 or AAA

Receiver 6VDC Note:

via the 5 wire cable No batteries in the receiver. *)

from the Light-Module

Light-Module 230 VAC

*) During a power outage, you can temporarily install batteries in the receiver so that

the appliance continues to operate.

Electrical connections and batteries:

The appliance is supplied with a “Centre Fire” (CF) or “Line Fire” (LF) double burner:

Hand-held 2x 1.5V battery

transmitter Type LR03 or AAA

Receiver 4x 1.5V battery Option:

Type LR06 or AA 6VDC adapter (230 VAC).

Available from your ! tter.

Note: Remove batteries from receiver"

Bellﬁ res English

Instructions for use

2.4.2 Hand-held transmitter

The remote control works by radio signal. The hand-held transmitter is con! gured in the

factory with a unique signal code.

Figure 1: Hand-held transmitter CF/LF Hand-held transmitter PF

Bellﬁ res English

Instructions for use

Display hand-held transmitter CF/LF (8-Symbol display)

Display hand-held transmitter PF (10-Symbol display)

Figure 2: Display hand-held transmitter

Program

Mode

Child proof

Signal

Indicator

Battery

Status

Time

Thermostatic Mode

AUX-Function:

indicates that both “front burner”

and “rear burner” are ON

Eco Mode

Temperature

Countdown

Timer Fahrenheit or

Celsius:

°F/12 hour or

°C/24 hour

Child proof

Signal

Indicator

Battery Status

Time

Thermostatic Mode

AUX-Function:

indicates that both

“front burner” and

“rear burner” are

Eco ModeTemperature

Fan-Symbol:

has no function

for the appliance

Light-Symbol:

Light / Dimmer

operation.

Ambient lighting with

“Premium Fire” (PF)

double burner.

Count-

down

Timer

Program

Mode

Fahrenheit or Celsius:

°F/12 or °C/24 hour

Bellﬁ res English

Instructions for use

1 2

OFF

1 2

OFF

1 2

OFF

SETTING FAHRENHEIT OR CELSIUS

• To change between °C and °F, press and

buttons simultaneously.

Note:

Choosing °F results in a 12 hour clock.

Choosing °C results in a 24 hour clock.

SETTING THE TIME

• Pres and buttons simultaneously.

Day ﬂ ashes.

• Press or button to select a number to

correspond with the day of the week (e. g.

1= Monday,

2 = Tuesday, 3 = Wednesday,

4 = Thursday, 5= Friday, 6 = Saturday,

7= Sunday).

• Press and buttons simultaneously.

Hour ﬂ ashes.

• To select hour press or button.

• Press and buttons simultaneously.

Minutes ﬂ ash.

• To select minutes press and button.

• To conﬁ rm press and buttons

simultaneously or wait.

CHILD PROOF

ON:

• To activate press and buttons

simultaneously.

• displayed and the hand-held transmitter is

rendered inoperable, except for the off function.

OFF:

• To deactivate press

and

buttons

simultaneously.

• disappears.

Bellﬁ res English

Instructions for use

Figure 3: Receiver “RESET” button

IMPORTANT: SETTING UP SIGNAL CODE BEFORE USING THE APPLIANCE

FOR THE FIRST TIME

Before the appliance can be used, the receiver must ! rst learn the hand-held

transmitter’s signal code.

• Press the “RESET” button on the receiver, and keep this pressed until 2 beeps are

heard. See ! gure 3.

Release the “RESET” button after the second (somewhat longer) beep.

• Press, within 20 seconds, the button (small " ame) on the hand-held transmitter,

until 2 short beeps are heard. The signal code has now been set up on the receiver.

If, however, a single long beep is heard, this means that setting the signal code

has failed or that the wiring has been connected incorrectly.

You only need to set up the signal code once. It is not necessary when changing the

batteries of the hand-held transmitter or receiver.

Burner:

The appliance’s entire burner consists of a “front burner” and a “rear burner”.

Burner operation described below applies to:

1 Both “front burner” and “rear burner”.

(The -symbol (AUX -function) on the hand-held transmitter’s display is visible.)

2 Only “front burner”. The “rear burner” is turned off.

(The -symbol (AUX -function) on the hand-held transmitter’s display is not visible.)

Bellﬁ res English

Instructions for use

1 2

OFF

2.4.3 Operation (Remote control)

MANUAL MODE (HAND-HELD TRANSMITTER)

SWITCH ON THE APPLIANCE / IGNITING THE FIRE

• Open the gas supply valve in the gas pipe to the ! re.

Warning

When the pilot light is ignited, the motor turns

automatically to maximum " ame height.

Hand-Held Transmitter One-Button Operation

(Default Setting)

• Press button until two short beeps and a

blinking series of lines con! rms the start

sequence has begun; release button.

• Main gas " ows once pilot ignition is con! rmed.

• Hand-held transmitter automatically goes into

Manual Mode after main burner ignition.

Note

Change from one-button to two-button ignition operation by pressing

and holding button for 10 sec. immediately after installing batteries.

ON is displayed and 1 is " ashing. When change is complete 1 will

change to 2.

Bellﬁ res English

Instructions for use

1 2

OFF

Hand-Held Transmitter Two-Button Operation

• Press and button simultaneously until

two short beeps and a blinking series of lines

con! rms the start sequence has begun; release

buttons.

• Main gas " ows once pilot ignition is con! rmed.

• Hand-held transmitter automatically goes into

Manual Mode after main burner ignition.

Note

Change from two-button to one-button ignition operation by pressing

and holding button for 10 sec. immediately after installing batteries.

ON is displayed and 2 is " ashing. When change is complete 2 will

change to 1.

Important: • If the pilot ﬂ ame goes out for any reason, wait for 5 minutes

before attempting to re-light it.

• If the pilot light does not ignite after 3 ignition attempts;

close the gas tap and warn the ﬁ tter.

• Once the pilot light is burning, the main burner must ignite

within 10 seconds automatically.

If this does not happen, immediately close the gas tap and

warn the ﬁ tter.

• If the main burner ignites with a pop; immediately close the

gas tap and warn the ﬁ tter.

Bellﬁ res English

Instructions for use

Figure 4: Gas regulating block

• Possible error messages:

* 3 seconds: short beeps, audible when the motor-knob operates:

Receiver batteries need changing soon (having heard this signal, the

appliance can be ignited another ten times approximately).

* 5 seconds: unbroken beeps:

Error. For example, one of the cables may not be properly connected.

Important: If the pilot ﬂ ame goes out, then wait for

at least 5 minutes before repeating the

above procedure.

1 2

OFF

Motor-knob

Microswitch8-wire Receiver Jack

Pilot gas adjustment screw

(Factory set) (Puncture the casing

with a small screwdriver)

Adjustment screw

Maximum burner pressure

(Factory set and sealed)

• Press button and hold to set appliance to

pilot light.

STAND-BY MODE (PILOT LIGHT)

We recommend to let the pilot light

burn in the winter months, to prevent

condensation on the inside of the glass.

Bellﬁ res English

Instructions for use

Gradually decrease ﬂ ame height / Extinguishing

the ﬁ re

• After ignition, the burner automatically sets the

ﬂ ames to the maximum height.

• Press button to lower the ﬂ ames and to turn

off the burner. (Extinguishing the ﬁ re: Press

button and hold: pilot light remains burning

(standby position)!)

(Pressing brieﬂ y the button gradually lowers

the ﬂ ames to the low position.)

SETTING THE FLAME HEIGHT / EXTINGUISHING THE FIRE (STAND-BY)

Flame height directly to minimum position

• Pressing the button twice, automatically

lowers the ﬂ ames to the low position. (When this

happens, the ﬂ ames will ﬁ rst automatically go

to maximum!) This is indicated by “ ” on the

display.

Note: Backlight must be on for high ﬁ re and

low ﬁ re double-click operation!

1 2

OFF

1 2

OFF

Gradually increase ﬂ ame height

• Press button and hold to increase the ﬂ ame

level and to turn on the burner from the stand-by

position.

(Pressing brieﬂ y the button gradually

increases the ﬂ ames to the high position.)

Bellﬁ res English

Instructions for use

1 2

OFF

Flame height directly to maximum position

• Pressing the button twice automatically

increases the ﬂ ames to the high position.

This is indicated by “ ” on the display.

Note: Backlight must be on for high ﬁ re and

low ﬁ re double-click operation!

Important: • If you turn on the burner by pressing the button, it must

ignite within 10 seconds.

If this does not happen, immediately close the gas tap and

warn the ﬁ tter.

• If the burner ignites with a pop; immediately close the gas

tap and warn the ﬁ tter.

TURNING THE “REAR BURNER” ON AND OFF

After igniting the pilot light and the burner, the “front burner” is turned on (ON) and the

“rear burner” remains in the last chosen setting.

Turning on the “rear burner”

• Press button to turn the “rear burner” ON.

The -symbol (AUX -function) appears on

the hand-held transmitter’s display.

Bellﬁ res English

Instructions for use

• Press button.

• displayed.

• Light is on at preset level.

OFF

• Press button.

• disappears.

SETTING

• Press button and hold until ﬂ ashes.

• To adjust light between 20…100 % press or

button.

• To conﬁ rm setting either press button or wait.

• displayed.

LIGHT / DIMMER OPERATION

(Only for appliance with “Premium Fire” (PF) double burner)

Note:

The Light works independently of the Pilot ﬂ ame. If you want the light on but no ﬂ ame,

press button. If the main burner and pilot light are switched off, with button, the

light will switch off automatically.

Turning off the “rear burner”

• Press button to turn the “rear burner” OFF.

The -symbol (AUX -function) disappears on

the hand-held transmitter’s display.

Notes:

1 The “rear burner” always remains in the last switching position chosen.

2 Also when the receiver’s batteries are depleted the “rear burner” remains in the last

chosen setting.

Bellﬁ res English

Instructions for use

ON / SETTING

• Press button and hold until displayed, and

hour ﬂ ashes.

• To select hour press or button.

• To conﬁ rm press button. Minutes ﬂ ash.

• To select minutes press or button.

• To conﬁ rm press button or wait.

OFF

• Press button, and countdown time disappear.

Note:

At end of countdown time period, the ﬁ re turns

completely off. The Countdown Timer only works in

Manual, Thermostatic, and Eco Modes. Maximum

countdown time is 9 hours and 50 minutes.

Important: If the pilot ﬂ ame goes out for any reason,

wait for 5 minutes before attempting to

re-light it.

Hand-held transmitter

• Press button to turn off.

• If the appliance is not to be used for some time,

please close the gas supply valve in the gas pipe.

Note:

There is a 5 seconds delay before the next ignition

is possible.

TURNING OFF THE APPLIANCE COMPLETELY

COUNTDOWN TIMER

1 2

OFF

1 2

OFF

Bellﬁ res English

Instructions for use

MODES OF OPERATION

Thermostatic Mode

The room temperature is measured and compared

to the set temperature. The ﬂ ame height is then

automatically adjusted to achieve the set

temperature.

Eco Mode

Flame height modulates between high and low.

If the room temperature is lower than the set

temperature, the ﬂ ame height stays on high for a

longer period of time. If the room temperature is

higher than the set temperature, the ﬂ ame height

stays on low for a longer period of time. One cycle

lasts approx. 20 min.

Program Mode

PROGRAMS 1 and 2, each can be programmed to

go on and off at speciﬁ c times at a set temperature.

1 2

OFF

1 2

OFF

Bellﬁ res English

Instructions for use

1 2

OFF

1 2

OFF

THERMOSTATIC MODE

1. Press button.

2. displayed, preset temperature displayed brieﬂ y,

and then room temperature displayed.

OFF

1. Press button.

2. Press or button to enter Manual Mode.

3. Press button to enter Program Mode.

4. Press button to enter Eco Mode.

SETTING

1. Press button and hold until displayed,

temperature ﬂ ashes.

2. To adjust set temperature press or button.

3. To conﬁ rm press button or wait.

Important: Place the hand-held transmitter in a place that is not

inﬂ uenced by direct sunlight, draught, heat from

the appliance and other heat sources.

Bellﬁ res English

Instructions for use

1 2

OFF

1 2

OFF

PROGRAM MODE

1. Press button.

2. , 1 or 2, ON or OFF displayed.

OFF

1. Press or or button to enter Manual Mode.

2. Press button to enter Thermostatic Mode.

3. Press button to enter Eco Mode.

Note:

The set temperature for Thermostatic Mode is the temperature for the on time in

Program Mode. Changing the Thermostatic Mode set temperature also changes the on

time temperature in Program Mode.

Default settings

ON TIME (Thermostatic) TEMPERATURE: 21 °C (70 °F)

OFF TIME TEMPERATURE: “ ” (pilot light only)

TEMPERATURE SETTING

1. Press button and hold until ﬂ ashes.

ON and set temperature (setting in Thermostatic

Mode) displayed.

2. To continue press button or wait.

, OFF displayed, temperature ﬂ ashes.

3. Select off temperature by pressing the or

button.

4. To conﬁ rm press button.

Note:

The on (Thermostatic) and off set temperatures are the same for each day.

Bellﬁ res English

Instructions for use

1 2

OFF

1 2

OFF

1 2

OFF

DAY SETTING

5. ﬂ ashes. Press or button to choose

between , , 1, 2, 3, 4, 5, 6, 7.

6. To conﬁ rm press button.

OFF TIME SETTING

(PROGRAM 1)

12. ,1, OFF displayed, is displayed shortly,

and hour ﬂ ashes.

13. To select hour, press or button.

14. To conﬁ rm press button.

, 1, OFF displayed, displayed shortly,

and minutes ﬂ ash.

15. To select minutes press or button.

16. To conﬁ rm press button.

selected

ON TIME SETTING

(PROGRAM 1)

7. , 1, ON displayed, is displayed shortly,

and hour ﬂ ashes.

8. To select hour press or button.

9. To conﬁ rm press button.

, 1, ON displayed, displayed shortly,

and minutes ﬂ ash.

10. To select minutes press or button.

11. To conﬁ rm press button.

Bellﬁ res English

Instructions for use

Note:

Either continue to PROGRAM 2 and set on and off times or stop programming at this

point, and PROGRAM 2 remains deactivated.

Note:

PROGRAM 1 and 2 use the same on (Thermostatic) and off temperatures for ,

and Daily Timer (1, 2, 3, 4, 5, 6, 7).

Once a new on (Thermostatic) and / or off temperature has been set, that temperature

becomes the new default setting.

Note:

If , or Daily Timer are programmed for PROGRAM 1 and PROGRAM 2 on and

off times, these become the new default times. The batteries must be removed to clear

the PROGRAM 1 and PROGRAM 2 on and off times and temperatures.

or Daily Timer (1, 2, 3, 4, 5, 6, 7) selected

• Set on time and off time using same procedure as “ selected” (above).

• : Set on time and off time for both Saturday and Sunday.

• Daily Timer: Unique on and off times may be set for a single day of the week, for

multiple days of the week, or for every day of the week.

• Wait to ! nish setting.

• Press button to enter Eco Mode.

• The symbol appears.

OFF

• Press button.

• The symbol disappears.

ECO MODE

Bellﬁ res English

Instructions for use

Faults

• If the signals from the hand-held transmitter do not seem to be reaching the receiver,

the cause may be:

* Spent batteries: replace the batteries.

* An electronic problem: press the “RESET” button on the receiver.

• If the appliance regularly switches itself off, please contact your installer.

Replacing the batteries

• If the batteries are inserted incorrectly, the electronics or drive may be irreparably

damaged.

• Only replace the batteries when the appliance has been completely switched off.

The appliance is supplied with a “Centre Fire” (CF) or “Line Fire” (LF) double burner:

• The hand-held transmitter/receiver batteries have a service life of approx. one year.

We recommend you use alkaline batteries.

Rechargeable batteries are not permitted.

• If the receiver’s batteries are nearly empty, the system will turn the appliance off

completely. This will not occur if the receiver is connected to an AC power adaptor

(6V) (option).

• The batteries must be replaced whenever:

1 Hand-held transmitter : The battery symbol indicates this in the display.

: Battery fully charged

: Battery empty

2 Receiver: 3 seconds: short beeps, audible when the motor-knob operates.

1 Hand-held transmitter:

* Open the cover on the back of the transmitter.

* Remove the batteries from the battery compartment.

* Place two new 1.5V batteries (LR03 or AAA type) as indicated in the battery

compartment.

* Close the cover.

2 Receiver:

* Carefully pull the receiver assembly out of the compartment.

* Open the cover.

* Remove the batteries from the battery compartment.

* Place four new 1.5V batteries (LR06 or AA type) as indicated in the battery

compartment. The negative end (-) of the battery must always be at the contact

spring end of the compartment.

* Close the cover and place the receiver back in its holder.

Bellﬁ res English

Instructions for use

The appliance is supplied with a “Premium Fire” (PF) double burner:

• Receiver:

Because the appliance is equipped with a 230 VAC connection, no batteries are

present in the receiver.

• Hand-held transmitter:

The hand-held transmitter batteries have a service life of approx. one year.

We recommend you use alkaline batteries. Rechargeable batteries are not permitted.

Replacement of the batteries is necessary when the battery symbol indicates this in

the display.

: Battery fully charged : Battery empty

* Open the cover on the back of the transmitter.

* Remove the batteries from the battery compartment.

* Place two new 1.5V batteries (LR03 or AAA type) as indicated in the battery

compartment.

* Close the cover.

Bellﬁ res English

Instructions for use

3 USING THE APPLIANCE FOR THE FIRST TIME

The gas ! re is coated with a lacquer layer resistant to high temperature.

During the ! rst hours of operation, the burning in of the lacquer may result in an

unpleasant smell. This is harmless, however.

Operating the gas ! re at full capacity for a few hours, while ventilating the room, will

eliminate the smell.

After using your gas ! re for the ! rst few times, you may be aware of a light deposit on

the inside off the glass. This is caused by the paint curing.

Once your ! replace has cooled down, this deposit can be removed with glass cleaner or

ceramic hob cleaner.

Bellﬁ res English

Instructions for use

4 DAILY MAINTENANCE

• Ensure that as little dust, and as few particles of cigarette smoke, candles and oil

lamps as possible pollute the air in the room in which the appliance is used. Heating

of these particles by the convection system of the appliance could lead to

discoloration of the walls and ceiling. It is therefore very important to ensure that the

room in which the appliance is located is suf! ciently ventilated. Regularly remove

any dust deposits from behind the facade (top and bottom sides) by means of a

vacuum cleaner.

Important: • Regularly clean the glass on the inside of the appliance with

glass spray or ceramic hob cleaner. (See installation instructions

for dismantling/assembling the glass.)

Attention ! • If the glass is not cleaned on time, this can result

in becoming dull and difﬁ cult, if not impossible, to

clean.

• Careful with glass cleaner ! Make sure that no

glass cleaner liquid ﬂ ows in the sealing of the

inside of the glass pane at the bottom of the door.

Spray each time a little glass cleaner liquid on the

glass, and polish it off immediately.

Glass cleaner liquid in the sealing of the door can

cause dissolving of the black border on the inside

of the glass. It will become very spotty and can’t

be repaired.

• If the glass is broken or cracked, it must be immediately

replaced before operating the gas ﬁ re again.

Broken ceramic heat-resistant glass may not be

disposed in a glass recycling container, but must

be included in normal household waste.

• If anything is spilt on the ! re, switch it off immediately and wait for it to cool

down suf! ciently before cleaning. Never use scouring powder, aggressive

cleaners or ! re polish on the gas ! re. Use only a dry lint free cloth.

• Heat resistant lacquer in aerosols can be obtained from your

distributor. During the yearly maintenance, the lacquer can be used to repair

small areas of damage.

Bellﬁ res English

Instructions for use

5 ANNUAL MAINTENANCE

It is essential that the appliance, the complete concentric

ﬂ ue system (where possible) and the outlet are cleaned and

inspected annually by a recognised ﬁ tter/gas specialist.

The safe operation of the appliance will thus remain

guaranteed.

Please refer also to the Installation instructions that are

supplied separately with each appliance.

01 - 281015 - 341531

Your Bellﬁ res dealer

Bellfires VIEW BELL TOPSHAM 3 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Bellfires VIEW BELL TOPSHAM 3

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info