Handleiding Behringer Xenyx 1002FX (pagina 6 van 15) (Engels)

496327

Verklein

Vergroot

Pagina terug

1/15

Pagina verder

6 XENYX 1202FX/1002FX User Manual

The second value range (+10 to -40 dBu) refers to the line input and shows

its sensitivity. The settings for equipment with standard line-level signals

(-10dBVor +4 dBu) look like this: While the GAIN control is turned all the way

down, connect your equipment. Set the GAIN control to the external devices’

standard output level. If that unit has an output signal level display, it should

show 0 dB during signal peaks. For +4dBu, turn up GAIN slightly, for-10dBV a

bit more. Tweaking is done using the CLIP LED.

All mono input channels include a 3-band equalizer. All bands provide boost or

cut of up to 15 dB. In the central position, the equalizer is inactive.

The circuitry of the British EQs is based on the technology used in the best-known

top-of-the-line consoles and providing a warm sound without any unwanted

side eects. The result are extremely musical equalizers which, unlike simple

equalizers, cause no side eects such as phase shifting or bandwidth limitation,

even with extreme gain settings of ±15 dB.

The upper (HIGH) and the lower band (LOW) are shelving lters that increase

or decrease all frequencies above or below their cut-o frequency. The cut-o

frequencies of the upper and lower band are 12 kHz and 80Hz respectively.

Themid band is congured as a peak lter with a center frequency of 2.5 kHz.

Unlikeshelving lters, the peak lter processes a frequency range that extends

upwards and downwards around its middle frequency.

LOW CUT

In addition, the mono channels are equipped with a steep LOW CUT lter

(slopeat18 dB/oct., -3 dB at 75 Hz) designed to eliminate unwanted

low-frequency signal components. These can be noises created by

hand-held microphones, subsonicnoise or plosive sounds created by highly

sensitivemicrophones.

FX sends enable you to feed signals via a variable control from one or more

channels and sum these signals to a bus. The bus appears at the console’s FX send

output and can be fed from there to an external eects device. The return from

the eects unit is then brought back into the console on the stereo channels.

Each FX send is mono and features up to +15 dB gain.

As the name suggests, the FX sends of the XENYX mixing consoles are intended to

drive eects devices (reverb, delay, etc.) and are therefore congured post-fader.

This means that the mix between dry signal and eect remains at the level

determined by the channel’s aux send, irrespective of the channel fader setting.

If this were not the case, the eects signal of the channel would remain audible

even when the fader is lowered to zero. With XENYX mixing consoles, the channel

fader is called LEVEL control.

In the 1202FX/1002FX, the FX send is routed directly to the built-in eects

processor. To make sure that the eects processor receives an input signal,

youshouldn’t turn this control all the way to the left (-∞).

PAN

The PAN control determines the position of the channel signal within the stereo

image. This control features a constant-power characteristic, which means the

signal is always maintained at a constant level, irrespective of position in the

stereo panorama.

LEVEL

The LEVEL control determines the level of the channel signal in the main mix.

◊ Attention: Since the FX path for the effect processor is connected

post-fader, the LEVEL control has to be turned up in order to get this

channel’s signal to the effects processor!

CLIP

The CLIP-LED’s of the mono channels illuminate when the input signal is driven

too high, which could cause distortion. If this happens, use the GAIN control to

reduce the preamp level until the LED does not light anymore.

2.2 Stereo channels

Fig. 2.2: Connectors and controls on the stereo channels

LINE IN

Each stereo channel has two balanced line level inputs on ¼" connectors for left

and right channels. If only the connector marked “L” (left) is used, thechannel

operates in mono. Thestereo channels are designed to handle typical line level

signals. Both inputs will also accept unbalancedconnectors.

The FX send of the stereo channels functions similar to that of the mono

channels. However, since the FX send bus is mono, a mono sum is rst taken from

the stereo input before it is sent to the FX bus.

BAL

The BAL(ANCE) control determines the levels of left and right input signals

relative to each other before both signals are then routed to the main stereo mix

bus. If a channel is operated in mono via the left line input, thiscontrol has the

same function as the PAN control used in the mono channels.

LEVEL

The LEVEL control determines the volume of the channel being sent to the

mainmix.

+4/-10

The stereo inputs of the XENYX have an input sensitivity switch which selects

between +4 dBu and -10 dBV. At -10dBV (home-recording level), the input is

more sensitive (requires less level to drive it) than at +4 dBu (studio level).

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Behringer Xenyx 1002FX Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Behringer Xenyx 1002FX

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info