660493
27
Verklein
Vergroot
Pagina terug
1/74
Pagina verder
27 X32 PRODUCER DIGITAL MIXER User Manual
5.8 Using Mute Groups
The X32 PRODUCER has 6 separate “mute groups”. Individual channels can be
assigned to these mute groups, allowing you to mute multiple channels with a
single buttonpush.
This is particularly useful in theater contexts, where groups of microphones
(suchas the ones belonging to a group of background performers) may need
to be muted and unmuted often. By assigning them to a mute group, you can
quickly mute/unmute a large group of channels, which is much faster than
muting/unmuting each channel one by one.
1. Press the MUTE GRP button.
2. While holding the desired Group button (located on top panel’s lower
right-hand corner), press the SELECT keys for any channels you wish to
assignto that mute group.
3. When you are done assigning channels to the mute group, press the MUTE
GRP button next to the display again. The channel SELECT buttons will now
work normally again.
4. Press the corresponding mute group button, on the console top panel to
mute that specic mute group and all channels belonging to it.
5.9 Mix Buses, Sub Groups and DCA Groups
On a live sound console such as the X32 PRODUCER, channels can be combined
into a single output channel in two ways.
A “Bus” is a combined collection of channel signals where each channel feeding
the bus can be done so with a variable level. One typical use of a bus would be
an eects loop (where for example, dierent channels feeding the bus and the
reverb eect associated with it, do so at dierent levels, so that a snare drum
has a small amount of reverb applied while a lead vocal has a large amount of
reverb). Another use of a bus would be to feed a stage monitor. By feeding the
monitor mix with a bus, dierent channels can feed the monitor bus at diering
levels, allowing creation of a custom monitor mix that is “just right” for the talent
on stage.
A “Group” is similar to a Bus, except that all channels feeding the group do so at
a ”unity gain” level, with their respective levels the same as their levels feeding
the main mix bus. Thus, a group is best used to control the levels of a group of
signals using a single fader, such as controlling the level of an entire group of
drum microphones.
To quickly divide up which of the 16 mix buses are congured as regular buses,
and which are congured as groups, press the SETUP button and page right to the
CONFIG page. Adjust the fth encoder to select between dierent combinations
of buses and groups for the 16 mix outputs of the console. This setting can later
be changed individually for each of the 16 mix buses either on the SETUP page
of the corresponding mix bus or individually per channel on the SEND page of
the selected channel. You can feed the signal of any mix bus either directly to
the main bus or back to any input channel if you want to apply loop type eects
or send to a monitor mix. All mix buses are available as SOURCE on a channel’s
CONFIG page.
Lastly, the X32 PRODUCER oers a “DCA Group”. This is similar to a normal group,
except that the signals of the underlying channels are not actually combined
into a single audio path. Instead, channels are assigned to a DCA group (short
for “DigitallyControlled Amplier” ) and when a single fader representing the
DCAgroup is moved, it has the eect of adjusting the level of all the underlying
channels assigned to that DCA group.
DCA groups are useful in situations where you have a collection of similar
signals, and you want to be able to quickly adjust their overall level, but also
easily adjust the individual levels of the individual channels assigned to the DCA
group. Forexample, say you have a concert that employs 4 separate background
vocalists. By assigning them all to DCA group 1, you can adjust their overall level
as desired in the FOH mix by adjusting DCA fader 1. However, if you then notice
that background vocalist #3 is a little too soft in the “blend” of background
vocals, you can adjust the level fader on their specic channel.
To create a DCA group on the X32 PRODUCER:
1. Press the GROUP DCA 1-8 button on the output fader layer.
2. Hold the respective DCA Group Select button on the right-hand side of
theconsole.
3. While still holding down the DCA Group Select button, press the SELECT
buttons for all the input channels, aux channels, fx return channels, and bus
masters that you wish to assign to said DCA Group. Those channels are now
assigned to the DCA group.
4. You can also press the DCA Group Select button in order to check which
channels are already assigned to it; the assigned channel SELECT buttons will
light up.
5. To adjust the level of a DCA group, simply adjust its respective fader.
DCA groups can also have custom names, colors, and icons assigned to them tohelp
you remember what groups of signals are assigned to each of the 8DCAgroups.
1. Press the SETUP button, then page right to the DCA GROUPS page.
2. Adjust the rst encoder to select the DCA group you wish to customize,
thenpress the encoder to edit.
3. On the editing pop-up window that appears, use the various encoders to
select a color, icon, and preset or custom name for the selected DCA.
4. Press the sixth encoder to exit the editing screen.
By contrast, conventional “groups” are useful when you have a group of signals
that you wish to combine into a single signal, perhaps to send that combined
signal to a single eect processor. For example, a common method for making
drums sound punchy and aggressive in a rock and roll mix would be to combine
all of the drum channels to a single stereo group, then process that group signal
through a compressor, and then nally bring the mono or stereo compressed
drum group back into the mix. This approach would not be possible with a DCA
group, because the DCA is not actually combining the audio signals, it is merely
linking the levels of all of the underlying channels digitally.
5.10 User Assignable control section
The X32 PRODUCER’s assignable controls section lets you take the adjustments
you make most often, and assign them to a group of dedicated controls that are
assignedto just those functions, and nothing else. The assignable controls oer
8 buttons for a variety of functions.
Setting up the assignable controls is easy:
1. Press the “view” button in the assignable controls section. The main screen
will switch to a view that lets you make assignments for the custom controls.
2. The main screen will show assignments for all 3 sets of custom controls
(A, B, and C) on one page. Rotate any of the rst ve encoders to move the
orange “focus” box to the specic set of custom controls you wish to assign.
3. Press any of encoders 1-5 to switch to the edit screen for the specic custom
control that you have highlighted. The main screen will switch to an editing
screen where you can assign a console parameter to the custom control.
4. Adjust and press the encoders 3-6 on the editing screen from left to right to
make a custom control assignment.
5. When you are nished, you will see that the LCD screen located in the
custom controls section reects the assignment you have made in both
screen color and text.
6. You are now free to use and enjoy the custom assignments you have made.
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Behringer X32 Producer bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Behringer X32 Producer in de taal/talen: Engels als bijlage per email.

De handleiding is 9,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Behringer X32 Producer

Behringer X32 Producer Snelstart handleiding - Deutsch, English, Français, Português, Espanõl - 31 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info