Handleiding Behringer X32 Compact (pagina 27 van 74) (Engels)

660491

Verklein

Vergroot

Pagina terug

1/74

Pagina verder

27 X32 COMPACT DIGITAL MIXER User Manual

5.4 How do I add one of the 8 internal eects

to the sound?

There are two types of eects that are commonly used:

• “Eects Loop” (side chain) style eects, where multiple channels all send

varying amounts of their signal to a common eect, such as a reverb,

delay,or chorus.

• “Insert” style eects that are inserted in to the signal path of a single

channel of audio. Examples would be a graphic EQ, lter, exciter,

ortubeemulator.

To apply an “Eects Loop” style eect:

• Press the “FX” menu button. The main screen will show the FX home screen

where dierent eects processors are assigned to the 8 processing slots.

• Adjust rotary encoder #6 to highlight the rst eects processor; it will be

surrounded by an orange outline.

• Adjust rotary encoder #1 and rotary encoder #2, selecting your desired bus as

the source for both the left and right inputs of the rst eect processor.

• Adjust rotary encoder #5 to select a specic eect processor,

suchas “Ambience”.

• Select the fader bank button labeled “Eects Returns” on the left side of the

console. Bring the faders labeled FX1L and FX1R up to 0 dB in case they are

not set to this value by default. In the initial setup, these returns are stereo

linked and automatically send to the main LR bus, but it is also possible to

send them to the other buses as well. For this, press the HOME button next

to the screen while the return is selected, then go to the SENDS tab with

the PAGE SELECT right button and adjust the send levels for the return to the

other buses, oruse the dedicated BUS SENDS controls.

• Back on the EFFECTS page, press the PAGE SELECT right button to switch the

screen to the editor for the Ambience processor. The screen will switch to an

editor page for the rst processor. Adjust the rotary encoders to tailor the

eect to your liking.

• To apply the eect to assorted input channels, select an input channel,

thenadjust its “Bus Send” knob to taste. As the bus send level is increased,

more of the channel signal will be sent to the Ambience eect. Repeat this

process with other channels you wish to send to the Ambienceprocessor.

To apply an “insert” style eect:

• Press the “EFFECTS” menu button.

• As the eects on the left side are also able to handle complex send eects

like reverb, the slots on the right side shall be used for insert eects like

limiter, graphic EQ, etc. You can also use insert eects on the left side,

butthis will limit your use of reverbs and other processor-intensive eects.

• Adjust rotary encoder #6 to highlight one of the eects processors on the

right side; it will be surrounded by an orange outline.

• Adjust rotary encoder #1 and rotary encoder #2, selecting “Insert” as the

source for both the left and right inputs of the eect processor.

• Adjust rotary encoder #5 to select a specic eect processor, such as

“precision limiter”.

• Select the specic input or output channel you wish to use the inserted

eect on.

• Press the HOME button, then the PAGE SELECT right button to navigate to the

selected channel’s “Cong” screen.

• Adjust rotary control #6 to select the specic processor you have applied the

eect to, in this case “Ins FX 5L”. Press the encoder to connect the selected

insert eect.

• The Precision Limiter is now applied as an insert on the selected channel.

Sending more than one channel through the same insert eect is, of course,

prohibited. There will be a warning when you try to insert an eect slot that

has already been used as an insert on any other channel. Both sides of a dual

type eect can be used as inserts on dierent channels or buses.

5.5 How do I use an outboard

eectsprocessor?

In some situations, you may wish to use a loop-style eect provided by an

external eect processor, as opposed to using one of the eight built-in processors.

To do so:

• Press the ROUTE button, page right to the “Aux Out” screen, and adjust the

rst and fourth encoders to tie a rear panel ¼" aux out, such as Aux Out 1,

toan available mix bus, such as Mix Bus 2.

• Patch rear panel Aux Output 1 to the input of your external eects processor.

• Patch the output of the external eects processor to rear panel Aux Input 1.

• Select the “Aux In/USB” layer, select the “Aux 1” channel, and make sure the

stereo button is lit so that the Aux 1 return signal is assigned to the main

LR bus.

• Move the Aux 1 channel fader to 0 dB.

• Adjust the settings on the external eects processor to taste.

5.6 How do I set up live stage monitoring?

Setting up a live stage monitor mix using conventional monitors:

1. Press the ROUTE button and page right to the Analog Out page.

2. Adjust the rst encoder to select a rear panel analog output (e.g. Output 1),

then adjust the fourth encoder to select a mix bus (e.g. Mix Bus 1). Whenthe

source and destination have been selected, press the 4th encoder to

complete the assignment.

3. Adjust the 5th encoder to set up the monitor send as pre-fader, or pre/post

EQ. This will prevent the monitor mix from changing when the front-of-

house mix is adjusted.

4. Connect a cable from rear panel analog Out 1 to the input of:

a) A powered stage monitor

b) An external amplier feeding a passive stage monitor

c) A transmitter for a set of wireless in-ear monitors

5. On the bank of output faders on the right hand side of the console, selectthe

monitor bus (1-8, 9-16) (in this case Bus 1) and adjust the fader to 0 dB

initially. You can change the overall output level on this bus anytime later,

ofcourse.

6. To adjust the mix sent to the monitor, select an input channel, then adjust

its “Bus Master 1” fader. Repeat for the other input channels to complete the

monitor mix.

The monitor mix can also be adjusted using the X32 COMPACT’s

“Sends on Faders” function:

1. On the bank of output faders on the right hand side of the console,

selectthemonitor bus (1-8, 9-16) that feeds the talent’s stage monitor

(inthis case Bus 1).

2. Press the “Sends on Faders” button. You will see the button illuminate.

Behringer X32 Compact Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Behringer X32 Compact

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info