Handleiding Behringer X32 CORE (pagina 11 van 29) (Engels)

660492

Verklein

Vergroot

Pagina terug

1/29

Pagina verder

11 X32 CORE DIGITAL RACK MIXER User Manual

Gated Reverb

This eect was originally achieved by combining a reverb with a noise gate.

Ourgated reverb creates the same impression by a special shaping of the reverbtail.

Gated Reverb is especially eective for creating a 1980s-style snare sound or to

enlarge the presence of a kick drum. (Inspired by the Lexicon 300/480L)

PRE DELAY controls the amount of time before the reverberation is heard following

the source signal. DECAY controls the amount of time it takes for the reverb to

dissipate. ATTACK controls how fast the reection density builds up. DENSITY shapes

the reverb decay tail. The higher the density, the greater the number of sound

reections. SPREAD controls how the reection is distributed through the envelope

of the reverb. The LO CUT knob sets the frequency beneath which the source signal

will not pass through the reverb. The HiSvFr/ HiSvGn knobs adjust a Hi-Shelving lter

at the input of the reverb eect. DIFF(USION) controls the initial reection density.

Plate Reverb

A plate reverb was originally created by sending a signal through a transducer

to create vibrations on a plate of sheet metal which were then picked up as an

audio signal. Our algorithm simulates that sound with high initial diusion and a

bright colored sound. X32’s Plate Reverb will give your tracks the sound heard on

countless hit records since the late 1950s. (Inspired by the Lexicon PCM-70)

PRE DELAY controls the amount of time before the reverberation is heard

following the source signal. DECAY controls the amount of time it takes for the

reverb to dissipate. SIZE adjusts the size of the virtual room created by the reverb

eect. The DAMP knob adjusts the decay of high frequencies within the reverb

tail. DIFF(USION) controls the initial reection density. The LO CUT knob sets the

frequency beneath which the source signal will not pass through the reverb.

The HI CUT knob sets the frequency above which the source signal will not pass

through the reverb. The BASS MULT(IPLIER) knob adjusts the decay time of the

bass frequencies. XOVER controls the crossover point for bass. MOD DEPTH and

SPEED control the intensity and speed of the reverb tail modulation.

Hall Reverb

Classic Hall Reverb simulates the reverberation that occurs w hen sound is

recorded in medium to large-sized concert halls. Use the Hall Reverb to give your

mix a lush, three-dimensional quality that will make your performance sound

larger than life. (Inspired by the Lexicon Hall)

The PRE DELAY slider controls the amount of time before the reverberation is

heard following the source signal. DECAY controls the amount of time it takes for

the reverb to dissipate. SIZE controls the perceived size of the space being created

by the reverb eect. The DAMP slider adjusts the decay of high frequencies within

the reverb tail. DIFF(usion) controls the initial reection density. SHAPE adjusts

the contour of the reverberation envelope. 

Vintage Room

Vintage Room simulates the reverberation that occurs when sound is recorded in

a small room. When you want to add a bit of warmth and just a touch of reverb,

X32’s Vintage Room breathes life into close-miced guitar and drum tracks.

(Inspired by the Quantec QRS)

The VU meter displays the input and output levels. Set the early reection times

for the left and right channel with ER DELAY L and ER DELAY R. ER LEVEL sets the

loudness of the early reection level. REV DELAY controls the amount of time before

the reverberation is heard following the source signal. HI/LOW MULTIPLY adjusts the

decay time of the high and bass frequencies. TIME shows the duration of the reverb

eect. ROOM SIZE adjusts the size of the room eect being created incrementally

from small to large. HIGH CUT sets the frequency above which the source signal

does not pass through the reverb. DENSITY manipulates the reection density in the

simulated room. (This slightly changes the reverb decay time). LOW CUT sets the

frequency below which the source signal does not pass through the reverb.

Vintage Reverb

Based on the legendary EMT250, X32’s Vintage Reverb delivers shimmering

bright reverb that won’t drown out or overpower your live or recorded tracks.

UseVintage Reverb to sweeten vocals and snare drums without sacricing clarity.

When layer 1 is selected, the rst slider on the left sets the reverb time from

4milliseconds to 4.5 seconds. Slider 2 controls the low frequency multiplier

decay time. Slider 3 controls the high frequency multiplier decay time. Slider 4

controls the amount of modulation in the reverb tail. When layer two is selected,

slider1adjusts the pre delay. Slider 2 selects the low cut frequency. Slider 3

selects the Hi Cut frequency. Slider 4 adjusts the output level of the reverb.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Behringer X32 CORE Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Behringer X32 CORE

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info