660483
8
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
8 REFERENCE AMPLIFIER A500 User Manual
3.2 Mono-bridged mode
In this mode, the voltages of both channels are added up and routed to just
one loudspeaker. This results in a doubling of voltage, quadrupling of the peak
power value and roughly trippling of the continuous power output on a single
channel. The input and the gain control on channel 1 are used in mono-bridged
mode. Thechannel 2 control elements are not used. ATTENTION: To avoid
cancellations due to internal phase inversion, the GAIN control on
channel 2 must be turned all the way to the left!
Use this operating mode to feed the output of both channels into a single 4-Ohm
load. Set the STEREO/BRIDGED MONO switch (8) to “BRIDGED MONO.
Please only connect the speaker using the BRIDGED MONO connector (9) or by
using both of the middle binding posts(10).
Always power the A500 down using the POWER switch whenever you
make any changes to the operating mode settings.
Keep in mind the minimum load impedance of 8 Ohms in
mono-bridged mode.
BB410
Input
Channel 1
BASS V-AMP PRO
Bass
REFERENCE AMPLIFIER A500
Fig. 3.2: Mono-bridged operation
If your amp is overdriving for a longer period of time, it may become
muted for several seconds at a time. Always select appropriate volume
values to avoid overdriving.
Safety precautionsv for mono-bridged operation
A voltage of up to 60 V RMS is present between the output connectors of the
A500. Always adhere to all appropriate safety precautions when connecting your
speakers to avoid the risk of electric shock.
Running your amp in mono-bridged mode puts both the amp and your
loudspeakers under additional strain. Excessive overdriving can result in
premature shutting down of the unit itself or permanent damage to the speakers.
Make sure that your speaker (impedance at least 8 Ohms) and the cables you use
can indeed handle the power load fed into/through them.
4. Installation
4.1 Installation in a rack
Your A500 can be installed into a 19" rack and requires
two rack spaces. Please use four attaching screws and washers for installation.
Reinforce the back end, especially for on-the-road use. Please ensure that
enough cool air reaches the rack, especially if other rack equipment generates
a lot of heat. Due to its weight, we recommend installing the A500 in the lower
portion of your rack. If you are installing several amps in a single rack, you should
leave some space between individual amps (approx. 1 height unit) to allow for
sucient cooling.
The A500 has massive heat sinks on its side frame that guarantee
reliable operation. Never block air supply to these heat sinks because
excessive heat may damage the components inside your amp.
Even though the protective circuitry guards the inside components
from damage caused by excessive internal temperatures, you should
still double-check where the amp is placed and inspect cable
connections if you are experiencing thermal protection dropouts.
4.2 Connections
Inputs
If you wish to use XLR connections for unbalanced input signals, connect the
unused pin on the XLR connector (pin 3) with the ground. No modication is
needed if using mono jacks (also see ch. 4.3).
Should you register distractive signals such as noise or hissing,
we recommend separating the amp input from the signal source.
This way, you can quickly determine if the noise originates
in the equipment connected to the amp. Always make sure
to completely lower amplification of both channels before
powering up the amp (GAIN control turned all the way to the left).
Otherwise, permanent damage to your speakers may occur.
Outputs
Your A500 oers several output connection possibilities: two ¼" TS mono
connectors and two pairs of touch-safe binding posts. Inaddition to both
¼"TS mono connectors for individual channels, the A500 also features an extra
¼"connector for use in mono-bridged mode.
Whenever possible, use thick and short speaker cables to minimize
power losses. Never route output cables near input cables.
When using binding posts, make sure that the wire insulation is not stripped
more than what is necessary, and that wires are completely inserted into the
binding post so that no bare wire is visible. Cable clamps must be isolated to
avoid the possibility of electric shock. When running the amp in mono-bridged
mode, always use the middle two binding post connectors, paying attention to
correct polarity.
ATTENTION! If you notice bare cable endings on the binding post
connectors, disconnect the AC mains and remedy the improper output
connection before powering the amplifier on again.
Connecting to the mains
Always connect your power amplier to the voltage specied on the rear of
the unit. Connecting the amp to incorrect voltage can permanently damage it
(alsosee ch. 2, under [11] FUSE SWITCH/VOLTAGE SELECTION).
Before powering up the amplier, double-check all connections and fully lower
the gain settings.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Behringer A500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Behringer A500 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Behringer A500

Behringer A500 Gebruiksaanwijzing - Nederlands - 11 pagina's

Behringer A500 Gebruiksaanwijzing - Deutsch - 11 pagina's

Behringer A500 Snelstart handleiding - Deutsch, English, Français, Português, Espanõl - 11 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info