Handleiding BeF Home Passive - HOT AIR FIREPLACE INSERTS (pagina 2 van 9) (Engels)

810623

Verklein

Vergroot

Pagina terug

1/9

Pagina verder

________________________________________________________________________________________________________________________________

Firma: BeF Home, s.r.o. Strana 2 (celkem 9) Platí od: 1. 4. 2014

Vydání: 4

Information about the combustibility level of some construction materials:

The combustibility level of the construction material

A incombustible – granite, sandstone, concrete, special pargeting, bricks, ceramics facing

B hardly combustible - gypsum plasterboard

C1 hard combustible – leafy wood, plywood, hardened paper

C2 medium combustible – cork sheets, indie-rubber, floor material

C3 light combustible – wood-fibre sheets, polystyrene, polyurethane, PVC

Position:

Fireplace inserts can be positioned only in rooms and in places which are risk free. There must not be any electric wires in walls and in

ceilings where a jacketed chimney insert is installed. In rooms where a fireplace insert is situated there must be sufficient fresh-air inlet for

combustion if the fireplace insert isn’t connected to external air input. The base where the fireplace insert is situated must be made and must be

large enough to allow the firebox work correctly.

Fireplace inserts must not be located:

 on stairways (excerpt houses where a maximum of two flats are situated)

 on corridors open to the public

 in rooms, where easily combustible or explosive materials or mixtures are stored or manufactured

 in flats or areas which are aired only by means of ventilators or hot-air heaters when a safe function of an open fire is not ensured

 with the help of the recommended stand and tube

Heating output:

Bear in mind the information written on the insert design description. The heating potential of the fire depends on the output stated. Output is

applicable to rooms which correspond to the Heat Safety Protection. In rooms which are more than 200 cubic metres it is necessary to count

the heat consumption.

Fireplace insert location and combustion air inflow:

 The area must be provided with at least one door which leads into an open space, or with a window which can be open, or it must be

connected with other rooms. Only rooms of the same flat or dwelling are counted. If there is not enough the room where the

fireplace insert is located, must be provided with a tube:  which leads directly into the fireplace insert (see pict. 3) and supplies

minimum volume of convectional air. When the fireplace insert is connected with outer air it must be installed on the original stand

which is supplied by manufacturer. - it is necessary to take deformation resistance into account during tubing batching, especially

during curve, branch pipe or long pipe installation.

 for combustion air which leads into an open space and supplies at least 360 m³/hour of combustion air 1 m² of firebox hole (see pict.

02). This tube must be connected directly with the fireplace insert. If other fireboxes are located in a heating interconnection at least

540 m3 of combustion air 1 m² must be supplied into the firebox. To other fireboxes except this at least 1.6 m³ of combustion air /

hour and on each kW of total nominal heat output when the initial pressure difference was at least 4 Pa as compared to an open space

are needed (except fireboxes which are located in areas that do not depend on air in a room, do not need a smoke flue or are located

in areas where the operating safety of inserts cannot be endangered).

 if the fireplace insert isn’t connected to external air input, it is recommended that combusting air is supplied towards a fireplace in a

convection area. - it is necessary to arrange tubing for combusting air in buildings with more than two floors, as stipulated by local

building regulations, and tubings for combusting air which connect antifire walls, so that fire and smoke cannot spread into other

floors or fire compartments.

It is possible to use data from the Equipment Certificate when setting the dimension of combusting air flow piping

(inflow of air/hour)

Ask your chimney sweep or fireplace builder for assistance.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

BeF Home Passive - HOT AIR FIREPLACE INSERTS Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info