76530

Baumatic BWD 12.1 Handleiding

31
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
Is
BWD12.1
Fully integrated
washer dryer
USER MANUAL FOR YOUR BAUMATIC
BWD12.1
Fully integrated washer dryer
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference.
DD 07/03/11
2
3
Contents
Environmental note 4
Important safety information 5 - 6
Specifications 7
Description of the appliance 8 - 11
Control panel 9
Program options 9
LCD display 10
Detergent drawer 11
Preparing the wash cycle 12 - 16
Preparing your garments for washing 12
A selection of wash care symbols 13
Detergents and conditioners 13 - 14
Program table 15 - 16
Wash program guidance 16
Selecting a wash program 17 - 18
Selecting a separate drying program 18
Selecting an automatic wash and dry program 19
Cancelling or pausing a wash program 19 - 20
Delay start feature 20
Spin reduction button 20 – 22
Setting a program option 22 – 23
Child lock 23 - 24
Maintenance and cleaning 24 - 26
In daily use 24
Control panel and washing machine cabinet 24
Detergent drawer 25
The washing machine drum 25
Door gasket 26
Error code failure system 26 - 27
General troubleshooting 27 - 28
Poor wash results 28 – 29
Removing stains 29
Stain removal rules 29
Stain removal guide 30 - 31
Cleaning the drain pump filter 31 - 32
Installation 33 - 38
Unpacking and removing the transit bolts 33 - 34
Positioning and levelling the appliance 34 - 35
Connecting to the mains water supply 35 - 36
Water outlet 36
Fitting the furniture door 36
Power supply 37
Before first use maintenance wash 38
Contact details 39
ENVIRONMENTAL NOTE
Note
: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any plug
useless. Cut the cable off directly behind the appliance to prevent
misuse. This should be undertaken by a competent person. Disable
the door lock to make sure that children cannot get stuck inside
the appliance.
4
IMPORTANT SAFETY INFORMATION
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If you
are unsure of any of the information contained in this
booklet, please contact the Baumatic Advice Line.
General Safety
o Repairs to your appliance must only be carried out by a
Baumatic engineer or one of its authorised service agents. Any
attempt by an inexperienced person to repair the appliance,
could result in injury or damage to your washer dryer.
o If you notice that the mains cable is damaged. The appliance
must not be used. The same applies if you notice that the
worktop, control panel or base areas are damaged. As this could
allow access to the internal components of the machine.
o The appliance should be turned off and isolated from the mains
supply, before either cleaning or maintenance work is attempted.
o The mains cable must not be used to pull the plug out of the
electrical socket.
o The machine should not be sprayed with water.
o The glass of the porthole door may become hot during the higher
temperature wash programs.
o The machine should be allowed to cool before carrying out an
emergency drain or cleaning the drain filter.
o It is possible for small animals to chew either mains cables or
water hoses, which could cause an electric shock hazard or leak.
Installation
o The installation instructions contained within this user manual
must be followed.
o It is obligatory for the completed installation to comply with all
relevant building regulations and local water authority
requirements.
5
6
o Before the first use of the appliance, we advise that a 90
degree cotton wash is completed. No garments should be
placed inside the machine; however a small amount of
detergent must be used.
During Use
o It is recommended that the appliance is unplugged and the
water supply is turned off after the machine is used.
o This appliance is only designed to wash normal domestic wash
loads. If you use your washing machine in any other way or it is
incorrectly used, then Baumatic accepts no liability for any
damage that might be caused and any guarantee will be void.
o No attempt should be made to alter or modify the specifications
of this appliance.
o The detergents that you place in this appliance should be
suitable for automatic washing machines. With regards to dosage
levels, the detergent manufacturer’s recommendations should be
followed.
o You should not wash garments that have been in contact with
flammable materials.
o Your washing machine should not be used for dry cleaning.
o If you use either dyes or bleaching agents inside this machine,
then you should consult with the manufacturer of these products
to make sure they are suitable for use in your washing machine.
Baumatic cannot be held responsible for any damage that may
result.
Child Safety
o Your washing machine should only be used by adults. You should
not allow children in the area of the machine unsupervised. You
should not let them touch the controls or play with the appliance.
o It could be possible for a child or pet to gain access to the
washing machine through the porthole door. Therefore please
check the drum before using the appliance.
o Any packaging that is removed from the machine should be kept
away from children.
o All detergents should be kept out of children’s reach in a safe
place.
Specifications
9 13 wash programs/2 drying programs
9 6kg wash load/3kg drying load
9 1100 rpm maximum spin speed
9 LCD display
9 Delay start timer with remain time indicator
9 3 Option buttons: Easy iron
Extra rinse
Intensive wash
9 Unbalance control system
9 Foam protection
9 Suspend the clothes in water option
9 Door safety lock
9 Child lock
9 Stainless steel drum
9 Adjustable feet
9 Error code failure system
9 Aqua Spray rain shower effect- This additionally showers the
wash load throughout the wash cycle. It helps to improve the
wash and rinsing efficiency.
Appliance dimensions Aperture dimensions
Height: 820 – 850 mm 820 mm
Width : 590 mm 600 mm
Depth: 550 mm 600 mm
Energy efficiency
Energy rating B
Wash performance A
Water extraction performance C
7
Description of the appliance
8
Control panel
Wash program selection knob
This control knob allows you to select the wash program of your
choice. To activate it you should press in the program selection knob,
to pop out the control.
Start/Stop button
Once a wash program has been selected, this button should be
pressed to start the wash cycle.
Program option button
This button needs to be pressed after a wash program has been
selected, but before the wash program has been started. If you
select a different wash cycle after pressing a program option, it
will need to be reselected.
Extra rinse: This function increases the level of the final rinse for the
selected wash program. This should be selected if large loads are being
washed or the garments belong to somebody who has sensitive skin.
This option will increase the amount of water the appliance uses.
Easy iron: This function helps to prevent garments from creasing by
carrying out a program where the rotation of the drum will fluff out the
garments, after the spin cycle has completed. This should make the
garments easier to iron.
Intensive wash: This function should be selected if you are washing
heavily soiled, stained clothes. It achieves a better level of wash
performance by extending the wash program that you have selected.
9
LCD display
1. Wash program phases:
o Prewash
o Wash
o Rinse
o Spin and drain
o Drying
2. Spin speed.
3. Program number (for a few seconds) and then program
duration.
4. Program options:
o Easy iron
o Extra rinse
o Intensive wash
10
Detergent drawer
Pre wash section
This compartment should have detergent placed in, if you are going to
select a wash program that has a pre wash as part of it.
Main wash section
This compartment should have detergent placed in it (you should also
put a water softening agent in this section, if you use one). The
detergent will be added to the drum at the start of the main wash
program.
Conditioner section
This compartment should be used for liquid conditioners (fabric
softener, starch). They will be added to the wash load during the final
rinse.
11
Preparing the wash cycle
Preparing your garments for washing
o Your washing should be sorted out, according to
the fabric type and the wash care symbol that is
printed on the garment’s wash care label. (see
separate section on wash care symbols).
o Your washing should also be sorted out
according to the degree of soiling.
o Check all pockets on a garment to make sure
that they are empty.
o Remove any detachable metal items (badges,
paperclips, safety pins etc).
o Zips should be closed, duvet covers and pillow cases should be
buttoned up and any loose straps should be tied up. This will
help to prevent other garments from getting damaged during the
wash.
o Woollens and knitted coloured fabrics should be turned inside out
before being washed in the appliance.
o Small delicate items (tights, baby socks) should be placed in
either a washing net or a zipped pillow case. Bras suitable for
machine washing, that contain a wire, should also be washed in
this manner.
o Curtains should be handled with particular care. All plastic hooks
or metal strips must be removed before being washed in the
appliance.
12
o Coloured items and whites should be washed
in separate wash cycles.
o New garments often contain an excess of
dye, therefore it is advisable to wash them separately for their
first wash.
o Garments should be unfolded and shook out before being placed
inside the machine.
A selection of wash care symbols
Washing
Boiling
temp
95°C
Normal
temp
60°C
Normal
temp
40°C
Do not
wash!
Bleachable
in cold
water
Do not
bleach!
Wool
seal
Dry
cleaning
Delicate
temp
30°C
Delicate
temp
40°C
Hand
wash
only
All
solvents
All but TRI
Benzine
only
Do not
clean!
Spin
dryer
Normal
Low
High
Do not
dry!
Hang to
dry
Drip dry
Dry
flat
Ironing
110°C
150°C
200°C
Do not
iron!
o The wash care symbols should be used to help you to select the
most suitable wash program. They will also help you to sort your
laundry into different loads, depending on the fabric type and the
highest temperature which the garment can be washed at.
o If the wash care label does not appear in the above table, then
please refer to the washing machine program chart. This gives
more detailed descriptions of the types of fabric that are suitable
to be washed using a particular wash program.
Detergents and conditioners
The amount of detergent that you need to use in your appliance, will
depend on
o The degree of soiling. Lightly soiled garments in general
require less detergent.
o The size of the wash load. A smaller wash load will require a
reduction in the amount of detergent.
o The hardness of your tap water. The harder your water is,
then the more detergent you will need to use. The detergent
manufacturers normally give guidance as to how much extra
detergent should be used, depending on the hardness of the
water.
13
Liquid detergent
If you are using liquid detergent, then in the majority of cases the
liquid should be placed inside the dosing device supplied by the
detergent manufacturer. All instructions on the detergent packaging
should be followed.
Water softening agents
If your tap water is hard, then it may be prudent to utilise a water
softening agent. This will help to ensure that the appliance does not
become clogged with hard water deposits. You may also find that it will
allow you to lessen the amount of detergent that you are using.
When using any detergent or water softening
agent, the recommendations of the
manufacturer should be followed.
14
15
16
NOTE: the KWh and litre consumptions and program durations may
vary depending on the type and amount of clothes being washed, your
mains water pressure, etc.
(*) Program for wash and energy consumption assessment, in
accordance with standard EN60456 (press intensive wash button).
Wash program guidance
o A particular program option can only be selected if the program
table advises that it is possible with the wash cycle you have
selected.
o The washing machine automatically selects a spin speed for a
particular wash program. However it is possible to reduce the spin
speed by using the spin reduction feature.
o Important: You should make sure that the selected spin speed is
appropriate for the garments that you are washing.
o If you use the spin reduction feature, you can make the machine
not go into a spin cycle. If you pick this option, then the machine
will stop with water in the drum.
o Important: Before opening the door of the appliance, you MUST
select the drain program to clear this water.
o The LCD display shows an approximate time for the selected wash
cycle. Please note that factors external to the machine, e.g. the
temperature of your water supply, your water pressure etc. can
affect the time it takes for the wash cycle to complete.
Selecting a wash program
9 Load your laundry and put detergent in the relevant
compartment of the soap drawer.
9 Close the porthole door firmly.
9 Activate the pop out
program selector knob by
depressing it.
17
9 Select the most
appropriate wash program
for the garments that you
are washing, by turning the
program selector knob.
o The LCD display will briefly flash the wash program number that
you have selected and then show the approximate time that it
will take the chosen wash cycle to complete.
9 Select any program options by using the program option button
underneath the LCD display (for more information, please refer
to the “setting a program option” section).
o Any program option that you select, will affect the length of time
that the wash cycle will take to complete. The LCD display will
update to reflect this change.
9 Press the Start/Stop button.
o After approximately 5 seconds, you will hear your washing
machine start the wash cycle.
o If there is a power failure or the plug is pulled out of the
socket when a wash cycle is in progress., The wash
program will continue, once power has been restored.
o Whilst the wash program is
in progress, the program
phase and time remaining to
the end of the wash cycle will
appear on the display.
o The active phases will appear at the top of the display, as the
wash program progresses. The time remaining until the end of
the program will update throughout the wash cycle. Please note
that it does not count down in “real time”.
o Any program option can be selected once the wash cycle is
already in progress, providing that the stage in the wash cycle
that the option will affect has not already passed. (E.g. you
cannot select an intensive wash, once the machine has reached
the rinse stage of the wash cycle).
Selecting a separate drying program
9 Activate the pop out program selector knob by depressing it.
o Select the most appropriate drying cycle for the garments
that you wish to dry, by turning the program selector knob.
o IMPORTANT: Please take note of the maximum size of
load that you can dry in this appliance. This information
is contained in the program chart.
18
sed.
o Select the drying time in
minutes, by using the
drying time button.
o The drying time will
appear on the LCD
display and will increase
each time the drying
time button is pres
o Press the START/STOP button to get the drying cycle to
commence.
Selecting an automatic wash and dry program
9 Activate the pop out program selector knob by depressing it.
9 Select the most appropriate wash program for the garments that
you are washing, by turning the program selector knob.
o The LCD display will briefly flash the wash program number that
you have selected and then show the approximate time that it
will take the chosen wash cycle to complete.
9 Select any program options by using the program option button
underneath the LCD display (for more information, please refer
to the “setting a program option” section).
o Any program option that you select, will affect the length of time
that the wash cycle will take to complete. The LCD display will
update to reflect this change.
o Select the drying time in minutes, by using the drying time
button.
o The drying time will appear on the LCD display and will increase
each time the drying time button is pressed.
o Press the START/STOP button to get the automatic wash and dry
cycle to commence.
o IMPORTANT: If you select a wash and dry program, your
wash load must not be over 4kg for NORMAL wash
programs and 1.5kg for DELICATE wash programs.
Cancelling or pausing a wash program
9 To stop a wash program once a wash cycle is in progress, you
should turn the program selection knob.
o The appliance will go onto PAUSE status and the wash program
will be cancelled.
o The door will remain locked for two minutes before it is possible
to open the door and take out the garments.
Before opening the porthole door, you MUST
drain the appliance; otherwise there may still
be water in the drum when you open the
door.
19
o It is also possible to put the machine into PAUSE status by
pressing the START/STOP button whilst the wash cycle is in
progress. However this will not cancel the wash program and to
restart the wash cycle, you should press the START/STOP button
again.
Delay start feature
Your appliance has a delay start feature, which allows you to pause
the start of a wash cycle until a later time.
9 Follow the process listed under “Selecting a wash program”
9 Before pressing the
START/STOP button, you
should select the length of
time that you want to
delay the wash program
for by pressing the delay
start button.
o Each time the delay start button is pressed, the start of the wash
cycle will be delayed by one hour. The LCD display will show how
many hours the wash cycle is being delayed for in the bottom
right hand corner.
o Press the START/STOP button.
o To cancel a time delay that has been set, you should press the
delay start button successively. Once 24 hours shows on the LCD
display, you need to press the delay start button one further
time and the delay start will be cancelled.
o If you alter the wash program whilst a delay start has been set,
this will also cancel the delay start.
Spin reduction button
Your washing machine will automatically select an appropriate spin
speed for each wash program. However it is possible to decrease
the spin speed that it automatically selects, by pressing the spin
reduction button.
9 Turn the wash program selection knob to the wash program
that you want to use.
20
9 Press the spin selection button and the spin speed will reduce
in 100 rpm increments.
o It is possible to reduce the spin speed from the one
automatically selected by the wash program, down to
400rpm.
9 If you continue to press the spin reduction button after
400rpm appears. Then will appear in the LCD display. This
means that the “No spin” option has been selected and at the
end of the wash cycle, the machine will not spin at all and the
wash program will finish after it has drained.
9 If you press the spin
reduction button again,
then will appear in the
LCD display. This means
that the “Anti-crease”
option has been selected.
The clothes will be held in
water, until you select a
spin or drain program.
9 This feature is useful if you are not going to be present when
the wash cycle completes, as it will lessen the chance of the
garments becoming creased.
9 After the appliance completes the last rinse, the
symbol will
flash and the drum will rotate approximately every 3 minutes.
9 Press the spin reduction button until the spin speed that you
require appears in the LCD display, then press the
START/STOP button.
21
9 If you want the appliance to drain only, press the spin
reduction button until the symbol appears in the LCD
display, then press the START/STOP button.
YOU MUST DO ONE OF THESE STEPS BEFORE
OPENING THE DOOR OF THE APPLIANCE.
OTHERWISE YOU COULD OPEN THE PORTHOLE
DOOR WHILST THERE IS STILL WATER IN THE
DRUM.
You should ensure that the garments you are
washing are suitable for suspending in water
before selecting this option. Garments should not
be suspended in water for a prolonged period.
Setting a program option
o There are three program options that you can select (providing
that the wash program chart indicates that a particular option
can be selected with a particular wash program).
o To select a program option,
you should press the
selection button until the
neon comes on next to the
program option that you
want.
o By pressing the select
button several times, you
can choose between
several combinations of
program option. One, two
or three program options
can be selected at a time,
depending on the wash
program that you have
selected.
o Any program option that you select, will affect the length of time
the wash cycle will take to complete. The LCD display will update
to reflect this change.
9 Press the START/STOP button.
22
o The program option button needs to be pressed after a wash
program has been selected, but before the wash program has
been started. If you select a different wash cycle after pressing a
program option, it will need to be reselected.
o Any program option can be selected once the wash cycle is
already in progress, providing that the stage in the wash cycle
that the option will affect has not already been passed. (E.g. you
cannot select an intensive wash, once the machine has reached
the rinse stage of the wash cycle).
Child lock
Your appliance has a child lock option, if this is set, it will mean that
nobody can affect the operation of the wash program once it has
started.
The child lock should be activated, once a wash program has been
selected and any program options that you wish to use.
o To activate the child lock, you should hold down the START/STOP
button for at least three seconds. When the child lock is set, a
symbol will appear on the LCD display.
o The child lock option will end once the wash cycle completes.
23
o If you want to cancel the child lock option before the wash
program completes. You should hold down the START/STOP
button for at least three seconds. When the
symbol
disappears from the LCD display, the child lock option has been
cancelled.
Maintenance and cleaning
In daily use
9 Once a wash cycle has completed, you should pull out the
detergent drawer slightly, so it can dry out.
9 Leave the porthole door ajar for a short while after a wash
cycle has completed. This should help to prevent stagnant
smells and to protect the door seal.
9 Close the water tap.
9 We suggest that you disconnect the appliance from your
mains supply, when it is not in use.
Control panel and washing machine cabinet.
IMPORTANT: Do not use any abrasive cleaner or household polish on
either the control panel or operating parts.
9 Wipe over the control panel and the external surface of the
machine using a brand new damp cloth with warm water.
9 If you ever spill any liquid detergent or conditioner from the
detergent drawer onto the washing machine cabinet, then
these should be cleaned up immediately as they could be
corrosive.
24
Detergent drawer
Occasionally the detergent drawer should be cleaned.
o Pull the detergent drawer out
as far as it will go and then
remove the drawer by pulling
firmly.
o Use warm water and a brush to thoroughly clean
the three compartments of the detergent drawer.
o Clean the area that the detergent drawer slides
into with a brush.
o You should also clean the siphon that sits inside
of the conditioner section of the detergent
drawer. Taking care to make sure that the siphon
is inserted back in the drawer correctly.
ly back
into position.
he washing machine drum
ed inside the drum, then
is possible for the drum to become stained.
n/steel wool or
couring agents to clean the drum of your appliance.
he drum with an appropriate
stainless steel cleaning agent.
o Replace the detergent drawer by placing it back
into the slot. Then push the drawer ful
T
The drum of your washing machine is constructed from stainless steel.
However if there are objects that can rust plac
it
IMPORTANT: Do not use a descaling agent, iro
s
9 Remove any rust stains on t
25
26
oor gasket
door
gasket. This sits inside the opening of the porthole door.
rror code failure system
D
9 You should regularly check to see if any deposits have
formed, or there are any foreign bodies in the rubber
E
If your appliance senses that it is not operating correctly, then an error
ode may appear in the LCD display.
ied by the customer
nd the steps outlined below should be followed.
LD BE DISCONNECTED FROM YOUR MAINS POWER
UPPLY.
lug is in the mains socket correctly.
Check the mains fuse.
pply.
e the water tap that the machine is connected to is turned
on fully.
ain or spin
Check the drain hose is not blocked or kinked.
he door has been shut properly before commencing a
wash cycle.
thes in the drum,
tion.
See the “General troubleshooting” section.
05 – F10- Contact Baumatic Service Department
ine and hold down the Start/Stop button for approximately
5 seconds.
c
The following error codes can possibly be remed
a
BEFORE COMPLETING ANY MAINTENANCE ON THE APPLIANCE,
IT SHOU
S
No display
o Power failure.
o Check that the power p
o
F01- No water coming into the machine
o Check the water pressure of your mains water su
o Clean the mesh filter that sits in the inlet hose.
o Make sur
F02- The machine will not dr
o Clean the drain pump filter.
o
F04- The machine does not start
o Check that t
C03- The machine has sensed an out of balance load
o This may be due to uneven distribution of clo
which may cause an excessive level of vibra
o
F
Once the machine has been plugged back into your mains power
supply, to clear the fault code from the LCD display, you should turn
on the mach
If a fault code reappears after following the
above advice and clearing the fault code. You
should turn the wash program selection knob
to the off position. Disconnect the appliance
from your mains supply. Then arrange for an
engineer to attend the appliance. You should
contact the Baumatic Service Department on
(0118) 933 6911.
27
LL.
IF AN ENGINEER ATTENDS DURING THE
GUARANTEE PERIOD AND FINDS THAT A FAULT
HAS BEEN CAUSED BY AN ITEM ON THE ERROR
CODE LIST, WHICH COULD HAVE BEEN CLEARED BY
THE CUSTOMER. THEN YOU MAY BE LIABLE FOR
THE COST OF THE SERVICE CA
General troubleshooting
Water under the washing machine
o Tighten the drain pump filter.
o Check the drain and inlet hose and make sure that it is fully
tightened.
Washing machine vibrates during the spin cycle
o Check that the transport locking devices have been removed (see
installation instructions).
o Make sure that the washing machine is installed on a flat and level
floor.
o Ensure that all four feet are resting firmly on the floor, by pressing
down on each corner and making sure that the appliance is stable.
o If it is unstable then follow the “Positioning and levelling the
appliance” section.
Poor spin results
o Clean the drain pump (see “Cleaning the drain pump filter” section).
Water in the detergent dispenser
o Although there will be some water residue left in the detergent
drawer after a wash cycle has completed. If the drawer is full of
water then you may need to clean the detergent drawer.
Spinning starts late or the machine does not spin
o The imbalance control system has activated because the laundry
is unevenly distributed in the drum.
o The appliance will redistribute the laundry by reversing the drum
rotation. This may take several attempts before the laundry is
evenly distributed and normal spinning can resume.
o If the laundry is still not evenly distributed after 10 minutes, the
machine will not spin. In the event of this, redistribute the load
manually and select the program again.
Uneven load distribution can be caused by too large a wash
load or too small a wash load. It can also occur if a single item
if washed inside the appliance.
Poor wash results
My garments are looking grey and there are limescale
deposits present in the drum of my washing machine.
o There is not enough detergent being added.
o The incorrect detergent is being used.
o Stains are not being pre-treated.
o The correct wash program or wash temperature was not
selected.
I have followed the advice given above, but my
garments are still coming out with grey stains on them.
o The garments are soiled with oils, ointments or grease
and were washed without enough detergent.
o The wash temperature selected was too low.
o Fabric conditioner has come into contact with the
garments. If this happens try to wash out these stains
as quickly as you can and try to avoid getting
conditioner on the garments in future.
After the final rinse, I can still see foam.
o Modern detergents can result in there still being foam in the final
rinse, this does not mean that the washing is not being rinsed
properly.
28
There is white residue on my garments when I remove
them from the appliance.
o Modern detergents can contain insoluble contents, and white
residue after a wash cycle is not necessarily a sign of the garments
not being rinsed properly.
o You should shake out the garment or brush it off. In future possibly
turn the garment inside out before it is washed. You may wish to
move from a powder detergent and switch to a liquid detergent
instead.
Removing stains
Garments that are covered in stains, grease or are heavily soiled may
need to be pre-washed or soaked before being placed inside of the
washer dryer.
o Soaking helps to remove protein-type stains, like blood, milk or
grass.
o Pre-washing helps to loosen soil before the main wash.
Stain removal rules
o Use warm water for soaking or pre-washing stained laundry. Hot
water can set stains.
o Most stains are easier to remove when they are fresh.
o Before treating any stain try to establish; what kind of stain it is,
how old the stain is, what the fabric type is and whether the
fabric is colourfast (check the care label to find this out).
o Washing and drying can fix some stains.
o When bleach is recommended, use a mild fabric bleach that is
safe for the fabric.
o If you need to use a stain remover, put the stained area face
down on a paper towel or white cloth. Apply the stain remover to
the back of the stain. This forces the stain off the fabric, instead
of through it.
29
Stain removal guide
Stain Removal Method
Alcoholic
beverages
The stain should be first washed with cold water, then
wiped with glycerine and water and rinsed with water
mixed with vinegar.
Shoe polish The stain should be softly scratched without ruining the
material, then rubbed with detergent and rinsed. In case
it is not eliminated, rub with 1 unit of pure alcohol (96
degrees) mixed in 2 units of water and then washed with
lukewarm water.
Tea and
coffee
Stretch the stained area of material on the top of a
container and pour water as hot as the material can
endure on it. If the type of material is suitable, wash it
with lye.
Chocolate
and cocoa
Leave your clothes in cold water and rub with soap or
detergent, wash it in the highest temperature that the
material type can endure. If there is still a stain of oil left,
wipe with oxygenated water (in proportion of 3%).
Tomato
paste
Scrape the dried pieces without ruining the material, then
leave in cold water for about 30 minutes and wash by
rubbing with detergent.
Meat broth/
egg
Eliminate the dried stain residues and wipe with a sponge
or soft cloth wetted in cold water. Rub with detergent and
wash with diluted lye.
Grease and
oil stains
First wipe the residues. Rub the stain with detergent and
then wash with lukewarm soapy water.
Mustard First apply glycerine to the stained area. Rub with
detergent and then wash. If the stain still does not
disappear, wipe with alcohol (on synthetic and coloured
cloth, a mixture of 1 unit alcohol, 2 units water should be
used).
Blood stain Lay your clothes in cold water for 30 minutes. If the stain
still does not disappear, lay in mixture of water and
ammonia (3 table-spoons of ammonia in 4 litres of water)
for 30 minutes.
Cream, ice-
cream and
milk
Lay your clothes in cold water and rub the stained area
with detergent. If the stain has still not disappeared,
apply lye on the fabric of your clothes in proper
proportion. (Do not use lye on coloured clothes).
Mould Mould stains should be cleaned as soon as possible. The
stain should be washed with detergent, and if it does not
disappear, it should be wiped with oxygenated water (in
proportion of 3%).
Ink Hold the stained area under cold water and wait until the
inky water completely runs off. Then rub with water
diluted with lemon juice and detergent. Wait five minutes
and then wash.
Fruit Stretch the stained area of your clothes on the top part of
a container and pour cold water on it. Do not pour hot
water on the stain. Wipe with cold water and apply
glycerine. Wait for 1-2 hours and rinse after wiping with a
few drops of white vinegar.
30
Grass stain Rub the stained part with detergent. If the type of fabric
is suitable for use of lye, wash it with lye. Rub your
woollen clothes with alcohol (for coloured one, a mixture
of 1 unit pure alcohol and 2 units of water).
Oil paint The stain should be eliminated before it dries by applying
thinner on it. Then it should be rubbed with detergent and
washed.
Burnt stain If your fabric is suitable for the use of lye, you can add
lye into your washing water. For woollen fabrics, a cloth
dampened in oxygenated water should be pressed on the
stain and it should be ironed with a dry cloth on it. It
should be washed after rinsing well.
Cleaning the drain pump filter
IMPORTANT: Switch off your washing machine and
disconnect the plug from your mains supply.
You should clean out the filter approximately every twenty
washes. If the drain pump filter is not cleaned regularly, then
your appliance may find it difficult to pump out water
efficiently.
Use a coin to turn the filter cap.
Pull out the filter cap.
Place a container under the drain pump
filter, to collect any excess water that may
come out of the drain pump when it is
removed.
31
Turn the filter a quarter turn anti clockwise, water will
start to come out of the drain pump. Continue to turn the
filter anti clockwise until you reach a half turn, more
water will come out of the drain pump.
When all the water has drained
out of the washing machine,
turn the filter several times anti
clockwise, until it can be
removed completely.
Remove the filter and rinse out
the filter under the tap.
Remove any debris from the
filter.
Remove any debris that is in the area of the appliance that you
removed the drain pump filter from.
Screw the filter clockwise back into position, making sure that it is fully
tightened. You should keep turning until you cannot turn it any further.
Refit the filter cap.
IMPORTANT: Do not perform this operation if the appliance has
stuck on a cycle, until the water inside the machine has cooled
sufficiently. Otherwise the water that comes out of the drain
pump filter may still be hot.
32
Installation
IMPORTANT: THIS INSTALLATION MUST BE
COMPLETED BY A SUITABLY QUALIFIED PERSON.
BAUMATIC ONLY SANCTION THE INSTALLATION
GIVEN IN THIS INSTRUCTION MANUAL. YOU
SHOULD KEEP THE TRANSIT PACKAGING, IN CASE
YOU NEED TO TRANSPORT THE MACHINE IN THE
FUTURE.
ition, whilst the
appliance is being
transported.
9 Using a screwdriver,
unscrew the three plastic
transit bolt covers.
9
Loosen and remove the
three transit bolts.
Unpacking the machine and removing the transit bolts
9 Remove the base, corner
protection pieces and top
cover.
9 Locate the three transit
bolts that secure the drum
in pos
33
34
9
Using a screwdriver, refit
the three plastic transit
removed previously.
be removed before your
ashing machine is used for the first time.
ositioning and levelling the appliance
solid and level floor surface.
MACHINE ON A CARPET.
Loosen the adjustable feet
that are positioned on the
base of the appliance.
Slacken off the lock nut on each of the washing
machine feet using a spanner.
Adjust the feet to level off the washing
machine.
bolt covers that you
IMPORTANT: The transit bolts MUST
w
P
9 Place the washing machine on a
9 DO NOT PLACE THE WASHING
9
9
9
35
9 Once levelled correctly, you should tighten the
lock nut back up on each of the washing
machine feet using a spanner.
MPORTANT: When the washing machine is positioned in the location
ur feet are resting firmly on
e floor, by pressing down on each corner and checking that the
mains water supply
9 The water inlet hose will be inside the drum of your washing
machine, when you re
d inlet valve that is located at
the rear of the washing machine. You
should connect the end with the right
angle connector on it to the back of your
Connect the other end of the inlet hose to your mains
water supply
I
where it will be used. Make sure that all fo
th
appliance stands still.
Connecting to the
ceive the appliance.
9 Connect and fully tighten the inlet hose to
the threade
appliance.
9
36
that connects to your mains water supply. The inlet hose
may leak if this filter is missing. This filter is supplied with the
Tighten the inlet hose to your mains supply fully, but do not over
distort the filter that sits in the end of the inlet
hose.
Test for any leaks.
Water outlet
as this may cause siphoning.
RAINAGE HOSE FROM ITS ORIGINAL
LENGTH.
o Please refer to the building in template for instructions on how to
fit your integrated appliance and connect the furniture door to
the product.
9 IMPORTANT: There should be a filter sitting inside the end of the
inlet hose
appliance, you should contact Baumatic to obtain one, if it is
missing.
9
tighten as this may
9
9 Secure the drain hose, so that it cannot move whilst the washing
machine is in use.
9 Place the end of the drain hose on your drain pipe. Push it a
short way down into your drain pipe.
9 IMPORTANT: Do not insert the drain hose too deeply into the
water pipe,
9 NEVER EXTEND THE D
Fitting the furniture door
Power supply
37
appliance is a built in product, the
electrical socket must still be accessible once the
r of the
BEFORE
,
is the same as that
9 DO NOT REMOVE THE RATING PLATE AS THE
9 The moulded plug that is supplied with the appliance must be
ower leads must only be replaced by a
suitably qualified person. A power lead of a similar type must be
mend that this appliance is
connected to an extension lead.
9 IMPORTANT: As your
appliance is installed.
9 Consult the rating
plate, located on
the inner rim of the
porthole doo
appliance
making the
electrical
connections. Ensure
that the voltage
reaching the plug
on the rating plate.
INFORMATION ON IT IS IMPORTANT.
placed into an earthed and insulated socket.
9 Broken or damaged p
used in replacement.
9 Power lead type – H 0 V V – F 3G 1,5.
9 IMPORTANT: We do not recom
Before first use maintenance
38
commend that you
perform a maintenance wash
that
may have been left on the
drum by the manufacturing
process.
wash program.
A small quantity of detergent should be used during this
maintenance wash.
wash
o When your washing machine
has been correctly installed,
we re
cycle.
o This will check that all
aspects of the installation
are correct; it will also
remove any deposits
o Select a Normal 90°C
o
39
United Kingdom
Baumatic Ltd.,
Baumatic Buildings,
6 Bennet Road,
Reading, Berkshire
RG2 0QX
United Kingdom
Sales Telephone
(0118) 933 6900
Sales Fax
(0118) 931 0035
Customer Care Telephone
3 6911 (0118) 93
Customer Care Fax
(0118) 986 9124
Spares Telephone
(01235) 437244
Advice Line Telephone
(0118) 933
6933
E-mail:
sales@baumatic.co.uk
customercare@bauma
tic.co.uk
uk
o.uk
spares@baumatic.co.
technical@baumatic.c
Website:
www.baumatic.co.uk
epublic of Ireland
ervice Telephone
R
S
-890 812 724
pares Telephone
1
S
91 756 771
zech Republic
ípová 665
erec 4
577 200
s.r.o.
421 255 640 618
ermany
ilienthalstrasse 1
Herford
aumatic Italia S.R.L.
ni N.3
D)
ww.baumatic.it
olland
B.V.
rindzuigerstraat 22
333 MS ALMERE
ederland
136 549 1555
www.baumatic.nl
0
C
Baumatic CR s.r.o.
L
460 01 Lib
Czech Republic
+420 483
www.baumatic.cz
Slovakia
Baumatic Slovakia,
Galvániho 7/D
Slovakia
+
G
Baumatic Gmbh
L
320 52
Deutschland
+49 5221 694 99-0
www.baumatic.de
Italy
B
Via Galva
35011 Campodarsego (P
+3904 9920 2297
w
H
Baumatic Benelux
G
1
N
+3
40
… 31 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Baumatic BWD 12.1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Baumatic BWD 12.1 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info