305966
9
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
21
YOUR ELECTRONIC WASHING MACHINE GB
This washing machine is equipped with all-electronic control, which opens up a host of possibilities for
you. Amongst others, these include: precise determination of load,
Dynamic-Sense Technology
,
imbalance detection and correction system, fast programme changing, accurate programme sequence
indicator, start delay, soaking, safety feature
“intelligent (anti-flood) Water Stop system”
.
The
load determining facility
evaluates the laundry load at the start of the wash cycle and
optimises the washing procedure accordingly. The machine adapts automatically to the prevailing
circumstances: if you are washing a minimum load, the programme carries out only two rinse cycles
during the cotton and synthetics programmes, while keeping the rinse results very good. You save
on water, energy and time as a result.
Thanks to its
Dynamic-Sense Technology
the appliance adapts optimally to the prevailing
circumstances, achieving favourable consumption figures even in the case of small loads. Water
supply temperature and pressure, quantity of water and degree of loading, are the parameters taken
into account. The progamme duration is influenced by these factors. This is checked and updated
at particular stages of the programme. Consequently, the programme duration can vary by up to 60
minutes.
The
imbalance detection and correction system
protects your washing machine if the
imbalance is too great on initiating a spin cycle. This may occur with a badly distributed load or in
the case of single large laundry item. The laundry is re-distributed and the spin speed is not
increased until satisfactory laundry distribution has been achieved.
If you happen to have selected the wrong programme, you can quickly change programme at any
time, without needing to add new detergent. Select the desired programme and start the
appliance. The new program resumes the wash programme at the same stage at which the
preceding one was interrupted.
The
accurate sequence indicator
shows what stage of the programme has been reached by
LED indicators coming on: after starting the programme, the programme sequence indicator
moves from left to right passing through “Wash”, “Rinse”, “Spin”. Once the current stage of the
programme has been completed that LED indicator goes out.
The washing process is subdivided into three phases which corresponds to the three wash LEDs:
1.
Enzyme phase
: at low temperature, organic soiling such as e.g. blood, milk and egg are
dissolved.
2.
Heating-up phase
: the water is heated up to the selected washing temperature.
3.
Washing phase
: the laundry is washed and, if the temperature is raised, whitened.
Using the
“Start Delay”
option (if present) you can select the programme start time from 1 to 19
hours in advance. You can set the programme start time so that the laundry will be completed by a
particular time, thus allowing you to take advantage of favourable lower electricity tariffs at night.
In order to soak particularly heavily soiled colourfast laundry, select the “Coloured” programme and,
once the water has been fed in, press the
“Start/Pause”
button. The programme is interrupted and
you can leave the laundry to
soak
as long as you want.
You can continue the programme by pressing the
“Start/Pause”
button once again.
Depending on the washing machine type, it may be equipped with the anti-flood safety feature
intelligent Water Stop system
”: Even while switched off your washing machine is able to detect
water leakage and brings this to your attention with an audible alarm.
22
WASH
Resistant cotton
Synthetics
Delicates
The figures correspond to the maximum permitted
washing temperatures.
Hand-washed items
Do not wash
Chlorine bleaching possible
Chlorine bleaching not possible
Dry cleanable
Not dry cleanable
DRY
Dry at normal temperature
Dry at a lower temperature
Do not dry in tumble dryer
IRON
Hot iron
Use medium hot iron
Do not use hot iron
Do not iron
LAUNDRY CARE LABELS
23
QUICK REFERENCE GUIDE GB
BEFORE USING THE APPLIANCE FOR THE FIRST TIME:
FOLLOW THE “INSTALLATION INSTRUCTIONS
”.
REMOVE THE TRANSIT BOLTS BEFORE USING THE APPLIANCE.
First wash cycle without laundry:
1.
Turn on the tap.
2.
Close the appliance door.
3.
Pour a small amount of detergent (about 30 ml) into the detergent dispenser .
4.
Select a short program (see programme chart).
5.
The
“Power On”
indication shows that the machine is switched on.
6.
The pilot lamp of the
“Start/Pause”
button flashes.
Press the
“Start/Pause”
button.
This initial cycle serves to eliminate any water remaining after your appliance was tested at
the factory.
NORMAL DAILY USE:
1.
Turn on the tap.
2.
Sort the wash according to fabric type and colour and load the appliance.
3.
Close the door.
4.
Put in detergent and any additives required into the dispenser.
5.
Select the programme, the temperature and any special options required.
6.
The pilot lamp of the
“Start/Pause”
button flashes.
Press the
“Start/Pause”
button.
IMPORTANT:
During the first 15 minutes of the “Cotton”, “Coulored cotton” and “Synthetics”
programmes the door can be opened for adding laundry (“Door Free” indicator).
This is not possible if “Rapid” is selected.
24
GB CONTENTS
YOUR ELECTRONIC WASHING MACHINE
PAGE
21
LAUNDRY CARE LABELS
PAGE
22
APPLIANCE AND ACCESSORIES
PAGE
25
CHILD SAFETY
PAGE
25
PROTECTING THE ENVIRONMENT
PAGE
26
SAFETY INSTRUCTIONS
PAGE
26
TRANSPORT / HANDLING
PAGE
26
PREPARING THE WASH
PAGE
27
DETERGENT AND ADDITIVES
PAGE
28
DYEING AND BLEACHING
PAGE
29
PROGRAMME SELECTION / PROGRAMME START
PAGE
29
START DELAY
PAGE
29
DOOR LOCK / PROGRAMME END
PAGE
30
CHANGING / INTERRUPTING /
CLEARING PROGRAMME
PAGE
30
REMOVING THE FILTER / DRAINING RESIDUAL WATER
PAGE
30
CARE AND MAINTENANCE
PAGE
32
TROUBLESHOOTING GUIDE
PAGE
33
AFTER-SALES SERVICE
PAGE
35
INSTALLATION INSTRUCTIONS
PAGE
35
25
1. Worktop
2. Control panel
3. Detergent dispenser
4. After-Sales Service sticker (on the back side of the door)
5. Door
6. Door handle
- To open the door press the button on the inside of the handle and pull
- Close the door by pushing it firmly (the lock will click into place)
7. Child safety (inside door)
8. Filter (behind cover)
9. Plinth
10. Residual water drain (behind the plinth)
To protect the appliance from improper use, turn the plastic
screw on the interior of the door using a coin or the thick
rounded plastic projection on the coloured insert from the
detergent dispenser.
1. Slot vertical: safety position, i.e. the door will not lock.
2. Slot horizontal: normal position, i.e. the door can be
locked again.
APPLIANCE AND ACCESSORIES
CHILD SAFETY
26
PACKING
The packing material is 100% recyclable
(marked with the recycling symbol ).
Adhere to local regulations when disposing of
packaging material.
The packaging material (plastic bags,
polystyrene parts, etc.) is potentially
dangerous and must be kept out of reach of
children.
PRODUCT
The appliance is made from recyclable
materials and must be scrapped in
accordance with local waste disposal
regulations.
Before scrapping, cut off the power cable so
the appliance cannot be connected to the
mains.
ENVIRONMENTAL TIPS
Do not exceed the detergent dosages
indicated in the Manufacturer’s instructions.
The Eco Flap - a special system in the outlet
will prevent detergent loss from the drum to
avoid detergent loss into the environment.
Remove detergent from compartment if you
intend scrapping your appliance.
MAXIMISE THE LOAD SIZE
Achieve the best use of energy, water,
detergent and time by using the
recommended maximum load size.
DO YOU NEED TO PREWASH?
Use “Prewash” for heavily soiled laundry only!
Save detergent, time, water and between 5 to
15 % energy consumption by not selecting
“Prewash” for slight to normally soiled laundry.
IS A HOT WASH REQUIRED?
Pretreat stains with stain remover or soak
dried in stains in water before washing to
reduce the necessity of a hot wash program.
Save up to 50% energy by using a 60° C
instead of a 90° C wash programme or a
40° C instead of a 60° C wash programme.
BEFORE USING A DRYING
PROGRAMME
Save energy and time by selecting a high spin
speed to reduce the water content in laundry
before using a drying programme (for
machines with adjustable spin speed).
Use the appliance only for domestic washing
and for its intended application.
Ensure the installation of electrical and water
connections have been made in accordance
with the Manufacturer’s instructions and in
observance of local safety regulations (refer to
“Installation Instructions”).
Before cleaning or maintaining the appliance,
switch it off and unplug it.
When the appliance is not in use unplug it and
turn off the tap.
Do not attempt to force the door open.
Do not allow children to play with the
appliance or enter the drum. Do not rest any
weight on the door.
Packing materials can be dangerous for
children: keep all packing materials (plastic
bags, polystyrene, etc.) well out of their reach.
The appliance conforms to European safety
regulations and to Directive n. 93/68/EEC and
standard 93/68/EC.
1.
Unplug the appliance.
2.
Turn off the tap.
3.
Remove the water supply and drain hose.
4.
Eliminate all water from the hoses and from
the appliance (see “Removing the Filter /
Draining Residual Water”).
5.
Fit the transit bolts (obligatory)
(see “Installation Instructions”).
PROTECTING THE ENVIRONMENT
SAFETY INSTRUCTIONS
TRANSPORT / HANDLING
27
1. Sort the laundry according to…
Type of fabric / care label symbol
Cottons, mixed fibres, easy care/synthetics,
wool, handwashed items.
Colour
Separate whites and coloureds. Wash new
coloured items separately.
•Size
Wash items of different sizes in the same load
to improve washing efficiency and distribute
the load more evenly inside the drum.
Fabric delicacy
Wash delicate articles separately: use a
special programme for Pure New Wool ,
curtains and other delicates. Always remove
curtain glides or wash curtains with the glides
inside a cotton bag.
Use the special program for handwash
fabrics.
Wash stockings, belts and other small items or
articles with hooks (e.g. bras) in special cotton
bags for washing machines or in zipped pillow
cases.
2. Empty pockets
Coins, safety pins and similar can damage
your laundry and the appliance drum and tub.
3. Fasteners
Close zips and fasten buttons or hooks; loose
belts or ribbons should be tied together.
STAIN REMOVAL
Blood, milk, egg and other organic substances
are generally removed by the enzyme phase
of the programme.
To remove red wine, coffee, tea, grass and
fruit stains etc. add a stain removing agent in
detergent dispenser compartment .
Particularly stubborn stains should be treated
before the wash.
LOADING THE LAUNDRY
1. Open the door.
2. Unfold the laundry and place it loosely in the
drum.
3. Close the door.
RECOMMENDED LOADS
See separate programme chart.
N.B. Overloading will result in unsatisfactory
washing results and creased laundry.
PREPARING THE WASH
28
CHOOSING THE RIGHT DETERGENT
The type of detergent depends on:
type of fabric (cottons, easy care/synthetics,
delicate items, wool).
Note:
use only specific detergents for wool.
colour;
washing temperature;
degree and type of soiling.
Notes:
Whitish residues on dark fabrics are caused
by insoluble detergents components used in
modern phosphate-free powder detergents.
If you notice this problem, shake or brush the
affected items or use a liquid detergent.
Keep detergents and additives in a dry place
and out of reach of children.
Use only detergents and additives specifically
produced for domestic washing machines.
If you use descaling agents, dyes or bleaches,
make sure they are suitable for washing
machine use. Descaler could contain
components that can attack parts of your
washing machine.
Do not use solvents (turpentine, benzine,
etc.).
Do not machine wash fabrics that have been
treated with solvents or flammable liquids.
DOSAGE
Follow the instructions on the detergent pack in
relation to:
the degree and type of soiling;
the size of the load;
-
full load: follow the detergent
Manufacturer’s instructions;
-
half load: 3/4 the amount used for a full
load;
-
minimum load (about 1 kg): half the
amount used for a full load;
water hardness in your area (ask for
information from your water company): soft
water requires less detergent than hard water.
Notes:
Too much detergent can result in excess foam
formation, which reduces washing efficiency.
If the appliance detects excessive foam it may
prevent spinning.
The laundry will become grey if you use too
little detergent. Too little detergent will also
lead to increased scale deposits on the
heating element and drum.
Adjust the water hardness level pointer in the detergent dispenser in accordance with the hardness of
the water in your area. Move the pointer sideways to the required position.
FILLING THE DETERGENT AND
ADDITIVES
1.
Pull out the detergent dispenser completely,
until the limit.
2.
Add the detergent:
Programme with pre and main wash
Main wash programme without prewash
When using liquid detergent, remove the
coloured insert and fit it in compartment .
The graduate scale on the insert
makes dosing easier.
Fabric softeners (no more “MAX” mark)
Stain remover agents
Water softeners (water hardness 4)
Starch (dissolved in water)
3.
Close the detergent dispenser completely.
DETERGENT AND ADDITIVES
WATER HARDNESS
Water hardness
area
Characteristics
German scale
°dH
French scale
°fH
Clarke scale
°eH
1
2
3
4
soft
average
hard
very hard
0-7
7-14
14-21
over 21
0-12
12-25
25-37
over 37
0-9
9-17
17-26
over 26
29
Notes:
You can use liquid detergent in the “Prewash”
phase for programmes with this option. In this
case use only powder detergents for the main
wash.
If the “Start Delay” option is used, put liquid
detergent into the drum with a detergent ball.
When using concentrated fabric softeners,
add water in the detergent dispenser up to
“MAX” level mark.
To prevent dispensing problems when using
highly concentrated powder and liquid detergents,
use the special detergent ball supplied with the
detergent and place it inside the drum.
Dyeing: Usual products consist of dye colour,
fixing agent and salt. Pour the dye colour, the
fixing agent and then the salt directly into the
empty drum. Fill in the laundry only afterwards.
Use exclusively dyes and bleaches
recommended for washing machines.
Follow the Manufacturer’s instructions.
Plastic and rubber parts of the machine may
be stained by dyes or bleaches.
See also separate programme overview.
1. Set Programme Selector to the desired
programme. The indicator above the “Start/
Pause” button flashes and the programme
duration is shown on the display (if available).
2. Select additional options, if desired, pressing
the corresponding button.
The indicator for the option is lit up.
N.B.An audible tone is sounded if the
combination of programme and additional
option does not make sense. Unsuitable
combinations of additional options are
deselected automatically.
By a further pressing of the button the
additional option can be turned off again.
The Final Spin Speed is related to the
selected programme and is shown by means
of the indicator lamp.
The Final Spin Speed can be altered by
pressing the “Spin” button.
In some programmes the maximum final spin
speed is limited to go easy on your laundry
items. Selection of a higher spin speed is not
possible.
If “0” is selected, the laundry is not spun
following the final rinse cycle. The water is
simply pumped out. Intermediate spinning is
carried out at reduced speed.
3.
Press the “Start/Pause” button to start the
program
.
(If available)
1. Select the program and temperature, any
additional options and the spin speed.
2. Press the “Start Delay” button. The
associated lamp comes on and the indicator
above the “Start/Pause” button flashes.
Either keep the start delay button pressed or
else press it repeatedly until the desired
number of hours is reached. If the maximum
number of hours is reached for the delayed
start, further pressing of the button starts the
counter at zero again.
3. Press the “Start/Pause” button in order to
start the program.
The start delay hours can be corrected even
after the “Start/Pause” button has been
pressed. Again here either keep the “Start
Delay” button pressed or else press it
repeatedly until the desired number of hours is
reached. Once the display has counted down
to “00” the selected programme is started.
Cancelling the start delay: If, in fact, no start
delay was actually desired turn the
programme selector switch and then set it to
the desired position. The remaining time of the
selected programme is displayed and the
indicator above the “Start/Pause” button
flashes. The programme can now be started
immediately by pressing this button.
If the programme is changed after the start
delay, the start delay option is cleared and the
remaining time is displayed. The indicator
above the “Start/Pause” button flashes.
The programme is not started.
Note: With liquid detergent, a dosing aid
placed directly in the drum should be
used if a start delay has been selected.
DETERGENT AND ADDITIVES
DYEING AND BLEACHING
PROGRAMME SELECTION / PROGRAMME START
START DELAY
30
DOOR LOCK
The door locks automatically after the
programme starts until the end of the
programme.
The “Door free” indicator goes out.
Exception
: In the programmes Cotton and
Synthetics and during the prewash for these
programmes, the door can be opened in order to
add further items during the first 15 minutes after
the start of the programme. This is not possible if
“Rapid Wash” is selected.
If the programme selector is moved to the “
position or if the electricity supply is interrupted,
then after approximately two minutes the door is
released.
PROGRAMME END
The programme end is indicated by:
The “Door Free” indicator coming on and the
remaining time indicator (if available)
showing “0:00”,
An audible tone is sounded three times,
The programme
sequence indicators are all
off.
CHANGING PROGRAMME OR OPTIONS
1.
Set programme selector knob to new
programme. Reselect additional options and
spin speed if appropriate. The indicator light
above the
“Start/Pause”
button will blink.
Note:
The options “Start delay” and “Prewash”
cannot be reselected when the
programme is changed.
2.
Press the
“Start/Pause”
button. The new
programme will continue in the same
programme section during which the current
programme was interrupted.
Note:
Do not add more detergent for this
programme.
PROGRAMME INTERRUPTION / PAUSE
To interrupt the running programme for a certain
period and continue it at a later time:
1.
Press the
“Start/Pause”
button.
The indicator flashes.
2.
Following the desired pause press the
“Start/Pause”
button once again.
CANCELLING THE PROGRAMME
If the current programme is to be terminated
prematurely and cancelled, the water must be
pumped out first before the door can be opened:
1.
Set the programme selector to programme
setting
“Drain”
.
The indicator above the
“Start/Pause”
button flashes. The spin indicator shows “0”
and the remaining time indicator (if available)
shows “0:02” minutes.
2.
Press the
“Start/Pause”
button in order to
start the
“Drain”
programme.
WHEN SHOULD I REMOVE THE FILTER?
Check the filter two or three times a year and
clean it if necessary.
Check the filter if the appliance is not draining
properly or if it fails to perform spin cycles.
Remove the filter if the pump is blocked by an
object (buttons, coins, safety pins, etc.).
IMPORTANT:Make sure the water has had
time to cool before draining
the appliance.
DOOR LOCK / PROGRAMME END
CHANGING / INTERRUPTING / CLEARING PROGRAMME
REMOVING THE FILTER / DRAINING RESIDUAL WATER
31
REMOVING THE FILTER
1.
Switch off the appliance (set the programme
selector to and unplug it).
2.
Remove the coloured insert from the
detergent dispenser and use it to open the
filter cover.
3.
Place a bowl beneath the filter.
4.
Turn the filter slowly anti-clockwise until the
grip is vertical; do not extract filter as yet.
5.
Wait until all the water has drained out.
6.
Now unscrew the filter completely and extract
it.
7.
Remove any foreign material from the filter.
8.
Make sure the pump impeller is not
obstructed.
9.
Insert the filter and screw it fully down in a
clockwise direction (until the grip is
horizontal).
10.
Close the cover.
11.
Pour 0.5 l of water into the detergent
dispenser to reactivate the “Eco System”.
12.
Connect the appliance to the electrical outlet.
13.
Select a programme and start it.
WHEN SHOULD I DRAIN RESIDUAL
WATER?
Before transporting (moving) the machine.
If the appliance is installed in a room subject to
sub-zero temperatures. It is best in this case to
drain the machine after every wash.
DRAINING RESIDUAL WATER
The residual water drain hose is accommodated
behind the appliance plinth.
Before draining residual water unplug the
machine.
1.
Remove carefully the plinth using the thin
rounded projection of the coloured insert
from the detergent drawer.
2.
Grip the cap and pull it out. Remove the cap
from the end of the tube.
3.
Allow all the water to flow into a flat bowl, then
refit the cap and stow the drain tube back in its
compartment.
4.
Before using the machine again, pour about 1
litre of water into the detergent dispenser to
reactivate the “Eco System”.
REMOVING THE FILTER / DRAINING RESIDUAL WATER
9

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Bauknecht-wa-7543
  • Ik heb een Bauknecht WA7543, het water loopt niet goed weg, ik moet na iedere wasbeurt het water
    weg laten lopen, ik denk dat er zich zeepresten en/of kalk zich ergens opgehoopt hebben, hoe kan ik
    dat verwijderen? Ik gebruik nu calgon maar dat helpt niet. Gesteld op 26-1-2020 om 13:39

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bauknecht wa 7543 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bauknecht wa 7543 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Bauknecht wa 7543

Bauknecht wa 7543 Gebruiksaanwijzing - Nederlands - 18 pagina's

Bauknecht wa 7543 Gebruiksaanwijzing - Deutsch - 18 pagina's

Bauknecht wa 7543 Gebruiksaanwijzing - Français - 18 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info