806734
1
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
EN
1
Daily Reference Guide
THANK YOU FOR BUYING A BAUKNECHT PRODUCT.
In order to receive a more complete assistance, please
register your appliance on: www.bauknecht.eu/register
FIRST TIME USE
Before using the appliance carefully read
Safety and Installation Instructions. More information about your
product available on website: docs.bauknecht.eu
After installation, please remember to remove all transport protection
parts from the dishwasher.
SETTING MENU
1. Switch on the appliance by pressing the ON-OFF button.
2. Hold the Settings (Half Load ) button for 3 seconds until you hear
a beep.
3. After one second the rst available setting (letter h”) will be displayed.
4. Press button to scroll through the list of available settings (see ta-
ble below), then press START/Pause to view and change the value of
the currently selected setting.
5. Press button to change the value, then press START/Pause to
save the new value.
6. To change another setting, repeat points 2 and 5.
7. Press ON-OFF or wait 30 seconds to exit the menu.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
The salt reservoir is located in the lower part of the dishwasher (under the
lower rack on the left side).
It is mandatory that the salt reservoir never be empty.
It is important to set the water hardness.
Salt must be lled when the SALT REFILL indicator light on the con-
trol panel is lit.1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Position the funnel (see gure) and ll the salt reservoir
right up to its edge (approximately 0,5 kg); it is not un-
usual for a little water to leak out.
3. Only the rst time you do this: ll the salt reservoir
with water.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly so that no detergent can get into
the container during the wash program (this could damage the water
softener beyond repair).
Run a program every time as soon as you completed relling the salt
reservoir to avoid corrosion.
Setting the water hardness
To allow the water softener to work in a perfect way, it is essential that the water
hardness setting is based on the actual water hardness in your house. This infor-
mation can be obtained from your local water supplier. The factory setting is 3”.
See „WATER HARDNESS TABLE”.
To change, follow instructions in section “SETTING MENU”.
Only use salt that has been specically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indicator
light switches o.
If the salt container is not lled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Use of salt is recommended with any type of dishwasher detergent.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently pre-
venting scale buildup on the heater, contributing also to better cleaning
eciency. This system regenerates itself with salt, therefore it is re-
quired to rell the salt container when empty. The frequency of regen-
eration depends on the water hardness level setting - regeneration takes
place once per 4-6 Eco cycles with the water hardness level set to 3. The
regeneration process occurs at the beginning of the cycle with additional
fresh water.
Single regeneration consumes: ~3L of water;
Takes up to 5 additional minutes for the cycle;
Consumes below 0.005kWh of energy.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser A should be
lled when the RINSE AID REFILL indicator light in the control panel is lit.
1. Open the dispenser B by
pressing and pulling up the
tab on the lid.
2. Pour in the rinse aid (max.110
ml), making sure it does not
overow from the dispenser.
If this happens, clean the spill
immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
Adjusting the dosage of rinse aid
If you are not completely satised with the drying results, you can adjust
the quantity of rinse aid used.
To change, follow instructions in the section “SETTING MENU”.
If the rinse aid level is set to ZERO, no rinse aid will be supplied. The LOW
RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of 6 levels can be set according to the dishwasher model.
If you see bluish streaks on the dishes, set a low number (0-3).
If there are drops of water or limescale marks on the dishes, set
a mid-range number (4-5).
A
B
LETTER SETTING VALUES
(Default - in bold)
Water Hardness Level
(see “SETTING THE WATER HARDNESS”
and “WATER HARDNESS TABLE”) 1 | 2 | 3 | 4 | 5
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF RINSE AID”) 0 | 1 | 2 | 3 | 4 | 5
ActiveDry (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O 1 | 0
Sound
“1” = On, “0” = O 1 | 0
Factory Settings
Press START/Pause to restore to the factory
default all the values of the settings included in
the settings menu.
-
CONTROL PANEL
12 3 4 5678910 11 12 13 14 15 16 17 18 19 20 21 22
1. ON-OFF/Reset button with indicator light
2. Eco program button with indicator light
3. Auto Intensive program button with indicator light
4. Auto Mixed program button with indicator light
5. Auto Fast program button with indicator light
6. Rapid program button with indicator light
7. Crystals program button with indicator light
8. Prewash program button with indicator light
9. Salt reservoir empty indicator light
10. Rinse Aid reservoir empty indicator light
11. Display
12. Program number and remaining time indicator
13. Closed water tap indicator light
14. DESCALE indicator light
15. Power Clean® option button with indicator light
16. Half Load option button with indicator light/ Settings - 3 sec. press
17. Extra Dry option button with indicator light
18. Silent option button with indicator light/ Key lock - 3 sec. press
19. Sani Rinse option button with indicator light
20. Self-Clean program button with indicator light
21. Delay option button with indicator light
22. START/Pause button with indicator light
Water Hardness Table
Level °dH
German degrees
°fH
French degrees
°Clark
English degrees
1 (soft) 0 - 6 0 - 10 0 - 7
2 (medium) 7 - 11 11 - 20 8 - 14
3 (average) 12 - 16 21 - 29 15 - 20
4 (hard) 17 - 34 30 - 60 21 - 42
5 (very hard) 35 - 50 61 - 90 43 - 62
2
EN
1. CHECK WATER CONNECTION
Check that the dishwasher is connected to the water supply and that
the tap is open.
2. SWITCH ON THE DISHWASHER
Press the ON/OFF button.
3. LOAD THE RACKS (see LOADING THE RACKS).
4. FILL THE DETERGENT DISPENSER
5. CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE
Select the most appropriate program in accordance with the type
ofcrockery and its soiling level (see PROGRAMS DESCRIPTION) by press-
ing the selected PROGRAM button.
Select the desired options (see OPTIONS AND FUNCTIONS). Not all
options are compatible with all programs.
6. START
Start the wash cycle by closing the door and pressing START/Pause but-
ton (led is lit). When the program starts you hear a single beep.
7. END OF WASH CYCLE
The end of the wash cycle is indicated by sound and the display
showsEND. Switch o the appliance by pressing the ON/OFF button
and opening the door.
Wait for a few minutes before removing the crockery - to avoid burns.
Unload the racks, beginning with the lower one.
MODIFYING A RUNNING PROGRAM
If a wrong program was selected, it is possible to change it, provided that it has
only just begun. RESET the machine: press and hold the ON/OFF button for
more than 3. sec., and the machine will switch o. The dashboard will show
“0:01”. Wait until drain cycle ends (around 1 minute). Switch the machine back
on using the ON/OFF button and select the new wash cycle and any desired
options. Start the cycle by pressing the START/Pause button.
ADDING EXTRA CROCKERY
Without switching o the machine, open the door rst slightly to avoid water
splashing out (START/Pause led starts blinking) (Caution!: Hot steam!)
and place the crockery inside the dishwasher. Close the door and press the
START/Pause button, the cycle will resume from the point at which it was
interrupted.
ACCIDENTAL INTERRUPTIONS
If the door is opened during the wash cycle, or if there is a power cut, the
cycle stops. Close the door and ONLY IF YOU PRESS the START/Pause but-
ton the cycle will resume from the point at which it was interrupted.
TIPS
Before loading the baskets, remove all food residues from the crockery
and
empty the glasses. You do not need to rinse beforehand under running
water.
Arrange the crockery so that it is held in place rmly and does not tip over;
and arrange the containers with the openings facing downwards and the
concave/convex parts placed obliquely, thus allowing the water to reach
every surface and ow freely.
Warning: lids, handles, trays and frying pans should not prevent the spray-
er arms from rotating.
Place any small items in the cutlery basket.
Very soiled dishes and pans should be placed in the lower basket because
in this sector the water sprays are stronger and allow a higher washing per-
formance.
After loading the appliance, make sure that the sprayer arms can rotate
freely.
UNSUITABLE CROCKERY
Wooden crockery and cutlery.
Delicately decorated glasses, artistic handicrafts and antique crockery.
Their decorations are not resistant.
Parts in synthetic material which do not withstand high temperatures.
Copper and tin crockery.
Crockery soiled with ash, wax, lubricating grease or ink.
The colours of glass decorations and aluminium/silver pieces can change
and fade during the washing process. Some types of glass (e.g. crystal ob-
jects) can become opaque after a number of wash cycles too.
DAMAGE TO GLASS AND CROCKERY
Only use glasses and porcelain guaranteed by the manufacturer as dish-
washer safe.
Use a delicate detergent suitable for crockery
Collect glasses and cutlery from the dishwasher as soon as the wash cy-
cle is over.
TIPS ON ENERGY SAVING
When the household dishwasher is used according to the manufacturer’s
instructions, washing tableware in a dishwasher usually consumes
less energy and water than hand dishwashing.
In order to maximize dishwasher eciency, it is recommended to in-
itiate the wash cycle once the dishwasher is fully loaded. Loading
the household dishwasher up to the capacity indicated by the manu-
facturer will contribute to energy and water savings. Information on
the correct loading of tableware can be found in the Loading chapter.
In case of partial loading, it is recommended to use a dedicated wash op-
tions if available (Half load/ Zone Wash/ Multizone), lling up only select-
ed racks. Incorrect loading or overloading of the dishwasher may increase
resources usage (such as water, energy and time, as well as increase noise
level), reducing cleaning and drying performance.
Manual pre-rinsing of tableware items leads to increased water and ener-
gy consumption and is not recommended.
HYGIENE
To avoid odour and sediment which can be accumulated in the dishwash-
er please run a high-temperature program at least once a month.
Use a teaspoon of detergent and run it without loading to clean your ap-
pliance.
RESISTANCE TO FROST
If the appliance is placed in surroundings exposed to the risk of frost, it
must be drained completely. Turn o the water tap, remove the inlet and
outlet hoses, and let all the water drain away. Make sure that the water
softener is full of dissolved regeneration salt in the salt container, to
protect the appliance from temperatures of up to -20°C.
If the appliance was stored in frost conditions the appliance must remain at
an ambient temperature of min. 5°C for at least 24 hours before the rst run.
ADVICE AND TIPS
DAILY USE
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device C. Introduce
the detergent into the dry dispenser D only. Place the amount of
detergent for pre-washing directly inside the tub.
1. When measuring out the detergent refer to the
mentioned earlier information to add the proper
quantity. Inside the dispenser D, there are indica-
tions to help the detergent dosing.
2. Remove detergent residues from the edges of the
dispenser and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling
it up until the closing device is secured in place.
D
C
The detergent dispenser automatically opens up at the right time accord-
ing to the program.
Usage of detergent not designed for dishwashers may cause
malfunction or damage to the appliance.
EN
3
Daily Reference Guide
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and pressure of the incoming
water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor calibration. The sensor calibration can increase
program duration by up to 20 min.
PROGRAMS TABLE
Program
Programs description
Drying
phase
ActiveDry
Available
options *)
Duration
of wash
program
(h: min)**)
Water
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
Eco 50°- Program is suitable to clean normally soiled table-
ware, that for this use, it is the most ecient program in terms
of its combined energy and water consumption, and that it is
used to assess compliance with the EU Ecodesign legislation. 4:00 9.5 0.65
Auto Intensive 65° - Automatic
program for heavily soiled dishes and
pans. Senses the level of so-
iling on the dishes and
adjusts the program
accordingly. When the
sensor is detecting the
soil level an animation
appears in the display
and the cycle duration
is updated.
2:25 - 3:10 15.5 - 24.5 1.30 - 1.70
Auto Mixed 55° - Automatic pro-
gram for normally soiled dishes with
dried food residues. 1:20 - 3:00 7.5 - 19.5 0.75 - 1.20
Auto Fast 50° - Automatic program
for normally and lightly soiled
dishes. The everyday cycle that
ensure optimal cleaning and drying
performance in shorter time.
1:00 - 1:50 7.5 - 15.5 0.70 - 1.10
Rapid 45° - Program is recommended for limited amount
of lightly-soiled dishes with no dried food residues. Does not
include the drying phase. - 0:30 - 0:40 10.0 - 12.0 0.55 - 0.65
Glass 45° - Program for delicate items, which are more sensiti-
ve to high temperatures, for example, glasses and cups.
1:40 - 1:50 12.5 - 16.5 0.95 - 1.20
Prewash - Use to refresh crockery planned to be washed
later. No detergent is to be used with this program. - 0:12 4.5 0.10
Self-Clean 65° - Program to be used to perform mainte-
nance of the dishwasher, to be carried out only when the
dishwasher is EMPTY using specic detergents designed for
dishwasher maintenance.
-- 1:15 11.0 1.10
ActiveDry - It is a convection drying system which automatically opens
the door during/after the drying phase to ensure exceptional drying per-
formance every day. The door opens at a temperature that is safe to your
kitchen furniture, thus door will not be opened when the option of SANI
RINSE is on.
As additional steam protection, specially designed protection foil is added
together with the dishwasher. To see how to mount protection foil please
refer to the INSTALLATION GUIDE.
This feature is active by default, but it is possible to deactivate it in
the “SETTING MENU”.
DESCALE - Alarm - Limescale accumulation was detected on internal
components of the appliance. Check if the Water Hardness Setting
is at the correct value and salt is present in the salt container (see FIRST TIME
USE), then use a descaling product (WPro brand is recommended) with
Self-Clean program. After a successful descaling, the icon will stop being
displayed.
If the actions above are not performed, product performance will deteriorate.
DESCALE warning will start blinking and «dES» alarm will appear on the
display. If still no action is taken, the appliance will only allow a certain
number of cycles to be started (indicated during «dES» alarm display)
and then will be BLOCKED to prevent component damage, with only
the Self-Clean program available. Performing a full descaling will unblock
the product. In the case of extremely high amounts of limescale, descaling
may have to be performed twice to be ecient.
POWER CLEAN® - Thanks to the additional power jets this option
provides a more intensive and powerful wash in the lower rack, in the
specific area. This option is recommended for washing pots and casseroles
(please refer to the Power Clean® in loading section).
EXTRA DRY - The higher temperature during the final rinse and the
extended drying phase allows for improved drying. The EXTRA DRY
option results in the lengthening of the wash cycle.
DELAY - The start of the program may be delayed for a period of time
between 0:30 and 24 hours.
1. Select the program and any desired options. Press the DELAY button
(repeatedly) to delay the start of the program. Adjustable from 0:30 to 24
hours. Once the 24 hours setting is reached, press the DELAY another time
to deactivate the DELAY function.
2. Close the door and press the START/Pause button. The timer will begin
counting down.
3. Once this time has elapsed, the indicator light switches o and the program
begins automatically.
The DELAY function cannot be set once a program has been started.
WATER TAP CLOSED - Alarm - Flashes, when there is no inlet water or
water tap is closed.
HALF LOAD - If there are not many dishes to be washed, HALF LOAD
is used to save water, electricity or time, depending on the selected program.
Remember to reduce the amount of detergent.
SILENT - Suitable for night-time operation of the appliance. This option
can be used to limit noise emissions during wash phases. It will increase
cycle time depending on base cycle selection.
SANI RINSE - This option can be used to sanitize washed dishes. It will
increase the nal rinse temperature and add an antibacterial wash to
the selected program. Ideal to clean crockery and feeding bottles. The
dishwasher door must be kept shut for the entire duration of the program
in order to guarantee a reduction of germs. WARNING: the crockery and
plates could be extremely hot at the end of the cycle.
SENSING - When the sensor is detecting the soil level an
animation appears in the display (around 20 min.) and the cycle
duration is updated. SENSING is for the level of soiling on the
dishes and is present for all cycles (excepting Eco) adjusting the program
accordingly.
KEYLOCK - A long press (for 3 seconds) of SILENT button, will activate
the KEYLOCK function. The KEYLOCK function will block the control panel
except for the ON/OFF button. To deactivate the KEYLOCK, long press again.
OPTIONS AND FUNCTIONS
OPTIONS can be selected/ deselected, after choosing the program, directly by pressing the corresponding button (if available - the indicator lights up)
(see CONTROL PANEL). If an option is not compatible with the selected program (see PROGRAMS TABLE), the corresponding LED ashes rapidly 3 times and
beeps will sound. The option will not be enabled. An option can change time or water or energy consumption for the program.
4
EN
LOADING THE RACKS
CLEANING THE FILTER ASSEMBLY
Regularly clean the lter assembly so that the lters do not clog and that
the waste water ows away correctly.
Using the dishwasher with clogged lters or foreign objects inside the l-
tration system or spray arms may cause unit malfunction resulting in loss of
performance, noisy work or higher resources usage.
The lter assembly consists of three lters which remove food residues
from the washing water and then recirculate the water.
The dishwasher must not be used without lters or if the lter is loose.
At least once per month or after every 30 cycles, check the lter assembly
and if necessary clean it thoroughly under running water, using a non-me-
tallic brush and following the instructions below:
1. Turn the cylindrical lter A in an anti-clockwise direction and pull it out
(Fig 1). It is important when reinstalling the lter that the two trian-
gles shown on the zoom meet.
2. Remove the cup lter B by exerting a slight pressure on the side aps
(Fig 2).
3. Slide out the stainless-steel plate lter C (Fig 3).
4. In case you nd foreign objects (such as broken glass, porcelain, bones,
fruit seeds etc.) please remove them carefully.
5. Inspect the trap and remove any food residues. NEVER REMOVE the
wash-cycle pump protection (shown by an arrow) (Fig 4).
After cleaning the lters, replace the lter assembly and x it in position
correctly; this is essential for maintaining the ecient operation of the dish-
washer.
CAPACITY: 15 standard place-settings
CARE AND MAINTENANCE
2
1
4
3
A
A
B
C
CUTLERY RACK
The third rack was designed to house the cut-
lery.
Arrange the cutlery as shown in the gure.
A separate arrangement of the cutlery makes col-
lection easier after washing and improves wash-
ing and drying performance.
Knives and other utensils with sharp edges
must be positioned with the blades facing
downwards.
The cutlery rack is equipped with two sliding
side trays to make the most of the height of the
space below and enable the loading of high
items into the upper rack.
UPPER RACK
Load delicate and light dishes: glasses, cups,
saucers, low salad bowls.
The upper rack has tip-up supports which can
be used in a vertical position when arranging
tea/ dessert saucers or in a lower position to
load bowls and food containers.
(loading example for the upper rack)
Adjusting the height of the upper rack
The height of the upper rack can be adjusted: a high position to place bulky
crockery in the lower basket and low position to make the most of the tip-up
supports by creating more space upwards and avoiding collision with the
items loaded into the lower rack.
The upper rack is equipped with an Upper Rack height
adjuster (see gure), without pressing the levers, lift it
up by simply holding the rack sides, as soon as the rack is
stable in its upper position. To restore to the lower posi-
tion, press the levers A at the sides of the rack and move
the basket downwards.
We strongly recommend that you do not adjust the
height of the rack when it is loaded.
NEVER raise or lower the basket on one side only.
Foldable aps with adjustable position
The side foldable aps can be folded or unfolded
to optimize the arrangement of crockery inside
the rack. Wine glasses can be placed safely in
the foldable aps by inserting the stem of each
glass into the corresponding slots.
Depending on the model:
to unfold the ap there is needed to slide it up
and rotate or release it from the snaps and pull
it down.
to fold the ap there is needed to rotate it and
slide ap down or pull it up and attach ap to
the snaps.
LOWER RACK
For pots, lids, plates, salad bowls, cutlery etc. Large plates and lids should
ideally be placed at the sides to avoid interferences with the spray arm.
The lower rack has tip-up supports which can be used in a vertical position
when arranging plates or in a horizontal position (lower) to load pans and
salad bowls easily.
(loading example for the lower rack)
POWER CLEAN®
Power Clean® uses the special water jets in
the rear of the cavity to wash more intensive-
ly the highly dirty items. The lower rack has
a Space Zone, special pull-out support in the
rear of the rack that can be used to support
frying pans or baking pans in an upright po-
sition, thus taking up less space.
Placing the pots/casseroles faced to the
Power Clean® component please activate
the POWER CLEAN® on the panel.
How to use the Power Clean®:
1. Adjust the Power Clean® area G folding
down the rear plate holders to load pots.
2. Load pots and casseroles inclined verti-
cally in the Power Clean® area. Pots have
to be inclined towards the powerful water
jets.
EN
5
Daily Reference Guide
CLEANING THE SPRAY ARMS On occasions, food residue
may become encrusted onto
the spray arms and block the
holes used to spray the wa-
ter. It is therefore recommen-
ded that you check the arms
from time to time and clean
them with a small non-me-
tallic brush.
To remove the upper spray
you must remove it together
with the manifold.
The lower spray arm may be removed
by pulling it upwards and rotating it
anti-clockwise. Mounting back the
spray arm is by pulling it down and
rotating it clockwise.
The top spray arm may be removed
by pressing it up and then rotating it
anti-clockwise. Mounting back the
spray arm is by pulling it upwards and
rotating it clockwise.
TROUBLESHOOTING
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service whose contact details can be found in the warranty booklet.
Spare parts will be available for a period of either up to 7 or up to 10 years, according to the specic Regulation requirements.
PROBLEMS POSSIBLE CAUSES SOLUTIONS
The salt
indicator is lit Salt reservoir is almost empty. Rell the reservoir with salt (for more information - see FILLING THE SALT RESERVOIR).
Check the water hardness setting if necessary - see WATER HARDNESS TABLE.
The salt
indicator is
blinking Salt reservoir is empty. Rell the reservoir with salt as soon as possible. Using the appliance without salt may cause
damage to its internal components.
The rinse aid
indicator is lit
or blinking
Rinse aid dispenser is empty. (After rell the rinse
aid indicator may remain lit for a short time). Rell the dispenser with a rinse aid (for more information - see FILLING THE RINSE AID DISPEN-
SER).
Descale indicator
is lit or blinking;
«dES»
alarm is
displayed.
Limescale is accumulating on internal components of
the appliance.
Descale the appliance immediately using the Self Clean program and a commercially available
descaling product (see OPTIONS AND FUNCTIONS). Rell the reservoir with salt. Check the water
hardness setting. If the appliance is not descaled, it will stop functioning.
The dishwasher
won’t start or does
not respond to
commands.
The appliance has not been plugged in properly. Insert the plug into the socket.
Power outage. For safety reasons, the dishwasher will not restart automatically when power returns.
Close the door and press START/Pause button.
The dishwasher door is not closed.
ActiveDry pin is not pulled in. Vigorously push the door until you hear the click”.
A cycle is interrupted by the door opening for
more than 4 seconds. Close the door within 4 seconds and press START/Pause button.
The control panel does not respond or F6 E1 is
displayed.
Switch o the appliance by pressing the ON-OFF/Reset button, switch it back on after approxima-
tely one minute and restart the program. If the problem persists, unplug the appliance for
1 minute, then plug it back in.
The dishwasher
won’t drain.
Display shows:
F7 E3 or F9 E1
The lter is clogged with food residues or limescale. Clean the lter and descale the appliance (see CLEANING THE FILTER ASSEMBLY and DESCALE
INSTRUCTION).
The drain hose is kinked. Check the drain hose (see INSTALLATION INSTRUCTIONS).
The sink drain pipe is blocked. Clean the sink drain pipe.
The dishwasher
makes excessive
noise.
Dishes are rattling against each other. Position the crockery correctly (see LOADING THE RACKS).
An excessive amount of foam is present.
The detergent has not been measured out correctly or it is not suitable for use in dishwashers
(see FILLING THE DETERGENT DISPENSER). Restart the current cycle by switching OFF the dishwa-
sher, then switch it on again, select a new program, close the door and press START/Pause
button. Please do not add any detergent.
Crockery has not been arranged properly. Arrange the crockery correctly (see LOADING THE RACKS).
The lter is clogged with food residues or limescale. Clean the lter assembly (see CARE AND MAINTENANCE).
The dishes are not
clean.
Crockery has not been arranged properly. Arrange the crockery correctly (see LOADING THE RACKS).
Spray arms cannot rotate freely, being hindered by
the dishes. Arrange the crockery correctly (see LOADING THE RACKS). Check that the upper rack is in the
correct position and adjust (lift up) if necessary.
The wash cycle is too gentle. Select an appropriate wash cycle (see PROGRAMS TABLE).
An excessive amount of foam is present.
The detergent has not been measured out correctly or it is not suitable for use in dishwashers
(see FILLING THE DETERGENT DISPENSER).
The cap on the rinse aid compartment has not
been closed correctly. Make sure the cap of the rinse aid dispenser is closed.
The lter is clogged with food residues or limescale. Clean the lter and descale the appliance (see CLEANING THE FILTER ASSEMBLY).
The salt reservoir is empty. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
6
EN
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
Using QR code and visiting our website: docs.bauknecht.eu
Visiting our website: parts-selfservice.whirlpool.com
Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting
our After-sales Service, please state the codes provided on your product’s identication plate.
The model information can be retrieved using the QR-Code reported in the energy label. The label also includes
the model identier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu
IEC 436
:
PROBLEMS POSSIBLE CAUSES SOLUTIONS
The dishwasher does
not ll the water.
The display shows:
H2O and is
lit; acoustic alarm
sounds.
No water in the water supply or the tap is closed. Make sure there is water in the water supply and the water tap is open.
The water inlet hose is kinked. Check the inlet hose (see INSTALLATION). Close the door and press START/Pause button.
The screen in the water inlet hose is clogged; it is
necessary to clean it. Check and clean the screen in the water inlet hose. Close the door and press START/Pause
button.
The dishwasher
nishes the cycle
prematurely.
The display shows:
F8 E3
The lter is clogged with food residues or lime-
scale. Clean the lter and descale the appliance (see CLEANING THE FILTER ASSEMBLY and DESCALE
INSTRUCTION).
Drain hose positioned too low or siphoning into
the home sewage system.
Check if the end of the drain hose is placed at the correct height (see INSTALLATION). Check for
siphoning into the home sewage system, and install a siphon breaker/air admittance valve if
necessary.
An excessive amount of foam is present. The detergent has not been measured out correctly or it is not suitable for use in dishwashers
(see FILLING THE DETERGENT DISPENSER).
Air in the water supply. Check water supply for leaks or other issues letting air inside.
The dishes are not
dried well.
Rinse aid is not present or the dosage is too low. Make sure the rinse aid dispenser is lled (see FILLING THE RINSE AID DISPENSER). Multifunctional
tablets only will not provide as good drying eects as the actual use of liquid rinse aid.
The dishes have been unloaded after the door
was opened automatically but before the actual
cycle end.
Make sure the cycle has ended before starting to unload the dishes (see DAILY USE). For even
better drying results, it is recommended to let the dishes sit inside the dishwasher with the door
open for additional 15 minutes after the cycle ends.
The dishes are sitting too at. If you notice puddles of water inside cavities of cups, mugs or bowls, try loading the dishes
(especially in the upper rack) providing more inclination to let larger amounts of water drip
down before drying starts.
The selected cycle does not have the drying
phase.
Please check in the PROGRAMS TABLE if the selected program is equipped in the drying phase. A
cycle without the drying phase may not deliver desired drying eciency, so it is recommended
to change cycle selection for the one that has the drying phase.
The dishes are made of non-stick or plastic. Some water drops remaining on this type of material are normal.
Dishes and glasses
have blue streaks
or bluish tinges. Rinse aid dosage is excessive. Adjust the dosage to a lower setting.
Dishes and glasses
are covered with li-
mescale or a whitish
lm.
The salt reservoir is empty. Rell the reservoir with salt as soon as possible. Using the appliance without salt may cause
damage to its internal components.
The water hardness setting is too low.
Increase the setting (see WATER HARDNESS TABLE).
The cap of the salt reservoir is not properly closed. Check and close the salt reservoir cap.
The rinse aid reservoir is empty or the rinse aid
dosage is insucient. Rell the dispenser with rinse aid and check the dosage setting (for more information - see
FILLING THE RINSE AID DISPENSER).
The dishwasher
shows F8 E5 Valve is blocked or faulty. Close the water tap, if possible. Do not switch o the power supply. Call the service.
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bauknecht B7F HS51 X bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bauknecht B7F HS51 X in de taal/talen: Engels als bijlage per email.

De handleiding is 9.03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Bauknecht B7F HS51 X

Bauknecht B7F HS51 X Gebruiksaanwijzing - Deutsch - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info