589472
14
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
English
14
.
Warning: Do NOT leave the charger
plugged in for longer than 5 hours. The
battery will be fully charged within one
hour. Leaving the charger plugged in for
longer than 5 hours may damage the
battery.
Inserting a Bit into the Bit Connector:
Push forward metal collar and insert any ¼ in.
hex shank accessory. Release the collar to
lock the accessory in the bit connector (7).
Removing a Bit from the Bit Connector:
Push forward the metal collar to release the
accessory from the bit connector.
LED Worklight
This driver has a LED worklight (1) built into the
head of the tool. Turn the LED bulb towards the
direction of the connector to turn on. The light
will remain on while it is in the same direction
as the connector. To turn off the light, turn the
LED bulb towards the battery compartment (2).
Replacing the Worklight Battery
Remove the battery cover (2) and replace the
battery with a new one (CR927). Please
observe correct polarity, the positive pole (+) of
the battery must point to the battery compart-
ment cover.
Forward/Reverse Switch
The forward/reverse switch (3) is conveniently
mounted below the trigger switch (5). To make
the driver rotate clockwise for driving screws,
push the forward/reverse switch to the left. To
make the driver rotate counter clockwise for
removing screws, push the forward/reverse
switch to the right.
Notes:
a. Never change the position of the forward/
reverse switch while the driver is turning.
b. The trigger switch will NOT function
with the forward/reverse switch in the
middle/neutral position.
Variable Speed Trigger Switch
The cordless driver is equipped with a varia-
ble-speed trigger switch.
1. To start the driver, gently squeeze the
trigger switch (5).
NOTE: The driver will turn at its slowest speed
when the trigger switch is squeezed lightly. The
driver will turn at its fastest speed when the
trigger switch is squeezed rmly.
2. To stop the cordless driver, release the
trigger switch.
NOTE: Operating the driver at a slow speed for
an extended period of time may cause the
driver motor or the battery to overheat. If the
driver gets hot, stop operating it and allow it to
cool for at least 15 minutes.
Multi-Position Driver Head
The cordless driver has a multi-position head.
This allows the connector to move in any direc-
tion required.
1. To rotate the head 360º, push the switch
(6) towards the connector and freely rotate
the head.
2. To change the angle of the driver head
push button (13) and rotate the angle of
the head.
3. To change the angle of the connector
push button (12) and rotate the head.
MAINTENANCE AND CLEANING
Maintenance
There are no inner parts of the tool which need
maintenance.
Cleaning
Keep safety devices, ventilation openings
and the motor housing as free as possible
from dirt and dust. Rub the electric power
tool with a clean cloth or blow over it with
low pressure compressed air.
We recommend that you clean your elec-
tric power tool immediately after each use.
Clean the electric power tool regularly with
a damp cloth and somewhat soft soap. Do
not use any cleaning or solvent materials;
these can attack the device’s plastic com-
ponents. Make sure that no water can get
inside the electric power tool.
7062267_FlipOut_Ma_#1503-12.indb 14 26-03-15 09:11
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Batavia BT-TS001 FLIPOUT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Batavia BT-TS001 FLIPOUT in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 4,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info