759825
9
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
9
English
.
To turn off the appliance:
Press the on / off switch (1) again. The unit
is now switched off.
To install the nozzle:
The nozzles can easily be pushed over the hot
air nozzle. Never touch the nozzles during or
immediately after use of the device. The
nozzles are very hot.
Rotating handle:
The device has two handle positions (see Fig.
D) Position 1 is suitable for killing weeds and
igniting the BBQ. In position 2, the device can
be used as a hot air gun.
To change the handle position:
Press the release button (8)
Turn the handle to the desired position
Make sure that the release button has
been locked again.
OPTION 1: WEED KILLER
Assembly of the telescopic extension
handle:
Attach the extension handle to the device.
Make sure that the extension handle rmly
clicks into position.The telescopic extension
handle can be adjusted easily to the required
length. Turn knob A, reposition the handle to
the desired length and then turn knob A
securely.If using the device as a weed killer you
must use the extension handle.Hold the weed
killer rmly by holding the end of the extension
handle.
Use:
Ensure the extension handle is rmly xed
onto the device and that the device is
turned off.
Turn the device to position 1 (see Fig. D)
Install the nozzle (11) to destroy weeds.
Insert the plug into the socket
Check to ensure the nozzle is not blocked
before turning the device on.
Set the temperature to setting II or III.
Allow the device about 45 seconds to
warm up.
To eliminate weeds, hold the nozzle over
the weeds for about 5 seconds. During
these 5 seconds the cell structure of the
weed is destroyed. As a result, the weed
dies within a few days.
It is not necessary to completely burn the
weeds, 5 seconds is more than sufcient.
For an efcient treatment the nozzle
should be held around 0 to 5 cm above
the weeds
The effects are not visible immediately but
will take a while before they can be seen. It
is more of a long-term effect.
OPTION 2: SPECIFIC WEED KILLER
Ensure the extension handle is rmly xed
onto the device and that the device is
turned off.
Turn the device to position 1 (see Fig. D)
Install the Heat-pin (15) to heat-treat the
weed.
Insert the plug into the socket.
Set the temperature switch in position “III”.
Allow the device about 60 seconds to
warm up.
Position the heat-pin in the middle of the
weed, and push the pin into the weed, up
to the mark, and retract the heat-pin from
the soil after about 2 seconds.
The effect of the treatment will not be
immediately obvious as it can take several
days before it is visible, but it will have a
long-term effect.
Use the heat-pin only on the lawn and
loose soil. Do not use on rocky soil as the
heat-pin could break off.
On some occasions, a small brown spot of
burned grass can occur, but this will
recover very soon.
OPTION 3: PAINT REMOVAL
The paint removal is always done without the
use of the extension handle. Remove the
extension handle by pressing and releasing
button (7) and pulling the extension handle
from the device.
7063002-Maxxheat-II-Ma-1712-21.indb 9 04-01-18 10:56
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Batavia BT-HG002 7063389 UK bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Batavia BT-HG002 7063389 UK in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 2,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info