589478
15
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
charged after only 60 seconds. This way it is
ready for use all the time.
Regardless of the charging condition, the
ash cell screwdriver can be charged at any
time without damaging the cells.
Charge the screwdriver before rst use.
Note:
The charger BT-FCC001 can only be used for
the driver BT-CSD002.
1. Connect the power cord (5) of the charger
(6) with a wall socket. The rst LED of the
charging LEDs (3) lights up.
2. Put the lower end of the handle of the
screwdriver, as pictured on the overview
photo, as far as it will go into the charger, by
inserting the charging terminals into the
corresponding openings of the charger.
3. Depending on the charging state, the
corresponding charging LEDs light up and
ash. The ash cell is fully charged when all
LEDs shine permanently. The screwdriver is
ready for use.
Note:
When inserting the screwdriver into the
charger, make sure it easily can be placed. Do
not use force.
INSERTING/REPLACING THE SCREW BIT
Before changing the screw bit, set the
rotating direction button (7) into the middle
position to avoid unintentional start-up.
Only replace the screw bit when the
screwdriver is switched off.
Pull out the screw bit from the bit holder (1)
and replace it with the desired one. A
magnet inside the bit holder holds the
screw bit in its place.
USING THE TWIST-GRIP
The ash cell screwdriver is equipped with an
adjustable twist-grip which can be setup as a
straight grip or as a pistol grip. Press the
unlocking button (8) at the top of the screw-
driver and twist the grip to the desired position.
Straight Grip Pistol Grip
SWITCHING ON AND OFF/SCREWING
1. Press the ON/OFF trigger (2) to switch
on the ash cell screwdriver. Release the
trigger to switch off the screwdriver.
2. Use the rotating direction button (7) to
reverse the rotating direction. In the
middle position the ON/OFF trigger is
locked. Set the switch to this position
when putting down the machine to avoid
an accidental start-up.
3. Before using the machine, check whether
the screw bit is inserted correctly. Avoid
overtightening as this may damage the
screw head or the threads. Press the
screw bit against the screw with a
constant pressure and drive in the screw.
15
EN
7061166 Ma # 1201-09.indd 15 09-01-12 12:29
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Batavia BT-CSD002 DUO bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Batavia BT-CSD002 DUO in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 4,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info