759583
31
Verklein
Vergroot
Pagina terug
1/66
Pagina verder
29
English
.
tool and inspect the workpiece. Move
forward at a slower speed.
Line cuts
You can follow a drawn line with the help of the
indicator marks (a), at the front and rear of the
safety guard. For precise work, the relationship
between the saw cut and a marked indicator
line must be established using a test piece.
The ideal positioning of the saw cuts must then
be achieved by adjusting the indicator line to
the target line.
Working with large workpieces
When working with large workpieces or cutting
straight edges:
Use fastening clamps to tighten a board or
border onto the workpiece as an auxiliary
stop.
Guide the left-hand side of the base plate
along the auxiliary stop.
Plunge cuts (Figure 1)
Note: Some very hard materials are not suita-
ble for plunge cuts.
1. Put the base plate on the workpiece.
Make sure that the rear lateral depth mark-
ing is at the height of the beginning of the
cut.
2. Switch on the electric power tool and
allow a couple of seconds to pass until the
tool insert reaches its full speed. Then
plunge the tool insert, slowly but with
some pressure.
3. Push the electric power tool forwards
through the workpiece.
4. When you reach the end of the cut, switch
off the electric power tool and pull it out of
the workpiece.
Cutting tiles
Adhesive tape or insulation tape on the work-
piece makes the work easier and helps to
prevent it from getting scratched.
After use:
1. Switch of the tool
2. Remove the plug from the socket
3. Let the tool cool down
4. Remove all accessories such as
sawblades
CLEANING AND MAINTENANCE
Warning! Pull out the power plug
before any cleaning work.
Cleaning
Keep safety devices, ventilation openings
and the motor housing as free as possible
from dirt and dust. Rub the electric power
tool with a clean cloth or blow over it with
low pressure compressed air.
We recommend that you clean your elec-
tric power tool immediately after each use.
Clean the electric power tool regularly with
a damp cloth and somewhat soft soap. Do
not use any cleaning or solvent materials;
these can attack the device’s plastic com-
ponents. Make sure that no water can get
inside the electric power tool.
Unlock and remove the lid if the adapter is
dusty. Replace the lid after cleaning.
Maintenance
Carbon brushes
In the event of excessive sparking, allow a
qualied person to examine the carbon
brushes.
ATTENTION! The carbon brushes
may only be exchanged by a qualied
person.
There are no inner parts of the tool which need
maintenance.
REPAIR AND ORDERING OF SPARE
PARTS
Exchanging the power cable
If the power cable of this electric power tool is
damaged, it must be replaced by the manufac-
turer, its customer services department or a
similarly qualied person to avoid danger.
Spare parts/Accessories
Spare parts can be ordered through the Cus-
tomer Service using the following information:
Type of device
Model of the unit
ID number of the device
Transport
Do not lift the tool by the mains cable
Transport the tool in its original packaging
to avoid transport damage
7062244_MaxxSaw_Ma_#1612-19.indb 29 19-12-16 10:31
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Batavia BT-CS009 - 7062244 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Batavia BT-CS009 - 7062244 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 5,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info