765278
1
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
[Type here] [Type here] [Type here]
Bartec Auto ID Ltd. SW Version: R.5.3 (English) 2019
TAP100/TAP200
Tread Depth and Pressure Tool
User Guide
Enter
Display
Rubber
housing
Up/Down
navigation
Wireless
wall
charger
Pressure hose
connection with
protective cap
Hose
Pin cover
Tread
depth pin
Micro USB
port for
updating
TAP100/200 User Guide R.5.3 2019
2 | Page
FOREWORD
Dear customer,
Thank you for having chosen one of our tools. We are certain that it will give the utmost satisfaction and be
a great help on the job.
Please become fully familiar with the instructions in this user’s manual. It should be kept ready to hand for
consultation whenever required.
The TAP100 and TAP200 tools are designed to measure a tyres tread depth and pressure in a simple and fast
process and displays the results on a high resolution colour display, making them easily presentable for the
customer.
These tools are acceptable for use during statutory test conducted in accordance with Motor Vehicle (Tests)
Regulations 1981, as amended.
DVSA (MOT-UK) approval numbers are: TAP100 - EINYA19863-0716026
TAP200 - EINYA19863-0117005
CE COMPLIANCE
Type Designation: TAP100, TAP200
Description/Intended Use: Hand Held Tread Depth and Pressure Reader used to read tyre data and presenting the
results.
Hereby, Bartec declares that the product referenced above is in compliance with the essential requirements of Directive
1999/5/EC, on the approximation of the laws of the member states relating to Directive 1999/5/EC.
TAP100/200 User Guide R.5.3 2019
3 | Page
LIST OF CONTENTS
FOREWORD................................................................................................... 2
LIST OF CONTENTS ...................................................................................... 3
IMPORTANT NOTICES .................................................................................. 4
SAFETY PRECAUTIONS ................................................................................. 4
BEFORE GETTING STARTED ......................................................................... 6
KIT COMPONENTS ....................................................................................... 7
MENU NAVIGATION ..................................................................................... 8
TOOL POSITIONING ...................................................................................... 9
TOOL CONNECTIONS ................................................................................... 9
CHARGING TOOL ....................................................................................... 10
POWER ON/OFF SEQUENCE .................................................................. 11
HOME MENU ............................................................................................. 11
START MEASUREMENTS ............................................................................ 11
VEHICLE AUDIT SCREEN ........................................................................... 12
TREAD DEPTH AND PRESSURE READ ....................................................... 12
SEND DATA ................................................................................................ 13
CLEAR VEHICLE DATA ............................................................................... 14
WHEELS ..................................................................................................... 14
SETUP ......................................................................................................... 14
TOOL INFO ................................................................................................. 15
REGISTERING YOUR TOOL ........................................................................ 16
TPMS DESKTOP ....................................................................................... 18
UPDATING YOUR TOOL VIA TPMS DESKTOP ........................................ 19
TECHNICAL SPECIFICATION ...................................................................... 23
BARTEC PRODUCT RANGE & ACCESSORIES ............................................ 24
TAP100/200 User Guide R.5.3 2019
4 | Page
IMPORTANT NOTICES
SAFETY DEFINITIONS
All Danger, Warning, Important, and Note messages must be followed for your safety. These safety messages
are in the following form
DANGER: Means you may risk possible loss of life.
WARNING: Means you may risk possible bodily harm.
CAUTION: Means you risk damage to the vehicle or the tool.
These safety messages cover situations Bartec is aware of. Bartec cannot know, evaluate and advise you as
to all the possible hazards. You must be certain that any conditions or service procedures encountered do not
jeopardise your personal safety.
COPYRIGHT
No part of this manual may be reproduced, stored in a retrieval system or transmitted, in any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of
Bartec.
DISCLAIMER
All information, illustrations, and specifications contained in this technical instruction manual are based on the
latest information available at the time of publication. The right is reserved to make changes at any time
without obligation to notify any person or organization of such revisions or changes. Further, Bartec shall not
be liable for errors contained with the furnishing, performance or use of this material.
SAFETY PRECAUTIONS
Read carefully the installation, operating and maintenance instructions in the Operator’s manual.
Do not allow unqualified persons to use this equipment. This will prevent injury to persons and damage to the
equipment.
The work place must be dry, sufficiently lit and well ventilated.
Do not forget that breathing carbon monoxide (odourless) can be very dangerous and even fatal.
When working on the vehicle:
Wear suitable clothing and act in such a way as to prevent industrial accidents.
Before starting, check to be certain the gear shift is in neutral (or in PARK (P) if the transmission is
automatic) and put the handbrake on and check to be sure the wheels are completely locked.
Do not smoke or use naked flames when working on a vehicle.
Wear safety glasses to protect your eyes from dirt, dust or metal chips.
TAP100/200 User Guide R.5.3 2019
5 | Page
Disposing of equipment
Do not dispose of this equipment as miscellaneous solid waste but arrange to have collected
separately.
The re-use or correct recycling of electronic equipment (EEE) is important in order to protect the
environment and human health.
In accordance with European Directive WEEE 2002/96/EC, special disposal points are available for
waste electrical and electronic equipment.
Public administrators and producers of electrical and electronic equipment are involved in facilitating
the re-use and recovery of waste electrical and electronic equipment through these collection
activities and use of appropriate planning arrangements.
Unauthorised disposal of waste electrical and electronic equipment is punishable by law with
appropriate penalties.
Disposing of batteries
The TAP100 and the TAP200 contain a Lithium Polymer rechargeable battery which is not accessible
to the user.
Batteries must be recycled or disposed of properly. Do not throw batteries away as part of normal
refuse disposal.
Do no throw batteries on to an open fire
Correct use of the tool
Do not expose the tool to excessive moisture.
Do not use the tool near sources of heat or polluting emissions (stoves, ovens, etc.).
Do not drop the tool.
Do not allow the tool to come into contact with water or other liquids.
Do not open the tool or attempt to perform maintenance or repair operations on any internal parts.
You are advised to keep the packaging and to re-use it if the tool is moved to another site.
When using the tool remember:
Do not subject the tool to magnetic or electric interference.
Reception, maintenance and guarantee:
Inspect the tool when delivered. Damage sustained during shipment is not covered by the guarantee. Bartec will
accept no responsibility for material or bodily harm resulting from inappropriate use of the product, failure to
maintain it, or incorrect storage conditions.
Bartec provides training for clients desirous of acquiring the knowledge required for the correct use of its products.
Only personnel authorized by Bartec are permitted to make any repairs that may be necessary. This tool is
guaranteed against any manufacturing fault for 12 months as of date of invoice (parts and labour) only if product
has been correctly used. Serial number must stay readable and proof of purchase must be retained for presentation
upon request.
Bartec Auto ID Ltd
Unit 9
Redbrook Business Park
Wilthorpe Road
Barnsley
S75 1JN
+44 (0) 1226 770581
TAP100/200 User Guide R.5.3 2019
6 | Page
BEFORE GETTING STARTED
Before you get started using your Tyre Tool, there are a few items to be aware of.
Charge your tool
The tool is shipped with a fully charged battery, but due to shelf drain it may require charging. It is
recommended to charge your tool 2+ hours before use.
(See page 10 for charging instructions)
Register your tool
You can register your Bartec tool at www.bartecautoid.com. Follow the on-screen prompts filling in your
information and tool serial number. A valid serial number and supplier is required to process your registration,
which can take up to 24hrs once submitted.
(See page 16 for instructions)
Update your Tool
Once your tool is registered, verify the software level loaded to the level available online and update your tool
if necessary. Refer to section on tool updating for further instruction.
(See page 19 for update instructions)
Calibration depth and pressure
We recommend you carry out a monthly calibration of the depth gauge to ensure your tool functions
accurately. (Please use the setup menu and follow the displayed instructions)
We recommend you arrange for Pressure calibration annually. For further help please contact:
www.bartecautoid.com
TAP100/200 User Guide R.5.3 2019
7 | Page
KIT COMPONENTS
The TAP100 or TAP200 kit inside the tool box includes:
Tread Depth and Pressure Reader
Rugged Rubber boot
Pressure hose
USB cable
Wireless wall charger
User Manual
Carry case
Pin Cover
Identifying Kit Components and Features
The tool is battery operated and measures tread depth with its steel pin and tyre pressure with the included
hose.
Note:
The major difference between the TAP100 and the TAP200 is the length of the tread depth pin.
The TAP100 has a 15mm pin which is used for passenger vehicle tyres.
The TAP200 has a 25mm pin which is used for vehicles with deeper tread depths.
Wireless
wall charger
and power
supply
Tread Depth
and Pressure
Reader
Pressure
hose
User
manual
TAP100/200 User Guide R.5.3 2019
8 | Page
MENU NAVIGATION
The tool’s menu system provides a hierarchy of instructions and commands. The top line of the display will
always indicate the current menu selected.
The menu system is navigated by the directional keys:
Up Arrow
Key Navigates up within the current menu selection
Down Arrow
Key Navigates down within the current menu selection
ENTER Key Navigates to the next menu or actions
the currently highlighted item
Back/ESC
and ON Key
Press to turn on
Navigates to the previous menu item
All menus wrap around. The enter key will often move to a sub menu.
TAP100/200 User Guide R.5.3 2019
9 | Page
TOOL POSITIONING
Proper tool positioning is important to insure correct measurement of tyre data. Place the tool on the tyre,
use the pin on the back side of the tool for measuring tyre tread depth and connect the hose to the valve in
order to check tyre pressure.
Tread Depth and Pressure Measurement
Tread Depth
To check the tyre’s tread depth, hold the pin on the backside of the tool in each groove, press to the bottom
and wait for the tool’s signal.
Pressure
In order to measure tyre pressure, connect the hose to the valve of the wheel and wait for the tool’s signal.
MOT Testing
When using the tool for UK MOT Testing please follow the testing procedures and pass/fail limits that are
laid out in Section 4 of the relevant DVSA MOT Inspection Manual.
TOOL CONNECTIONS
Hose connection for tyre pressure measurement.
TAP100/200 User Guide R.5.3 2019
10 | Page
CHARGING TOOL
The tool is supplied with a wall-mounted Inductive Charging Cradle with a
wall adapter power supply. For optimal performance, return the tool
securely to the cradle when not in use to ensure that the battery is
charged.
NOTICE: Only use the power supply or USB cable that is included in the
tool kit to charge this tool. The use of un-approved power supplies may
damage your tool and will void the tool warranty.
The tool comes with the rechargeable battery already installed. Battery replacement must be done at the
factory.
Battery Indicator
The battery indicator in the lower right of the tool screen indicates the estimated power status of the tool’s
rechargeable battery:
FULL Charge
Partial Charge - charging shortly is suggested.
Little power in the battery- charging required.
The battery is FLAT, requires charging
When an insufficient amount of power remains, the tool will display a flashing battery icon and power off.
TAP100/200 User Guide R.5.3 2019
11 | Page
POWER ON/OFF SEQUENCE
The TAP100/200 is powered up using the Back/On key.
To power the tool on, press the Back/On key. The display will light, indicating the tool name. The tool will
then display the Main menu.
Power down the tool by selecting “Off” from the Main menu and pressing the Enter key. “Goodbye” is
displayed, and the tool will power off.
Auto Off can be configured under “Setup” from the Main menu.
IMPORTANT NOTE: The tool does not store data after being powered off. Be sure to send any existing
measurements to TPMS Desktop before the tool turns off for any reason.
HOME MENU
The home screen, which provides access to the main functional items of the tool, is shown after power up.
From the Main menu, highlighting a selection and pressing the Enter key provides access to the following
features:
START MEASUREMENTS
Pressing the Enter Key, the vehicle audit screen appears, where tread depth
and air pressure is measured.
TAP100/200 User Guide R.5.3 2019
12 | Page
VEHICLE AUDIT SCREEN
On entry to the audit screen, the Left Front wheel will be flashing, prompting the operator to start at this
wheel position. Pressing the Enter button will open the tyre audit screen with the arrow pointing on the left
groove of the tyre.
The flashlight is now illuminated. Hold/press the pin into the marked groove of the tyre,
the tool will then beep and take the depth reading. Its depth is measured and saved for
this position. The arrow will then automatically move on to the next groove and
respectively to the next tyre (Right Front, Right Rear, Left Rear and then Spare Wheel).
Three readings should be taken for each tyre.
Tread Depth can be measured and displayed in Millimetres or Inch Fractions (these can
be changed in the setup menu).
To take the tyre pressure, simply connect the hose to the tool and then the valve of the
tyre. Complete the process by selecting Tyre Condition and Manufacturer in the menu. Once all data is entered
click accept for saving the data and returning to the vehicle audit screen. Continue with the remaining tyres.
Pressure can be measured and displayed in PSI, Bar or kPa (these can be changed in the setup menu).
TREAD DEPTH AND PRESSURE READ
The reading is shown by a colour coding system. Green for okay (over 2.3mm tread available), amber for
recommended tyre change in the near future (between 1.6-2.2mm tread available) and red for immediate tyre
change (below 1.5mm). These values can all be changed/updated in the settings menu, tyre tread bands.
A flat surface display shows that the tyre is wearing evenly. The image shows even
tyre wear with a tread depth still within a safe (green) range.
A display where the tyre surface curves inward indicates that the tyre’s surface is
wearing faster in the centre than on the sides. This is a common side effect of
over-inflated tyres.
A display where the tyre surface curves outward indicates that the tyre’s tread is
wearing faster on the sides than in the centre. This is a common side effect of
under-inflated tyres.
TAP100/200 User Guide R.5.3 2019
13 | Page
A display where the tyre surface is slanted outward or inward
indicates that the tyre’s tread is wearing faster on one side in
comparison to the opposite side. This is a common side effect
of a tyre or tyres being out of alignment.
SEND DATA
When paired to your PC or tablet, the tool will send existing audit data to your device for use within the
TPMS Desktop application (see Page 18 for information on TPMS Desktop and for details on pairing via
Bluetooth on Page 21).
TAP100/200 User Guide R.5.3 2019
14 | Page
CLEAR VEHICLE DATA
Deletes all tire data stored on the tool. After pressing the Enter key on Clear Vehicle Data from the Main
menu, you will be prompted to confirm whether you wish to delete all data. Use the Arrow keys to highlight
Yes or No and press Enter to confirm.
WHEELS
Allows selecting the correct number of tires for a vehicle. The Main menu will display the current setting. To
change this setting, press the Enter key and use the Arrow keys to highlight your selection. Press Enter to
save.
SETUP
Setup is a sub-menu in which you will find all the options to adapt the tool to your needs and preferences.
Calibration: The user can carry out calibration of the tread depth. It is recommended this is carried out every
month.
Bluetooth Pair: The tool searches Bluetooth-capable devices in its reach and displays all of them, so the user
can select one.
Brightness: Change the brightness of the display using the up and down keys.
Depth Units: Select the unit for the display of the tread depth, Millimetres or Inch Fractions.
Pressure Units: Choose between PSI, Bar or kPa.
Tyre Selection: Select Seasonal or none. The option Seasonal enables the selection of Summer, Winter or All
Season Tyres before the measurement.
Tyre Tread Bands: Choose between Standard, Summer, Winter or All Season Tyres. Change the respective
tread depth limits for the tyre types to your needs and your local regulations.
Auto Off: Select the time the tool switches off automatically when not in use.
TAP100/200 User Guide R.5.3 2019
15 | Page
Language: Select Language for the tool.
Update Tool: Receive the latest software on your tool by choosing ‘Update Mode’ from the menu.
TOOL INFO
Sub-menu containing important information about the tool itself.
Tool Info
Displays the following information:
- Software version currently installed
- Build date of the installed Software
- Serial number of the tool
- Total number of tread measurements taken (Tread Meas.)
- Total number of pressure measurements taken (Pressure Meas.)
Note that the number of tread/pressure measurements is a running total, and is not cleared when the tool is
recalibrated or data is sent to a device via Bluetooth.
TAP100/200 User Guide R.5.3 2019
16 | Page
REGISTERING YOUR TOOL
It is of great importance to register your tool. The registration enables:
#1 Access to Software Updates
#2 Access to new Manuals
#3 Access to Technical Service Bulletins
#4 Answers to FAQs
#5 Activation of your product warranty
#6 Protection of your investment
#7 Information on new promotion
#8 Receipt of our TPMS Newsletter
To register your tool, navigate to the Bartec TPMS website at www.tools.bartecautoid.com.
The first page you will see is the TPMS Tool Support Center page, showing the latest software release versions
of the respective Bartec tools.
Select ‘Register’ to create a new account. It is important to fill in all fields completely and accurately. This
information will help Bartec remain in contact with you regarding updates and other important TPMS
information. Choose a username (without a space) and password.
If your details are accepted, you get the following message.
The following email should arrive within a few minutes:
TAP100/200 User Guide R.5.3 2019
17 | Page
Following the ‘Confirm account’ link will take you back to the website.
This page is showing that you are now a registered user. Click onthis pageto log in.
From now on you only need to log in as a registered user:
After Login, you are shown your personal settings, which can be changed or not, as required.
Selecting Tools gives you the option to register a new tool. The serial number is in the ‘Tool Info’ menu.
Note that this Serial Number is validated by the website and it must be correct, including the first zero.
If the number is accepted you will see the tool listed, along with a “TPMS Desktop required” button which will
lead to the Bartec website, where the free Software can be downloaded:
TAP100/200 User Guide R.5.3 2019
18 | Page
TPMS DESKTOP
“TPMS Desktop is free PC software that is the easiest way to update all of your Bartec tools
without logging in to this website, and it also has many other benefits. TPMS Desktop is required
to update the TAP100, TAP200 and the TPMS PAD, and is the best way to update the Tech300,
Tech400 and Tech500.”
Go to https://tools.bartecautoid.com/tpmsdesktop/ to download your free copy now!
TPMS Desktop features:
Update: Automatically retrieve update files from your current
registered account
Reports: Complete job reports recorded and stored for when
you need them
Vehicle List: Lookup TPMS information for a vehicle quickly
and easily
Settings: Configure your settings for Bluetooth and
Wi-Fi configuration
PAD: Launches the software to run your TPMS PAD
Display: Software available to display vehicle details, tyre pressure and tread depth
readings on a TV or Monitor for Tyre shop garages or waiting rooms
Training Videos: Learn about TPMS
TAP100/200 User Guide R.5.3 2019
19 | Page
UPDATING YOUR TOOL VIA TPMS DESKTOP
Click on Update, the software will be automatically be downloaded to your tool, and it will be ready to use.
Updating the TAP only works with the TPMS Desktop installed on your computer.
Power on your tool. Go to the Main Menu, select Setup and Update Tool.
The tool will prompt user to “Please Connect USB”.
Insert the USB cable to the tool and connect it to the PC with TPMS Desktop installed.
Click the Update button on the TPMS Desktop and it will show the picture below:
This will be shown under Connected Tools if you connect a tool and click Refresh.
If you already had a tool connected when you clicked on the Update tab, you see this picture straight away:
Update: will only be available to click if a newer version is available to install
Recover Software: this will reinstall the current version, if you think that you have any problems
with your tool
Register: you need to register your tool once in order to use the updates service
TAP100/200 User Guide R.5.3 2019
20 | Page
The Register button takes you to the website:
Reports
Search, view and print job reports. This preformatted and detailed record
contains the necessary job information that you and your customers
need. Sort or filter reports by date, make, model and year. Simply print a
report and attach it to the invoice as proof of work completed. Use
reports to create customer receipts and limit liability.
Vehicle Lookup
Browse our extensive vehicle and sensor database. Search by make, model and year to quickly find the data
you need: OBD location, TPMS relearn, sensor information it’s all there with TPMS Desktop. Plus, the
database is regularly updated.
TPMS PAD
Program sensors using the dedicated, easy to use TPMS PAD. Simply
connect your TPMS PAD to your PC using a USB cable to program and test
sensors with ease. Copy and create a universal sensor with Copy Sensor and
Create Sensor features only available with TPMS Desktop.
TAP100/200 User Guide R.5.3 2019
21 | Page
System Settings
Configure the TPMS Desktop Application to meet your tyre shop’s needs.
Want to connect with Bluetooth. Connectivity is just a few clicks away
with TPMS Desktop.
Your tool will connect wirelessly to the TPMS Desktop using Bluetooth technology.
While this will work easily with most computers, some have software which can be
difficult to setup. In these rare circumstances, or if your computer does not support
Bluetooth, you can use a Bluetooth adaptor.
Go to https://tools.bartecautoid.com/tpmsdesktop/ to download your free copy now!
SETTINGS
In order to use your tool with Bluetooth, you can either use the Send Data option in the Main Menu or go
into Setup and then choose Bluetooth Pair.
In Windows 7:
Click the Windows Start button, type “Bluetooth” into the search field, then
select “Change Bluetooth settings”. Under the Options tab, ensure the following
boxes are checked:
• Allow Bluetooth devices to find this computer
• Allow Bluetooth devices to connect to this computer
Click OK to save these settings.
In Windows 10:
Click Windows Start > Settings > Devices > Bluetooth. Ensure the
Bluetooth switch is in the On position. Close the window to save this
setting.
Next, open TPMS Desktop on your device. Go to Settings and expand the
Bluetooth section. Ensure the boxes for “Connectable” and “Discoverable
are checked.
TAP100/200 User Guide R.5.3 2019
22 | Page
On the tool, select “Bluetooth Pair” from the Setup menu, and the tool will
search for available devices. Locate your device in the list and select it with
the Enter key.
The tool will prompt when it has paired successfully. TPMS Desktop will
also prompt upon a successful Bluetooth connection.
The tool is now set up to send audit data to TPMS Desktop on your device.
Display
NEW: Garage/Tyre shop display screen functionality enables the technician to show the customer their
vehicle readings on a TV or monitor in the garage or waiting room. Gives the customer more confidence and
sells more tyres.
TAP100/200 User Guide R.5.3 2019
23 | Page
TECHNICAL SPECIFICATION
Power Supply: Lithium Polymer rechargeable battery, not user serviceable.
Measurement: TAP100: 15mm replaceable steel pin with profiled end
TAP200: 25mm replaceable steel pin with profiled end
Screen: High resolution, sunlight readable, 1.6” colour graphics display 240 * 240
pixels
Tool: Rugged ABS/Polycarbonate enclosure resistant to automotive fluids
complete with rubber cover
Waterproof: Rated IP54 for water and dust ingress
Pressure: Built in electronic pressure gauge and Quick release lightweight pressure
hose
Working environment: Temperature 0°C - 45°C, Humidity: 20-55%
Storage environment: Temperature - 10°C - 50°C, Humidity: 20-60%
Dimensions: 180mm x 51mm x 53mm
Weight (incl. batteries): 295g
TAP100/200 User Guide R.5.3 2019
24 | Page
BARTEC PRODUCT RANGE & ACCESSORIES
TPMS Tool
TECH500
TPMS Tool
TECH300
Tread Depth and
Pressure Tool
TAP100
&TAP200
ACCESSORIES
TPMS
Wireless
charging PAD
Audit Report
Mini Printer
CUB Adapter
programming
Fixture
Wall mountable wireless charging stations for the workshop or mobile working
Diagnostics
Tool
TECH100
TPMS sensor
Programming
PAD
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bartec Tap 100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bartec Tap 100 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Bartec Tap 100

Bartec Tap 100 Gebruiksaanwijzing - Deutsch - 24 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info