784763
12
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
Manufactured under one or more of these patents.
U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2, Canadian Patent: 2342614,
Australian patent: 2373248 other patents both foreign and domesc applied for and pending. All material copyright of Balboa Water Group.
42281_A | Compable with SpaTouch 1 & 2 12 03.17
The Settings Screen
Priming the Pumps
Exiting Priming Mode
As soon as the Priming Mode screeen appears on the panel,
select the “Jets 1” button once to start Pump 1 in low-speed
and then again to switch to high-speed. Also, select the other
pumps, to turn them on. The pumps should be running in high-
speed to facilitate priming. If the pumps have not primed after
2 minutes, and water is not flowing from the jets in the spa,
do not allow the pumps to continue to run. Turn off the pumps
and repeat the process. Note: Turning the power off and back
on again will initiate a new pump priming session. Sometimes
momentarily turning the pump off and on will help it to prime.
Do not do this more than 5 times. If the pump(s) will not prime,
shut off the power to the spa and call for service.
Important: A pump should not be allowed to run without priming for more than 2 minutes. Under NO circumstances should a pump
be allowed to run without priming beyond the end of the 4-5 minute priming mode. Doing so may cause damage to the pump and
cause the system to energize the heater and go into an overheat condition.
The system will automatically enter the normal heating and filtering at the end of the priming mode, which lasts 4-5 minutes.
You can manually exit Priming Mode by pressing the “Back” button on the
Priming Mode Screen. Note that if you do not manually exit the priming
mode as described above, the priming mode will be automatically terminated
after 4-5 minutes. Be sure that the pump(s) have been primed by this time.
Once the system has exited Priming Mode, the top-side panel will display the Main Screen, but the display will not show the water
temperature yet, as shown below. This is because the system requires approximately 1 minute of water flowing through the heat-
er to determine the water temperature and display it.
*M0XX is a Message Code.
– – – –
°F – – – –°C
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Balboa SpaTouch2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Balboa SpaTouch2 in de taal/talen: Engels als bijlage per email.

De handleiding is 2.12 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info