661201
10
Verklein
Vergroot
Pagina terug
1/140
Pagina verder
INTRODUCTION
i
Thank you for purchasing this machine. Before using this machine, carefully read the “IMPORTANT SAFETY
INSTRUCTIONS”, and then study this manual for the correct operation of the various functions.
In addition, after you have finished reading this manual, store it where it can quickly be accessed for future reference.
Please read these safety instructions before attempting to use the machine.
DANGER - To reduce the risk of electrical shock
1Always unplug the machine from the electrical outlet immediately after using, when cleaning, making any user
servicing adjustments mentioned in this manual, or if you are leaving the machine unattended.
WARNING - To reduce the risk of burns, fire, electrical shock, or injury to
persons.
2Always unplug the machine from the electrical outlet when making any adjustments mentioned in the instruction
manual.
To unplug the machine, switch the machine to the symbol “O” position to turn it off, then grasp the plug and pull
it out of the electrical outlet. Do not pull on the cord.
Plug the machine directly into the electrical outlet. Do not use an extension cord.
Always unplug your machine if there is a power failure.
3Electrical Hazards:
This machine should be connected to an AC power source within the range indicated on the rating label. Do not
connect it to a DC power source or converter. If you are not sure what kind of power source you have, contact a
qualified electrician.
This machine is approved for use in the country of purchase only.
4Never operate this machine if it has a damaged cord or plug, if it is not working properly, has been dropped or
damaged, or water is spilled on the unit. Return the machine to the nearest authorized Baby Lock retailer for
examination, repair, electrical or mechanical adjustment.
While the machine is stored or in use if you notice anything unusual, such as an odor, heat, discoloration or
deformation, stop using the machine immediately and unplug the power cord.
When transporting the machine, be sure to carry it by its handle. Lifting the machine by any other part may
damage the machine or result in the machine falling, which could cause injuries.
When lifting the machine, be careful not to make any sudden or careless movements, which may cause a
personal injury.
INTRODUCTION
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
ii
5Always keep your work area clear:
Never operate the machine with any air openings blocked. Keep ventilation openings of the machine and foot
control free from the build up of lint, dust, and loose cloth.
Do not store objects on the foot controller.
Do not use extension cords. Plug the machine directly into the electrical outlet.
Never drop or insert foreign objects in any opening.
Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
Do not use the machine near a heat source, such as a stove or iron; otherwise, the machine, power cord or
garment being sewn may ignite, resulting in fire or an electric shock.
Do not place this machine on an unstable surface, such as an unsteady or slanted table, otherwise the machine
may fall, resulting in injuries.
6Special care is required when sewing:
Always pay close attention to the needle. Do not use bent or damaged needles.
Keep fingers away from all moving parts. Special care is required around the machine needle.
Switch the machine to the symbol “O” position to turn it off when making any adjustments in the needle area.
Do not use a damaged or incorrect needle plate, as it could cause the needle to break.
Do not push or pull the fabric when sewing, and follow careful instruction when free motion stitching so that
you do not deflect the needle and cause it to break.
7This machine is not a toy:
Your close attention is necessary when the machine is used by or near children.
The plastic bag that this machine was supplied in should be kept out of the reach of children or disposed of.
Never allow children to play with the bag due to the danger of suffocation.
Do not use outdoors.
8For a longer service life:
When storing this machine, avoid direct sunlight and high humidity locations. Do not use or store the machine
near a space heater, iron, halogen lamp, or other hot objects.
Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders can damage the
case and machine, and should never be used.
Always consult the Instruction and Reference Guide when replacing or installing any assemblies, the presser feet,
needle, or other parts to assure correct installation.
9For repair or adjustment:
If the light unit is damaged, it must be replaced by an authorized Baby Lock retailer.
In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of
the Instruction and Reference Guide to inspect and adjust the machine yourself. If the problem persists, please
consult your local authorized Baby Lock retailer.
Use this machine only for its intended use as described in the manual.
Use accessories recommended by the manufacturer as contained in this manual.
The contents of this manual and specifications of this product are subject to change without notice.
For additional product information, visit our website at www.babylock.com
IMPORTANT SAFETY INSTRUCTIONS
iii
SAVE THESE INSTRUCTIONS
This machine is intended for household use.
FOR USERS IN COUNTRIES EXCEPT EUROPEAN COUNTRIES
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
FOR USERS IN EUROPEAN COUNTRIES
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
FOR USERS IN THE UK, EIRE, MALTA
AND CYPRUS ONLY
IMPORTANT
In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the mark,
rating as marked on plug.
Always replace the fuse cover. Never use plugs with the fuse cover omitted.
If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your
authorized Baby Lock retailer to obtain the correct lead.
ABOUT THIS MANUAL
iv
This manual was written for several machine models.
The screen displays may differ from the ones displayed on your machine.
Refer to the Quick Reference Guide for details on accessories, settings screen and pre-programmed stitch patterns.
First, read “Functions available with each model” and “Using the utility stitch tables in the “Sewing” section” on page B-6.
ABOUT THIS MANUAL
WHAT YOU CAN DO WITH THIS MACHINE
B Basic operations
After purchasing your machine, be sure to read this section first. This section provides details on the initial setup
procedures as well as descriptions of this machine’s more useful functions.
Chapter 1 GETTING READY
Page B-2
To learn the operation of the principal parts and the screens
Chapter 2 STARTING TO SEW
Page B-31
To learn how to prepare for sewing and basic sewing operations
S Sewing
This section describes procedures for using the various utility stitches as well as other functions. It provides details on
basic machine sewing in addition to the more expressive features of the machine, such as sewing tubular pieces and
buttonholes.
Chapter 1 SEWING ATTRACTIVE FINISHES
Page S-2
Tips for sewing attractive finishes and various fabrics
Chapter 2 UTILITY STITCHES
Page S-6
Sew pre-programmed frequently used stitches
D Decorative sewing
This section provides instructions on sewing character stitches and decorative stitches as well as on adjusting and editing
them.
Chapter 1 CHARACTER / DECORATIVE STITCHES
Page D-2
The variety of stitches widen your creativity
A Appendix
This section provides important information for operating this machine.
Chapter 1 MAINTENANCE AND TROUBLESHOOTING
Page A-2
The various maintenance and troubleshooting procedures are described.
CONTENTS
v
INTRODUCTION.................................................. i
IMPORTANT SAFETY INSTRUCTIONS ................. i
ABOUT THIS MANUAL ...................................... iv
WHAT YOU CAN DO WITH THIS MACHINE.... iv
B Basic operations
Chapter 1 GETTING READY 2
Names of Machine Parts and Their Functions ...... 2
Machine ................................................................................ 2
Needle and presser foot section .................................................. 3
Operation buttons.................................................................. 4
Operation panel and operation keys ...................................... 4
Using the flat bed attachment ................................................ 5
Included accessories .............................................................. 6
Functions available with each model ..................................... 6
Using the utility stitch tables in the “Sewing” section ............. 6
Turning the Machine On/Off................................ 7
Turning on the machine......................................................... 8
Turning off the machine......................................................... 8
Select machine setting for the first time .................................. 8
LCD ...................................................................... 9
Viewing the LCD ................................................................... 9
Settings screen ..................................................................... 10
Choosing the display language............................................. 12
Adjusting input sensitivity for operation keys ....................... 12
Winding/Installing the Bobbin............................ 13
Winding the bobbin ............................................................. 13
Installing the bobbin ............................................................ 16
Upper Threading ................................................ 19
Threading the upper thread.................................................. 19
Threading the needle ........................................................... 21
Threading the needle manually (without using the needle
threader) .............................................................................. 22
Pulling up the bobbin thread................................................ 22
Using the twin needle .......................................................... 23
Replacing the Needle ......................................... 26
Fabric/thread/needle combinations ...................................... 26
Checking the needle ............................................................ 27
Replacing the needle ........................................................... 27
Replacing the Presser Foot ................................. 29
Replacing the presser foot .................................................... 29
Removing and attaching the presser foot holder................... 30
Chapter 2 STARTING TO SEW 31
Sewing................................................................ 31
Stitch selection methods ...................................................... 31
Selecting a stitch pattern ...................................................... 32
Sewing a stitch..................................................................... 33
Sewing reinforcement stitches.............................................. 35
Automatic reinforcement stitching ....................................... 35
Setting the Stitch ................................................ 37
Setting the stitch width......................................................... 37
Setting the stitch length ........................................................ 37
Setting the thread tension..................................................... 38
Saving stitch settings ............................................................ 39
Useful Functions................................................. 40
Automatically cutting the thread .......................................... 40
Mirroring stitches ................................................................. 40
Adjusting the presser foot pressure ....................................... 41
Automatic Fabric Sensor System (Automatic presser foot
pressure) .............................................................................. 41
Pivoting ............................................................................... 41
Sewing with free motion mode ............................................ 42
Hands-free raising and lifting of the presser foot ................... 43
Stitch Setting Chart............................................ 44
S Sewing
Chapter 1 SEWING ATTRACTIVE
FINISHES 2
Sewing Tips.......................................................... 2
Trial sewing............................................................................ 2
Changing the sewing direction
.................................................. 2
Sewing curves ........................................................................ 2
Sewing cylindrical pieces ....................................................... 2
Sewing an even seam allowance ............................................ 3
Sewing Various Fabrics ........................................ 4
Sewing thick fabrics ............................................................... 4
Sewing thin fabrics ................................................................. 4
Sewing stretch fabrics............................................................. 5
Sewing leathers or vinyl fabrics .............................................. 5
Sewing hook-and-loop fastener tape....................................... 5
Chapter 2 UTILITY STITCHES 6
Basic Stitching...................................................... 6
Basting ................................................................................... 6
Basic stitching ........................................................................ 6
Blind Hem Stitching ............................................. 8
Overcasting Stitches .......................................... 11
Sewing overcasting stitches using overcasting foot “G” ........ 11
Sewing overcasting stitches using zigzag foot “J”.................. 12
Sewing overcasting stitches using the side cutter
(sold separately with some models) ...................................... 12
Buttonhole Stitching/Button Sewing .................. 14
Buttonhole sewing................................................................ 14
Button sewing ...................................................................... 17
Zipper Insertion ................................................. 19
Inserting a centered zipper ................................................... 19
Inserting a side zipper .......................................................... 20
Zipper/piping Insertion...................................... 23
Inserting a centered zipper ................................................... 23
Inserting a piping.................................................................. 24
Sewing Stretch Fabrics and Elastic Tape............. 25
Stretch stitching.................................................................... 25
Elastic attaching ................................................................... 25
Appliqué, Patchwork and Quilt Stitching........... 26
Appliqué stitching ................................................................ 26
Patchwork (crazy quilt) stitching........................................... 27
Piecing ................................................................................. 27
Quilting................................................................................ 29
Free motion quilting ............................................................. 30
Satin stitching using the sewing speed controller .................. 34
Reinforcement Stitching..................................... 35
Triple stretch stitching .......................................................... 35
Bar tack stitching.................................................................. 35
Darning................................................................................ 36
Eyelet Stitching .................................................. 38
Attaching Patches or Emblems to Shirt Sleeves
.... 39
Decorative Stitching .......................................... 41
Fagoting ............................................................................... 41
Scallop stitching ................................................................... 42
Smocking ............................................................................. 42
Shell tuck stitching ............................................................... 43
Joining.................................................................................. 43
Heirloom stitching................................................................ 44
CONTENTS
CONTENTS
vi
D Decorative sewing
Chapter 1 CHARACTER / DECORATIVE
STITCHES 2
Sewing the Various Built-in Decorative Patterns
.... 2
Selecting stitch patterns .......................................................... 2
Deleting a pattern................................................................... 3
Sewing attractive finishes ....................................................... 3
Basic sewing .......................................................................... 4
Combining patterns ................................................................ 5
Repeating combined patterns ................................................. 5
Checking the selected pattern................................................. 6
Changing the pattern size ....................................................... 6
Changing the stitch density..................................................... 6
Changing the pattern length ................................................... 7
Changing character spacing ................................................... 7
Creating step stitch patterns.................................................... 7
Mirroring a pattern image....................................................... 8
Returning to the beginning of the pattern................................ 9
Saving a pattern...................................................................... 9
Retrieving a pattern .............................................................. 10
Realigning the pattern .......................................................... 10
A Appendix
Chapter 1 MAINTENANCE AND
TROUBLESHOOTING 2
Care and Maintenance.......................................... 2
Restrictions on oiling.............................................................. 2
Precautions on storing the machine........................................ 2
Cleaning the LCD screen........................................................ 2
Cleaning the machine surface ................................................ 2
Cleaning the race ................................................................... 2
Troubleshooting.................................................... 4
Frequent troubleshooting topics ............................................. 4
Upper thread tightened up ..................................................... 4
Tangled thread on wrong side of fabric .................................. 5
Incorrect thread tension.......................................................... 6
Fabric is caught in the machine and cannot be removed ........ 7
When the thread became tangled under the bobbin winder
seat ...................................................................................... 10
List of symptoms................................................................... 12
Error messages...................................................................... 17
Operation beep .................................................................... 20
Nothing appears in the LCD ................................................. 20
Specifications ..................................................... 20
Index .................................................................. 21
Basic
operations
This section provides details on the initial setup procedures as well as descriptions of this
machine’s more useful functions.
Page number starts with “B” in this section.
Chapter1 GETTING READY....................................................B-2
Chapter2 STARTING TO SEW ..............................................B-31
Names of Machine Parts and Their Functions
B-2
The names of the various parts of the machine and their functions are described below. Before using the machine,
carefully read these descriptions to learn the names of the machine parts and their locations.
Machine
Front view
1 Top cover
Open the top cover to place the spool of thread on the spool
pin.
2 Thread guide plate
Pass the thread around the thread guide plate when threading
the upper thread.
3 Bobbin winding thread guide and pretension disk
Pass the thread under this thread guide and around the
pretension disk when winding the bobbin thread.
4 Spool cap
Use the spool cap to hold the spool of thread in place.
5 Spool pin
Place a spool of thread on the spool pin.
6 Bobbin winder
Use the bobbin winder when winding the bobbin.
7 LCD (liquid crystal display)
Settings for the selected stitch and error messages appear in
the LCD. (page B-9)
8 Operation panel
From the operation panel, stitch settings can be selected and
edited, and operations for using the machine can be selected
(page B-4).
9 Knee lifter mounting slot
Insert the knee lifter into the knee lifter mounting slot.
0 Knee lifter
Use the knee lifter to raise and lower the presser foot.
(page B-43)
A Operation buttons and sewing speed controller
Use these buttons and the slide to operate the machine.
(page B-4)
B Flat bed attachment
Insert the presser foot accessory tray into the accessory
compartment of the flat bed attachment. Remove the flat bed
attachment when sewing cylindrical pieces such as sleeve
cuffs.
C Thread cutter
Pass the threads through the thread cutter to cut them.
D Needle threader lever
Use the needle threader lever to thread the needle.
E Thread tension dial
(Equipped on some models. Refer to page B-6)
Use the dial to adjust the upper thread tension. (page B-38)
Right-side/rear view
1 Handwheel
Turn the handwheel toward you (counterclockwise) to raise and
lower the needle to sew one stitch.
2 Handle
Carry the machine by its handle when transporting.
3 Presser foot lever
Raise and lower the presser foot lever to raise and lower the
presser foot.
4 Feed dog position switch
Use the feed dog position switch to lower the feed dogs.
5 Main power switch
Use the main power switch to turn the machine on and off.
6 Power supply jack
Insert the plug on the power supply cord into the power supply
jack.
7 Foot controller
Depress the foot controller to control the speed of the machine.
(page B-34)
8 Air vent
The air vent allows the air surrounding the motor to circulate.
Do not cover the air vent while the machine is being used.
9 Foot controller jack
Insert the plug on the end of the foot controller cable into the
foot controller jack.
Chapter 1
GETTING READY
Names of Machine Parts and Their Functions
a
b
c
d
e
f
h
i
j
k
l
m
n
o
g
a
b
c
d
e
f
g
h
i
Names of Machine Parts and Their Functions
GETTING READY
Basic operations B-3
B
Needle and presser foot section
1 Needle bar thread guide
Pass the upper thread through the needle bar thread guide.
2 Needle plate
The needle plate is marked with guides for sewing straight
seams.
3 Needle plate cover
Remove the needle plate cover to clean the bobbin case and
race.
4 Bobbin cover/bobbin case
Remove the bobbin cover, and then insert the bobbin into the
bobbin case.
5 Feed dogs
The feed dogs feed the fabric in the sewing direction.
6 Presser foot
The presser foot applies pressure consistently on the fabric as
the sewing takes place. Attach the appropriate presser foot for
the selected stitch.
7 Presser foot holder
The presser foot is attached onto the presser foot holder.
8 Presser foot holder screw
Use the presser foot holder screw to hold the presser foot in
place. (page B-30)
9 Buttonhole lever
Lower the buttonhole lever when sewing buttonholes and bar
tacks or when darning.
Measurements on the needle plate, bobbin cover (with mark)
and needle plate cover
The measurements on the bobbin cover are references for
patterns with a middle (center) needle position. The
measurements on the needle plate and the needle plate cover
are references for stitches with a left needle position.
1 For stitches with a middle (center) needle position
2 For stitches with a left needle position
3 Left needle position on the needle plate <inch>
4 Left needle position on the needle plate <cm>
5 Middle (center) needle position on the bobbin cover
(with mark) <inch>
6 Left needle position on the needle plate cover <inch>
i
b
a
c
d
e
f
g
h
a
b
c
d
e
f
Names of Machine Parts and Their Functions
B-4
Operation buttons
1 “Start/Stop” button
Press the “Start/Stop” button to start or stop sewing. The
machine stitches at a slow speed at the beginning of sewing
while the button is pressed. When sewing is stopped, the
needle is lowered in the fabric. For details, refer to “STARTING
TO SEW” on page B-31.
The button changes color according to the machine’s
operation mode.
2 Reverse stitch button
For straight, zigzag, and elastic zigzag stitch patterns that use
reverse stitches, the machine will sew reverse stitches at low
speed only while holding down the Reverse stitch button. The
stitches are sewn in the opposite position.
For other stitches, use this button to sew reinforcement
stitches at the beginning and end of sewing. Press and hold
this button, and the machine sews 3 stitches in the same spot
and stops automatically. (page B-35)
3 Reinforcement stitch button
Use this button to sew a single stitch repeatedly and tie-off.
For character/decorative stitches, press this button to end with
a full stitch instead of at a mid-point. The LED light beside this
button lights up while the machine is sewing a full motif, and
automatically turns off when the sewing is stopped. (page B-
35)
4 Needle position button
Press the needle position button to raise or lower the needle.
Pressing the button twice sews one stitch.
5 Thread cutter button
Press the thread cutter button after sewing is stopped to cut
both the upper and the bobbin threads. For details, refer to
step
j under “Sewing a stitch” section on page B-33.
6 Presser foot lifter button
(Equipped on some models. Refer to page B-6)
Press this button to lower the presser foot and apply pressure
to the fabric. Press this button again to raise the presser foot.
7 Sewing speed controller
Slide the sewing speed controller to adjust the sewing speed.
Operation panel and operation keys
The keys with * are lit while they are ON.
1 LCD (liquid crystal display)
Settings for the selected stitch and error messages for
incorrect operations appear in the LCD.
For details, refer to “LCD” on page B-9
2 Pivot key *
(Equipped on some models. Refer to page B-6)
Press to activate pivot function.
3 Automatic reverse/reinforcement key *
Press to use the automatic reverse/reinforcement stitching
function.
4 Automatic thread cutting key *
Press to select the automatic thread cutting function.
5 Stitch length keys/Item selection keys
Press to adjust the stitch length or to select the next/previous
items in the settings screen.
6 Thread tension keys (Equipped on some models.
Refer to page B-6)/Value selection keys
Press to adjust the thread tension or to change the value of the
selected item in the settings screen.
7 Settings key
Press to select sewing settings or other settings, or to move to
next pages in the settings screen.
8 Manual memory key
Press to save the adjusted stitch width and length settings. For
models equipped with the thread tension keys (Refer to
page B-6.), the thread tension setting is also saved.
9 Mirror image key
Press to create a mirror image of the selected stitch pattern.
0 Single/repeat sewing key
Press to choose single pattern or continuous patterns.
A Back to beginning key
Press this key to return to the beginning of the pattern.
B Presser foot/Needle exchange key
Press this key before changing the needle, the presser foot,
etc.
This key locks all key and button functions to prevent operation
of the machine.
C Memory key
Press to save stitch pattern combinations to machine memory.
D Reset key
Press to reset the selected stitch to its original settings.
Green: The machine is ready to sew or is sewing.
Red: The machine can not sew.
Orange: The machine is winding the bobbin thread, or
the bobbin winder shaft is moved to the right
side.
CAUTION
Do not press (Thread cutter button) after
the threads have already been cut, otherwise
the needle may break, the threads may
become tangled or damage to the machine
may occur.
b
g
e
l
r
q
s
t
u
a
f
c
d
h
i
j
k
m
n
o
p
v
Names of Machine Parts and Their Functions
GETTING READY
Basic operations B-5
B
E OK key
Press to apply the selection or perform the operation.
F Numeric keys
Use these keys to quickly select one of the ten most often used
stitches. When selecting other stitches, use these keys to type
in the number of the desired stitch.
G Back key
Press this key to cancel the operation and return to the
previous screen.
In addition, pressing this key removes the last pattern added
when combining characters or decorative stitches.
H Character stitch key *
Press to select a character stitch.
I Decorative stitch key *
Press to select a decorative stitch.
J Utility stitch key *
Press to select a utility stitch.
K Preset utility stitch/saved pattern key *
Press to select the utility stitch assigned to a numeric key or to
retrieve a pattern that has been saved.
L Stitch width keys/Settings screen page selection
keys
Press to adjust the stitch width or to move to previous/next
pages in the settings screen.
Using the flat bed attachment
Pull the top of the flat bed attachment to open the accessory
compartments.
A presser foot accessory tray is stored in the accessory
compartment of the flat bed attachment.
1 Storage space of the flat bed attachment
2 Presser foot accessory tray
Note
The operation keys of this machine are
capacitive touch sensors. Operate the keys by
directly touching them with your finger.
The response of the keys varies according to the
user.
The pressure exerted on the keys does not affect
the response of the keys.
Since the operation keys react differently
depending on the user, adjust the setting for the
input sensitivity. (page B-12)
When using an electrostatic touch pen, make
sure that its point is 8 mm or more. Do not use a
touch pen with a thin point or a unique shape.
1
1
2
Names of Machine Parts and Their Functions
B-6
Included accessories
Refer to the Quick Reference Guide for the included accessories and their part codes for your machine model.
Functions available with each model
Specifications differ depending on the machine model. For
the functions available with your sewing machine model,
refer to the table below.
*1
Pattern size can be changed for decorative stitches, satin
stitches and all fonts of character stitches.
*2
Pattern size can be changed for character stitches other
than handwriting font.
Using the utility stitch tables in the “Sewing”
section
The utility stitch numbers differ depending on the model of
your machine.
BLMAV: Aventura
BLMSP: Soprano
BLMLR: Lyric
BL210A: Katherine
Note
(For U.S.A. only) Foot controller: Model T
This foot controller can be used on machine models: BLMSP, BLMLR and BL210A.
BLMSP BLMLR BL210A Page
Automatic fabric
sensor system
(setting)
9
N/A N/A B-41
Fine adjustment
horizontal (setting)
99
N/A D-10
Free motion foot
height (setting)
9
N/A N/A B-42
Free motion mode
(setting)
9
N/A N/A B-42
Pivoting
9
N/A N/A B-41
Presser foot height
(setting)
9
N/A N/A B-11
Presser foot lifter
button
9
N/A N/A B-4
Size selection
(setting)
999
D-6
Step stitch pattern
99
N/A D-7
Thread tension dial N/A N/A
9
B-38
Thread tension key
99
N/A B-38
*1
*1
*2
Stitch name Stitch
BLMAV
Presser foot
BLMSP/BLMLR
BL210A
Stitch number
Basting stitch 1-08 08 07
J
Straight stitch (Left)
1-01
01
* 01*
1-02
02
* 02*
Straight stitch (Middle) 1-03
03
* 03*
Triple stretch stitch 1-05
05
* 05*
Turning the Machine On/Off
GETTING READY
Basic operations B-7
B
Turning the Machine On/Off
WARNING
Use only regular household electricity for the power source. Using other power sources may result in fire,
electric shock, or damage to the machine.
Make sure that the plugs on the power cord are firmly inserted into the electrical outlet and the power
cord receptacle on the machine. Otherwise, a fire or electric shock may result.
Do not insert the plug on the power cord into an electrical outlet that is in poor condition.
Turn the main power to OFF and remove the plug in the following circumstances:
When you are away from the machine
After using the machine
When the power fails during use
When the machine does not operate correctly due to a bad connection or a disconnection
During electrical storms
CAUTION
Use only the power cord included with this machine.
Do not use extension cords or multi-plug adapters with any other appliances plugged into them. Fire or
electric shock may result.
Do not touch the plug with wet hands. Electric shock may result.
When unplugging the machine, always turn the main power to OFF first. Always grasp the plug to remove
it from the electrical outlet. Pulling on the cord may damage the cord, or lead to fire or electric shock.
Do not allow the power cord to be cut, damaged, modified, forcefully bent, pulled, twisted, or bundled.
Do not place heavy objects on the cord. Do not subject the cord to heat. These things may damage the
cord, or cause fire or electric shock. If the cord or plug is damaged, take the machine to your authorized
Baby Lock retailer for repairs before continuing use.
Unplug the power cord if the machine is not to be used for a long period of time. Otherwise, a fire may
result.
When leaving the machine unattended, either the main switch of the machine should be turned to OFF or
the plug must be removed from the electrical outlet.
When servicing the machine or when removing covers, the machine must be unplugged.
For USA only
This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electrical
shock, this plug is intended to fit in a polarized electrical outlet only one way.
If the plug does not fit fully in the electrical outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper electrical outlet. Do not modify the plug in any way.
Turning the Machine On/Off
B-8
Turning on the machine
a
Make sure that the machine is turned off (the main
power switch is set to “ ”), and then plug the power
cord into the power supply jack on the right side of the
machine.
b
Insert the plug of the power cord into a household
electrical outlet.
1 Power supply jack
2 Main power switch
c
Press the right side of the main power switch on the
right side of the machine to turn the machine on (set it
to “I”).
The light, LCD and the “Start/Stop” button light up
when the machine is turned on.
Turning off the machine
When you are finished using the machine, turn it off. In
addition, before transporting the machine to another location,
be sure to turn it off.
a
Make sure that the machine is not sewing.
b
Press the main power switch on the right side of the
machine in the direction of the “ symbol to turn
the machine off.
Select machine setting for the first time
When you first turn on the machine, select the language of
your choice. Follow the procedure below when the settings
screen appears automatically.
a
Use the “-” or “+” key to choose the desired language.
b
Press .
Memo
When the machine is turned on, the needle and
the feed dogs will make a sound when they move;
this is not a malfunction.
If the machine is turned off in the middle of sewing
in the “Sewing” function, the operation will not
resume after turning the power on again.
1
2
LCD
GETTING READY
Basic operations B-9
B
Viewing the LCD
When the power is turned on, the LCD comes on, and the following screen is displayed. The screen will vary slightly depending
on your machine model.
The screen is changed using the keys below the LCD.
LCD
No. Display Item Name Explanation Page
1 Presser foot Shows presser foot to be used. B-29
2 - Stitch preview Shows a preview of the selected stitch. B-32
3 Stitch category Shows the category of the currently selected stitch pattern.
: Preset utility stitch
: Utility stitch
: Decorative stitch (category 1)
: Decorative stitch (category 2)
: Decorative stitch (category 3)
: Character stitch (Gothic font)
: Character stitch (Handwriting font)
: Character stitch (Outline)
: Character stitch (Cyrillic font)
: Character stitch (Japanese font)
B-31
4 - Stitch number Shows the number of the currently selected stitch pattern. B-44
5 Needle position setting Shows single or twin needle mode setting, and the needle stop position.
: Single needle/down position
: Single needle/up position
: Twin needle/down position
: Twin needle/up position
B-10
6 Single/repeat sewing Shows single or continuous patterns sewing mode setting.
: Single sewing mode
: Repeat sewing mode
D-5
7 Horizontal mirror image Appears when the stitch is mirrored. B-40
8 Stitch width Shows the stitch width of the currently selected stitch pattern. B-37
9 Stitch length Shows the stitch length of the currently selected stitch pattern. B-37
0 Thread tension
(Equipped on some
models. Refer to page
page B-6)
Shows the automatic thread tension setting for the currently selected stitch pattern. B-38
5
6
3
1
7
2
8 9 0
4
5
6
3
1
7
2
8 9
4
LCD
B-10
Settings screen
Press to change various sewing machine operations and sewing settings.
Press to move to previous/next pages.
* You can also move to next pages by pressing .
Press to select the next/previous items.
* Press (Downward arrow) to select the next item.
* Press (Upward arrow) to select the previous item.
Press to change the value of the selected item.
1 Page number (The page numbers vary depending on your machine model.)
2 Machine settings
3 Value
1 Use to check the pattern when the specified pattern is not displayed on the screen. For details, refer to “Checking the selected
pattern” in the “Decorative sewing” section.
2 Select the needle stop position (the needle position for when the machine is not being operated) to be up or down.
3 Set to “ON” when using twin needle. For details, refer to “Using the twin needle” on page B-23.
4 Allows the stitch width to be adjusted using the sewing speed controller. For details, refer to “Satin stitching using the sewing
speed controller” in the “Sewing” section.
5 Select either “01 Straight stitch (Left)” or “03 Straight stitch (Middle)” as the utility stitch that is automatically selected when the
machine is turned on.
6 Changes the stitch length when 7 mm satin stitch patterns are selected. For details, refer to “Changing the pattern length” in the
“Decorative sewing” section.
7 Changes the thread density when satin stitch patterns are selected. For details, refer to “Changing the stitch density” in the
“Decorative sewing” section.
8 Changes the character spacing. For details, refer to “Changing character spacing” in the “Decorative sewing” section.
Note
The parameters and number of pages in the settings screens differ depending on the model of your machine. For
details on the settings screen for your machine, refer to the Quick Reference Guide.
2
1
3
1
2
3
4
5
6
7
8
LCD
GETTING READY
Basic operations B-11
B
9 Changes the size of the stitch pattern. For details, refer to “Changing the pattern size” in the “Decorative sewing” section.
0 Adjusts the up and down position of the pattern. For details, refer to “Realigning the pattern” in the “Decorative sewing” section.
A Adjusts the left and right position of the pattern. (Equipped on some models. Refer to page B-6.) For details on this function, refer
to “Realigning the pattern” in the “Decorative sewing” section.
B Adjust the presser foot pressure. The higher the number, the greater the pressure will be. For details on this function, refer to
“Adjusting the presser foot pressure” on page B-41.
C Adjust the height of the presser foot when the presser foot is raised. (Equipped on some models. Refer to page B-6.)
D When set to “ON” the thickness of the fabric is automatically detected by an internal sensor while sewing. This enables the fabric
to be fed smoothly. (Equipped on some models. Refer to page B-6.) For details on this function, refer to “Automatic Fabric Sensor
System (Automatic presser foot pressure)” on page B-41.
E Set to “ON” when sewing with the free motion mode. (Equipped on some models. Refer to page B-6.) For details on this function,
refer to “Sewing with free motion mode” on page B-42.
F Change the height of the presser foot when the machine is set to free motion sewing mode. (Equipped on some models. Refer to
page B-6.) For details on this function, refer to “Sewing with free motion mode” on page B-42.
G Change the height of the presser foot when sewing is stopped when the pivot key is selected. (Equipped on some models. Refer
to page B-6.) For details on this function, refer to “Pivoting” on page B-41.
H Specifies whether or not a beep is sounded with each operation. For details, refer to “Operation beep” in the “Appendix” section.
I Switches the needle area and work area lights to remain “ON” or “OFF”.
J Adjusts the brightness of the LCD.
K When set “ON”, reinforcement stitches are sewn at the beginning and/or end of sewing for a reinforcement stitch pattern, even
when the reverse button is pressed. For details, refer to “Automatic reinforcement stitching” on page B-35.
L Select the level of the input sensitivity for operation keys. For details, refer to “Adjusting input sensitivity for operation keys” on
page B-12.
M Selects the display language. For details, refer to “Choosing the display language” on page B-12.
N Displays the program version.
Memo
Press or to return to the original screen.
9
0
A
B
C
D
E
F
G
H
I
J
K
L
M
N
LCD
B-12
Choosing the display language
a
Press .
b
Select (Language) display.
c
Use the “-” or “+” key to choose the desired language.
d
Press to return to the original screen.
Adjusting input sensitivity for operation keys
You can adjust the sensitivity of the operation keys to five
levels. Display the settings screen to set desired level.
1 Operation keys
a
Select (Input sensitivity) in the settings screen.
b
Adjust the input sensitivity by pressing the “-” or “+”
key.
The lower the setting, the less sensitive the keys will
be; the higher the setting, the more sensitive the keys
will be. The default setting is “3”.
If the machine does not respond when an
operation key is pressed
Hold down (Thread cutter button) and turn on the
machine to reset the settings. Display the settings screen,
and then adjust the settings again.
1
Note
We recommend selecting the highest setting if
an electrostatic touch pen is being used.
Winding/Installing the Bobbin
GETTING READY
Basic operations B-13
B
Winding the bobbin
This section describes how to wind thread onto a bobbin.
a
Open the top cover.
b
Place the bobbin on the bobbin winder shaft so that the
spring on the shaft fits into the notch in the bobbin
.
Press down on the bobbin until it snaps into place.
1 Notch
2 Bobbin winder shaft spring
c
Slide the bobbin winder in the direction of the arrow
until it snaps into place.
The “Start/Stop” button lights up in orange.
d
Remove the spool cap that is inserted onto the spool
pin.
1 Spool pin
2 Spool cap
e
Place the spool of thread for the bobbin onto the spool
pin.
Slide the spool onto the pin so that the spool is
horizontal and the thread unwinds to the front at the
bottom.
If the spool is not positioned so that the thread
unwinds correctly, the thread may become tangled
around the spool pin.
Winding/Installing the Bobbin
CAUTION
Only use the Bobbin (part code: X52800-120)
designed specifically for this machine. Use of
any other bobbin may result in injuries or
damage to the machine.
The included bobbin was designed specifically
for this machine.
If bobbins from other models are used, the
machine will not operate correctly. Use only
the included bobbin or bobbins of the same
type (X52800-120).
X52800-120 is Class15 type bobbin.
* Actual size
1 This model
2 Other models
3 11.5 mm (approx. 7/16 inch)
Memo
When the foot controller is connected, bobbin
winding can be started and stopped with the foot
controller.
2
1
1
2
Winding/Installing the Bobbin
B-14
f
Slide the spool cap onto the spool pin.
Slide the spool cap as far as possible to the right, as
shown, with the rounded side on the left.
CAUTION
If the spool or the spool cap is not installed
correctly, the thread may become tangled
around the spool pin, causing the needle to
break.
Three spool cap sizes are available, allowing
you to choose a spool cap that best fits the size
of spool being used. If the spool cap is too
small for the spool being used, the thread may
catch on the slit in the spool or the machine
may be damaged.
Memo
When sewing with fine, cross-wound thread, use
the small spool cap, and leave a small space
between the cap and the spool.
1 Spool cap (small)
2 Spool (cross-wound thread)
3 Space
When using thread that winds off quickly, such as
transparent nylon thread or metallic thread, place
the spool net over the spool before placing the
spool of thread onto the spool pin.
If the spool net is too long, fold it to fit the size of
the spool.
1 Spool net
2 Spool
3 Spool cap
4 Spool pin
If a spool of thread whose core is 12 mm (1/2
inch) in diameter and 75 mm (3 inches) high is
inserted onto the spool pin, use the thread spool
insert (mini king thread spool).
1 Thread spool insert (mini king thread spool)
2 12 mm (1/2 inch)
3 75 mm (3 inches)
a
c
b
2
1
4
3
Winding/Installing the Bobbin
GETTING READY
Basic operations B-15
B
g
While holding the thread near the spool with your right
hand, as shown, pull the thread with your left hand,
and then pass the thread behind the thread guide cover
and to the front.
1 Thread guide cover
h
Pass the thread under the thread guide plate, and then
pull it to the right.
1 Thread guide plate
i
Pass the thread under the hook on the thread guide,
and then wind it counterclockwise under the
pretension disk.
1 Thread guide
2 Pretension disk
3 Pull it in as far as possible
j
While holding the thread with your left hand, wind the
thread that was pulled out clockwise around the
bobbin five or six times with your right hand.
k
Pass the end of the thread through the guide slit in the
bobbin winder seat, and then pull the thread to the
right to cut it.
1 Guide slit in bobbin winder seat
(with built-in cutter)
l
Slide the sewing speed controller to the right.
1 Speed controller
m
Turn on the machine.
Note
Make sure that the thread passes under the
pretension disk.
1
1
1
2
3
Note
Make sure that the thread between the spool and
the bobbin is pulled tight.
Be sure to wind the thread clockwise around the
bobbin, otherwise the thread will become
wrapped around the bobbin winder shaft.
CAUTION
Be sure to cut the thread as described. If the
bobbin is wound without cutting the thread
using the cutter built into the slit in the bobbin
winder seat, the thread may become tangled in
the bobbin or the needle may bend or break
when the bobbin thread starts to run out.
Note
Bobbin winding speeds may vary depending on
type of thread being wound on bobbin.
1
1
Winding/Installing the Bobbin
B-16
n
Press the “Start/Stop” button once to start winding the
bobbin.
When the foot controller is plugged in, press down on
the foot controller.
1 “Start/Stop” button
o
When the bobbin winding becomes slow, press the
“Start/Stop” button once to stop the machine.
When the foot controller is plugged in, remove your
foot from the foot controller.
p
Use scissors to cut the end of the thread wound around
the bobbin.
q
Slide the bobbin winder shaft to the left, and then
remove the bobbin from the shaft.
r
Slide the sewing speed controller back to desired
sewing speed position.
s
Remove the spool for the bobbin thread from the spool
pin.
Installing the bobbin
Install the bobbin wound with thread.
You can begin sewing immediately without pulling up the
bobbin thread by simply inserting the bobbin in the bobbin
case and guiding the thread through the slit in the needle
plate cover.
a
Press (Needle position button) once or twice to
raise the needle, and then lower the presser foot lever.
b
Press .
If is pressed while the presser foot is raised, an
error message appears: “Lower the presser foot
lever.” or “Use the presser foot lifter button to lower
the presser foot.”
The screen changes, and all keys and operation
buttons are locked (except ).
c
Raise the presser foot lever.
CAUTION
When the bobbin winding becomes slow, stop
the machine, otherwise the machine may be
damaged.
Memo
If the bobbin winder shaft is set to the right side,
the needle will not move. (Sewing is impossible.)
Memo
When the machine is started or the handwheel is
turned after winding the bobbin, the machine will
make a clicking sound; this is not a malfunction.
1
Memo
For details on sewing after pulling up the bobbin
thread, for example, when making gathers or with
free motion quilting, refer to “Pulling up the
bobbin thread” on page B-22.
CAUTION
Use a bobbin that has been correctly wound
with thread, otherwise the needle may break
or the thread tension will be incorrect.
Before inserting or changing the bobbin, be
sure to press (Presser foot/Needle
exchange key) on the operation panel to lock
all keys and buttons, otherwise injuries may
occur if the “Start/Stop” button or any other
button is pressed and the machine starts.
Winding/Installing the Bobbin
GETTING READY
Basic operations B-17
B
d
Slide the bobbin cover latch to the right.
1 Bobbin cover
2 Latch
e
Remove the bobbin cover.
f
Hold the bobbin with your right hand with the thread
unwinding to the left, and hold the end of the thread
with your left hand. Then, with your right hand, place
the bobbin in the bobbin case.
g
Lightly hold down the bobbin with your right hand
(1), and then guide the end of the thread around the
tab of the needle plate cover with your left hand (2).
1 Tab
h
While lightly holding down the bobbin with your right
hand (1), guide the thread through the slit in the
needle plate cover (2) and lightly pull it with your left
hand (3).
The thread enters the tension spring of the bobbin
case.
i
While lightly holding down the bobbin with your right
hand (1), continue guiding the thread through the slit
with your left hand (2) Then, cut the thread with the
cutter (3).
CAUTION
Be sure to hold down the bobbin with your
finger and unwind the bobbin thread
correctly, otherwise the thread may break or
the thread tension will be incorrect.
2
1
Memo
The order that the bobbin thread should be
passed through the bobbin case is indicated by
marks around the bobbin case. Be sure to thread
the machine as indicated.
Winding/Installing the Bobbin
B-18
j
Reattach the bobbin cover.
Insert the tab in the lower-left corner of the bobbin
cover, and then lightly press down on the right side.
The bobbin threading is finished.
Next, thread the upper thread. Continue with the
procedure in “Upper Threading” on page B-19.
k
Press to unlock all keys and buttons.
Note
If the thread is not correctly inserted through the
tension-adjusting spring of the bobbin case, it
may cause incorrect thread tension.
1 Tension-adjusting spring
Memo
You can begin sewing without pulling up the
bobbin thread. If you wish to pull up the bobbin
thread before starting to sew, pull up the thread
according to the procedure in “Pulling up the
bobbin thread” on page B-22.
1
1
2
Upper Threading
GETTING READY
Basic operations B-19
B
Threading the upper thread
a
Turn on the machine.
b
Raise the presser foot lever to raise the presser foot.
1 Presser foot lever
The upper thread shutter opens so the machine can
be threaded.
c
Press (Needle position button) once or twice to
raise the needle.
1 Needle position button
The needle is correctly raised when the mark on the
handwheel is at the top, as shown below. Check the
handwheel and, if this mark is not at this position, press
(Needle position button) until it is.
1 Mark on handwheel
d
Remove the spool cap that is inserted onto the spool
pin.
1 Spool pin
2 Spool cap
Upper Threading
CAUTION
Three spool cap sizes are available, allowing
you to choose a spool cap that best fits the size
of spool being used. If the spool cap is too
small for the spool being used, the thread may
catch on the slit in the spool or the needle may
break. For more information regarding the
choice of spool caps for your thread choice,
see page B-14.
When threading the upper thread, carefully
follow the instructions. If the upper threading
is not correct, the thread may become tangled
or the needle may bend or break.
Never use a thread weight of 20 or lower.
Use the needle and the thread in the correct
combination. For details on the correct
combination of needles and threads, refer to
“Fabric/thread/needle combinations” on
page B-26.
Note
If the presser foot is not raised, the machine
cannot be threaded.
1
1
1
1
2
Upper Threading
B-20
e
Place the spool of thread onto the spool pin.
Slide the spool onto the pin so that the spool is
horizontal and the thread unwinds to the front at the
bottom.
f
Slide the spool cap onto the spool pin.
Slide the spool cap as far as possible to the right, as
shown, with the rounded side on the left.
g
While holding the thread lightly with your right hand,
pull the thread with your left hand, and then pass the
thread behind the thread guide cover and to the front.
1 Thread guide cover
h
Pass the thread under the thread guide plate, and then
pull it up.
1 Thread guide plate
i
While using your right hand to lightly hold the thread
passed under the thread guide plate, pass the thread
through the guides in the order shown below.
j
Lower the presser foot.
k
Press .
If is pressed while the presser foot is raised, an
error message appears: “Lower the presser foot
lever.” or “Use the presser foot lifter button to lower
the presser foot.”
The screen changes, and all keys and operation
buttons are locked (except ).
CAUTION
If the spool or the spool cap is not positioned
correctly, the thread may become tangled
around the spool pin or the needle may break.
1
Note
If the presser foot has been lowered and the
shutter is closed, the machine cannot be
threaded. Be sure to raise the presser foot to
open the shutter before threading the machine.
In addition, before removing the upper thread, be
sure to raise the presser foot to open the shutter.
This machine is equipped with a window that
allows you to check the position of the take-up
lever. Look through this window and check that
the thread is correctly fed through the take-up
lever.
Upper Threading
GETTING READY
Basic operations B-21
B
l
Slide the thread behind the needle bar thread guide.
The thread can easily be slid behind the needle bar
thread guide by holding the thread in your left hand,
then feeding the thread with your right hand, as shown.
1 Needle bar thread guide
m
Raise the presser foot lever.
Threading the needle
a
Pull the end of the thread, which has been passed
through the needle bar thread guide, to the left, then
pass the thread through the notch of the threader
thread guide a, and then firmly pull the thread from
the front and insert it into the slit of the threader
thread guide disk marked “7” all the way b.
Make sure that the thread passes through the notch of
the threader thread guide.
1 Notch of the threader thread guide
2 Threader thread guide disk
b
Cut the thread with the cutter on the left side of the
machine.
1 Cutter
c
Lower the presser foot lever to lower the presser foot.
1 Presser foot lever
Memo
The needle threader can be used with machine
needles 75/11 through 100/16.
The needle threader cannot be used with the wing
needle or the twin needle.
When thread such as transparent nylon
monofilament or specialty threads are used it is
not recommended to use the needle threader.
If the needle threader cannot be used, refer to
“Threading the needle manually (without using the
needle threader)” on page B-22.
1
1
2
2
1
Note
If the thread is pulled through and cannot be cut
correctly, lower the presser foot lever so that the
thread is held in place before cutting the thread.
If this operation is performed, skip step
c.
When using thread that quickly winds off the
spool, such as metallic thread, it may be difficult
to thread the needle if the thread is cut.
Therefore, instead of using the thread cutter, pull
out about 80 mm (approx. 3 inches) of thread
after passing it through the threader thread guide
disks (marked “7”).
1 80 mm (approx. 3 inches) or more
1
1
1
Upper Threading
B-22
d
Lower the needle threader lever on the left side of the
machine until it clicks, and then slowly return the lever
to its original position.
1 Hook
2 Needle threader lever
The hook is rotated and passes the thread through the
eye of the needle.
e
Carefully pull the end of thread that was passed
through the eye of the needle.
If the needle was not completely threaded, but a loop in
the thread was formed in the eye of the needle, carefully
pull the loop through the eye of the needle to pull out
the end of the thread.
f
Raise the presser foot lever, pass the end of the thread
through and under the presser foot, and then pull out
about 5 cm (approx. 2 inches) of thread toward the
rear of the machine.
1 5 cm (approx. 2 inches)
g
Press to unlock all keys and buttons.
Threading the needle manually (without
using the needle threader)
When using specialty thread, such as transparent nylon
thread, a wing needle or a twin needle which cannot be used
with the needle threader, thread the needle as described
below.
a
Thread the machine to the needle bar thread guide.
For details, refer to “Upper Threading” on page B-19.
b
Lower the presser foot lever.
1 Presser foot lever
c
Insert the thread through the eye of the needle from
front to back.
d
Raise the presser foot lever, pass the end of the thread
through and under the presser foot, and then pull out
about 5 cm (approx. 2 inches) of thread toward the
rear of the machine.
e
Press to unlock all keys and buttons.
Pulling up the bobbin thread
When making gathers or before free motion quilting, first pull
up the bobbin thread as described below.
a
Refer to “Threading the upper thread” (page B-19) to
thread the machine with the upper thread and thread
the needle.
b
Follow steps d to f in “Installing the bobbin”
(page B-16) for installing the bobbin to insert the
bobbin into the bobbin case.
c
Pass the bobbin thread through the slot.
Do not cut the thread with the cutter.
Note
If the needle is not raised to its highest position,
the needle threader cannot thread the needle.
Turn the handwheel counterclockwise until the
needle is at its highest position. The needle is
correctly raised when the mark on the handwheel
is at the top, as shown under step
c on
page B-19.
CAUTION
When pulling out the thread, do not pull it
with extreme force, otherwise the needle may
break or bend.
1
1
Upper Threading
GETTING READY
Basic operations B-23
B
d
While lightly holding the upper thread with your left
hand, press (Needle position button) twice to raise
the needle.
The bobbin thread is looped around the upper thread
and can be pulled up.
e
Carefully pull the upper thread upward to pull out the
end of the bobbin thread.
f
Pull up the bobbin thread, pass it under the presser
foot and pull it about 10 cm (4 inches) toward the back
of the machine, making it even with the upper thread.
g
Reattach the bobbin cover.
Insert the tab in the lower-left corner of the bobbin
cover, and then lightly press down on the right side.
Using the twin needle
With the twin needle, you can sew two parallel lines of the
same stitch with two different threads. Both upper threads
should have the same thickness and quality. Be sure to use the
twin needle, the horizontal spool pin and the appropriate
spool cap.
For details on the stitches that can be sewn with the twin
needle, refer to “Stitch Setting Chart” beginning on page B-44.
a
Install the twin needle.
For details on installing a needle, refer to “Replacing
the needle” on page B-27.
b
Thread the upper thread for the left needle eye.
For details, refer to steps
a through l of
“Threading the upper thread” on page B-19.
c
Manually thread the left needle with the upper thread.
Pass the thread through the eye of the needle from the
front.
1
2
Memo
Traditionally a twin needle is also used for creating
pintucks. Contact your nearest authorized Baby
Lock retailer to obtain the optional pintuck foot for
your machine (ESG-PF).
CAUTION
Only use the twin needle (2.0/11 needle, part
code: X59296-121). Use of any other needle
may bend the needle or damage the machine.
Never use bent needles. Bent needles can
easily break, possibly resulting in injuries.
The needle threader cannot be used with the
twin needle. If the needle threader is used with
the twin needle, the machine may be
damaged.
Upper Threading
B-24
d
Insert the horizontal spool pin onto the bobbin winder
shaft.
Insert the horizontal spool pin so that it is perpendicular
to the bobbin winder shaft.
1 Bobbin winder shaft
e
Swing the spool pin toward the left so that it is
horizontal.
f
Place the upper thread spool for the needle on the right
side onto the horizontal spool pin, and then secure it
with the spool cap.
The thread should unroll from the top front of the spool.
1 Spool cap
2 Spool
g
Thread the upper thread in the same way that the
upper thread for the left side was threaded.
1 Thread guide cover
For details, refer to steps g through i of
“Threading the upper thread” on page B-19.
h
Without passing the thread through the needle bar
thread guide, manually thread the right needle.
Insert the thread through the eye of the needle from the
front.
The needle threader cannot be used with the twin
needle. If the needle threader is used with the twin
needle, the machine may be damaged.
i
Attach zigzag foot “J”.
For details on changing the presser foot, refer to
“Replacing the presser foot” on page B-29.
j
Turn on the machine and select a stitch.
For stitch selection see “Selecting a stitch pattern” on
page B-32.
See “Stitch Setting Chart” on page B-44 for stitches
that use a twin needle.
k
Select (Twin needle) in the settings screen.
l
Set the twin needle mode to “ON.”
m
Press .
1
12
1
CAUTION
When using the twin needle, be sure to attach
zigzag foot “J”. If bunched stitches occur, use
presser foot “N” or attach stabilizer material.
CAUTION
When using the twin needle, be sure to select
an appropriate stitch, otherwise the needle
may break or the machine may be damaged.
CAUTION
When using the twin needle, be sure to select
the twin needle setting, otherwise the needle
may break or the machine may be damaged.
Upper Threading
GETTING READY
Basic operations B-25
B
n
Start sewing.
For details on starting to sew, refer to “STARTING TO
SEW” on page B-31.
Two lines of stitching are sewn parallel to each other.
Note
When changing the sewing direction, press
(Needle position button) to raise the needle from
the fabric, and then raise the presser foot lever
and turn the fabric.
CAUTION
Do not try turning the fabric while the twin
needle is down in the fabric, otherwise the
needle may break or the machine may be
damaged.
Replacing the Needle
B-26
Be sure to observe the following precautions concerning the handling of the needle. Failure to observe these precautions is
extremely dangerous, for example, if the needle breaks and fragments are dispersed. Be sure to read and carefully follow the
instructions below.
Fabric/thread/needle combinations
The machine needle that should be used depends on the fabric and thread thickness. Refer to the following table when choosing
the thread and needle appropriate for the fabric that you wish to sew.
Thread and needle number
The lower the thread number is, the heavier the thread;
the higher the needle number, the larger the needle.
Ball point needle (gold colored)
To avoid skipped stitches use ball point needles (75/
11–90/14) with stretch fabrics.
Transparent nylon thread
Use a 90/14 to 100/16 needle, regardless of the fabric or
thread.
Replacing the Needle
CAUTION
Only use recommended home machine needles. Use of any other needle may bend the needle or damage
the machine.
Never use bent needles. Bent needles can easily break, possibly resulting in injuries.
Fabric Type/Application Thread Size of Needle
Type Size
Medium weight
fabrics
Broadcloth Cotton thread
60–90
75/11–90/14
Taffeta Synthetic thread
Flannel, Gabardine Silk thread 50
Thin fabrics Lawn Cotton thread
60–90
65/9–75/11
Georgette Synthetic thread
Challis, Satin Silk thread 50
Heavy fabrics Denim
Cotton thread
30 100/16
50
90/14–100/16
Corduroy Synthetic thread
50–60
Tweed Silk thread
Stretch fabrics Jersey
Thread for knits 50–60
Ball point needle
75/11–90/14
(gold colored)
Tric ot
Easily frayed fabrics
Cotton thread
50–90
65/9–90/14Synthetic thread
Silk thread 50
For top-stitching
Synthetic thread 30 100/16
Silk thread 50–90 90/11–90/14
Note
Never use thread of 20 weight or lower. It may
cause machine to malfunction.
CAUTION
The appropriate fabric, thread and needle
combinations are shown in the table above. If
the combination of the fabric, thread and
needle is not correct, particularly when sewing
heavy fabrics (such as denim) with thin
needles (such as 65/9 to 75/11), the needle
may bend or break. In addition, the stitching
may be uneven or puckered or there may be
skipped stitches.
Replacing the Needle
GETTING READY
Basic operations B-27
B
Checking the needle
Sewing with a bent needle is extremely dangerous since the
needle may break while the machine is being operated.
Before using the needle, place the flat side of the needle on a
flat surface and check that the distance between the needle
and the flat surface is even.
1 Flat side
2 Needle type marking
Replacing the needle
Use the screwdriver and a needle that has been determined to
be straight according to the instructions in “Checking the
needle”.
a
Press (Needle position button) once or twice to
raise the needle.
b
Place fabric or paper under the presser foot to cover
the hole in the needle plate.
c
Lower the presser foot.
d
Press .
If is pressed while the presser foot is raised, an
error message appears: “Lower the presser foot
lever.” or “Use the presser foot lifter button to lower
the presser foot.”
The screen changes, and all keys and operation
buttons are locked (except ).
e
Hold the needle with your left hand, and then use a
screwdriver to turn the needle clamp screw toward
you (counterclockwise) to remove the needle.
The needle clamp screw can also be loosened or
tightened with the L-shaped (or disc-shaped)
screwdriver.
1 Screwdriver
2 Needle clamp screw
Do not apply a strong force when loosening or
tightening the needle clamp screw, otherwise certain
parts of the machine may be damaged.
f
With the flat side of the needle toward the rear of the
machine, insert the needle until it touches the needle
stopper.
1 Needle stopper
CAUTION
If the distance between the needle and the flat
surface is not even, the needle is bent. Do not
use a bent needle.
1 Flat surface
Note
Before replacing the needle, cover the hole in the
needle plate with fabric or paper to prevent the
needle from falling into the machine.
1
2
1
1
2
1
1
Replacing the Needle
B-28
g
While holding the needle with your left hand, use the
screwdriver to tighten the needle clamp screw.
Turn the screw toward the back of the machine
(clockwise).
h
Press to unlock all keys and buttons.
CAUTION
Be sure to insert the needle until it touches the
needle stopper and securely tighten the needle
clamp screw with the screwdriver, otherwise
the needle may break or damage may result.
Replacing the Presser Foot
GETTING READY
Basic operations B-29
B
Replacing the presser foot
a
Press (Needle position button) once or twice to
raise the needle.
b
Lower the presser foot.
c
Press .
If is pressed while the presser foot is raised, an
error message appears: “Lower the presser foot
lever.” or “Use the presser foot lifter button to lower
the presser foot.”
The screen changes, and all keys and operation
buttons are locked (except ).
d
Raise the presser foot lever.
e
Press the black button at the back of the presser foot
holder.
1 Black button
2 Presser foot holder
f
Place a different presser foot below the holder so that
the presser foot pin is aligned with the notch in the
holder.
1 Presser foot holder
2 Notch
3 Pin
4 Presser foot type
g
Slowly lower the presser foot lever so that the presser
foot pin snaps into the notch in the presser foot holder.
1 Presser foot lever
2 Presser foot holder
3 Notch
4 Pin
The presser foot is attached.
h
Raise the presser foot lever to check that the presser
foot is securely attached.
1 Presser foot lever
i
Press to unlock all keys and buttons.
Replacing the Presser Foot
CAUTION
Use the presser foot appropriate for the type
of stitch that you wish to sew, otherwise the
needle may hit the presser foot, causing the
needle to bend or break.
Only use presser feet designed specifically for
this machine. Use of any other presser foot
may result in injuries or damage to the
machine.
a
b
1
2
3
4
J
2
3
4
1
1
Replacing the Presser Foot
B-30
Removing and attaching the presser foot
holder
Remove the presser foot holder when cleaning the machine or
when installing a presser foot that does not use the presser
foot holder, such as the walking foot and quilting foot. Use
the screwdriver to remove the presser foot holder.
a
Remove the presser foot.
For details, refer to “Replacing the presser foot” on
page B-29.
b
Use the screwdriver to loosen the presser foot holder
screw.
Turn the screw toward the back of the machine
(counterclockwise).
The presser foot holder screw can also be loosened
or tightened with the L-shaped (or disc-shaped)
screwdriver.
1 Screwdriver
2 Presser foot holder
3 Presser foot holder screw
Attaching the presser foot holder
a
Raise the presser foot lever.
b
Align the presser foot holder with the lower-left side of
the presser bar.
c
Hold the presser foot holder in place with your right
hand, and then tighten the screw using the screwdriver
in your left hand.
Turn the screw toward you (clockwise).
1 Screwdriver
Note
When a stitch is selected, the icon for the presser
foot that should be used appears in the screen.
Check that the correct presser foot is attached
before starting to sew. If the wrong presser foot
is installed, attach the correct presser foot.
Zigzag foot “J”
Monogramming foot “N”
Overcasting foot “G”
Buttonhole foot “A
Blind stitch foot “R”
Button fitting foot “M”
Side cutter “S”
For details on the presser foot that should be
used with the selected stitch, refer to “Stitch
Setting Chart” on page B-44.
13
2
CAUTION
Be sure to securely tighten the presser foot
holder screw, otherwise the presser foot
holder may fall off and the needle may strike
it, causing the needle to bend or break.
Note
If the presser foot holder is not correctly
installed, the thread tension will be incorrect.
1
Sewing
Basic operations B-31
STARTING TO SEW
B
Stitch selection methods
A stitch can be selected from the following methods available.
Stitch patterns can be selected through either direct select (by
pressing the designated key for a specific stitch) or number
selection (by entering the number for the stitch pattern).
For details on the types of stitches available, refer to the Quick
Reference Guide.
Direct selection
With direct selection, there are two stitch modes listed
below. Each press of switches the modes.
Preset utility stitch
Saved patterns
1 Preset utility stitch/saved pattern key
2 Numeric keys
Number selection
After pressing (Utility stitch key), (Decorative
stitch key) or (Character stitch key) to select the stitch
mode, use the numeric keys to type in the number for the
desired stitch.
1 Utility stitch key
2 Decorative stitch key
3 Character stitch key
4 Numeric keys
Utility stitches
There are various utility stitches, including straight
stitches, overcasting stitches and buttonhole stitches.
Decorative stitches
There are three decorative stitch modes: decorative stitch
1 mode , decorative stitch 2 mode and
decorative stitch 3 mode .
For details, refer to “Selecting stitch patterns” in the
“Decorative sewing” section.
Chapter 2
STARTING TO SEW
Sewing
CAUTION
While the machine is in operation, pay special
attention to the needle location. In addition,
keep your hands away from all moving parts
such as the needle and handwheel, otherwise
injuries may occur.
Do not pull or push the fabric too hard while
sewing, otherwise injuries may occur or the
needle may break.
Never use bent needles. Bent needles can
easily break, possibly resulting in injuries.
Make sure that the needle does not strike
basting pins, otherwise the needle may break
or bend.
The most frequently used utility stitches have been
assigned to the numeric keys.
These stitches can be selected simply by pressing
the designated key.
For details, refer to “Preset utility stitches” on
page B-50.
Frequently used patterns and combined patterns can
be saved on the machine’s memory and easily
retrieved using (Preset utility stitch/saved
pattern key) and the numeric keys. For details, refer
to “Saving a pattern” in the “Decorative sewing”
section.
1
2
1
2
3
4
Sewing
B-32
Character stitches
There are five character stitch modes: Gothic font mode
, Handwriting font mode , Outline font mode
, Cyrillic font mode and Japanese font mode
.
For details, refer to “Selecting stitch patterns” in the
“Decorative sewing” section.
Selecting a stitch pattern
When selecting a utility stitch
a
Press .
is displayed on the upper-left corner of the LCD
screen.
b
Enter the number of the desired stitch using numeric
keys.
For number of each stitch, refer to “Stitch Setting
Chart” on page B-44 or the Quick Reference Guide.
For stitches 01 through 09, the stitch can also be
selected by using the numeric keys to type in a one-
digit number, then pressing .
When using one-digit numbers and it is entered
incorrectly, press to erase the entered number.
The selected stitch is displayed on the LCD screen.
When selecting from the preset utility stitches
Since various stitches have been assigned to the numeric
keys, these stitches can be selected simply by pressing the
designated numeric key.
a
Check that appears in the upper-left corner of the
screen.
If a different icon is displayed, press .
b
Press the numeric key on which the desired stitch is
printed.
When selecting a character/decorative stitch
After pressing or on the operation panel the
necessary number of times, enter a number.
For more details, refer to “Selecting stitch patterns” in the
“Decorative sewing” section.
Sewing
Basic operations B-33
STARTING TO SEW
B
Sewing a stitch
a
Turn the main power to ON and push (Needle
position button) to raise the needle.
b
Select the desired stitch following the procedure
described in “Selecting a stitch pattern” above.
c
If necessary, specify the setting for automatic reverse/
reinforcement stitching and adjust the stitch length,
etc.
For details on adjusting the stitch width and length,
refer to “Setting the stitch width” on page B-37 and
“Setting the stitch length” on page B-37.
d
Install the presser foot.
For details on changing the presser foot, refer to
“Replacing the Presser Foot” on page B-29.
e
Set the fabric under the presser foot. Hold the fabric
and thread with your left hand, and rotate the
handwheel counterclockwise or press (needle
position button) to set the needle in the sewing start
position.
f
Lower the presser foot.
You do not have to pull up the bobbin thread.
g
Adjust the sewing speed with the sewing speed
controller.
You can use this controller to adjust sewing speed
during sewing.
1 Fast
2 Slow
h
Press the “Start/Stop” button to start sewing.
Guide the fabric lightly by hand.
i
Press the “Start/Stop” button again to stop sewing.
j
Press the (Thread cutter button) to trim the upper
and lower threads.
1 Thread cutter button
The needle will return to the up position
automatically.
Note
When a stitch is selected, the icon for the
presser foot that should be used appears on the
screen. Check that the correct presser foot is
attached before starting to sew. If the wrong
presser foot is installed, attach the correct
presser foot.
CAUTION
Always use the correct presser foot. If the
wrong presser foot is used, the needle may
strike the presser foot and bend or break,
possibly resulting in injury.
Refer to page B-44 for presser foot
recommendations.
Memo
The black button on the left side of presser foot
“J” should be pressed only if the fabric does not
feed or when sewing thick seams. For details,
refer to “Sewing thick fabrics” in the “Sewing”
section. Normally, you can sew without pressing
the black button.
Memo
When the foot controller is being used, you
cannot start sewing by pressing the “Start/Stop”
button.
b
a
1
Sewing
B-34
k
When the needle has stopped moving, raise the presser
foot and remove the fabric.
Using the foot controller
You can also use the foot controller to start and stop
sewing.
a
Turn off the machine.
b
Insert the foot controller plug into its jack on the
machine.
1 Foot controller jack
c
Turn on the machine.
d
Slowly depress the foot controller to start sewing.
e
Release the foot controller to stop the machine.
CAUTION
Do not press (Thread cutter button) after
the threads have been cut. Doing so could
tangle the thread or break the needle and
damage the machine.
Do not press (Thread cutter button) when
there is no fabric set in the machine or during
machine operation. The thread may tangle,
possibly resulting in damage.
Note
When cutting thread such as nylon monofilament
thread, or other decorative threads, use the
thread cutter on the side of the machine.
CAUTION
Do not allow fabric pieces and dust to collect
in the foot controller. Doing so could cause a
fire or an electric shock.
Memo
When the foot controller is being used, you
cannot start sewing by pressing the “Start/Stop”
button.
Bobbin winding can be started and stopped with
the foot controller.
Memo
The speed that is set using the sewing speed
controller will be the foot controller’s maximum
sewing speed.
1
Sewing
Basic operations B-35
STARTING TO SEW
B
Sewing reinforcement stitches
Reverse/reinforcement stitches are generally necessary at the
beginning and end of sewing. You can use (Reverse stitch
button) to sew reverse/reinforcement stitches (Refer to “Stitch
Setting Chart” under the column for “Reverse/ Reinforcement
stitching” on page B-44.).
While pressing
(Reinforcement stitch button), the machine
will sew 3 to 5 reinforcement stitches at that point and then
stop.
1 Reverse stitch button
2 Reinforcement stitch button
If the automatic reinforcement stitch is selected on the screen,
reverse stitches (or reinforcement stitches) will be sewn
automatically at the beginning of sewing when the “Start/
Stop” button is pressed. Press (Reverse stitch button) or
(Reinforcement stitch button) to sew reverse stitches or
reinforcement stitches automatically at the end of sewing.
1 Reverse stitch
2 Reinforcement stitch
The operation performed when the button is pressed differs
depending on the selected pattern. Refer to the table in
“Automatic reinforcement stitching” on page B-35.
Automatic reinforcement stitching
After selecting a stitch motif, turn on the automatic
reinforcement stitching function before sewing, and the
machine will automatically sew reinforcement stitches (or
reverse stitches, depending on the stitch motif) at the
beginning and end of sewing. Refer to the table on page B-36.
a
Select a stitch pattern.
b
Press to set the automatic reinforcement stitching
function.
The key will be lit.
c
Set the fabric in the start position and begin sewing.
1 Reverse stitches (or reinforcement stitches)
The machine will automatically sew reverse stitches
(or reinforcement stitches) and then continue sewing.
Memo
While pressing (Reinforcement stitch button)
when sewing character/decorative stitch pattern,
you can end sewing with a completed motif
instead of at the midpoint of a stitch motif.
The green light on the left of (Reinforcement
stitch button) lights up while the machine is
sewing a full motif, and it automatically turns off
when the sewing is stopped.
1 2
Memo
Some stitches, such as buttonholes and bar
tacks, require reinforcement stitches at the
beginning of sewing. If you select one of these
stitches, the machine will automatically turn on
this function (the key is lit when the stitch is
selected).
Memo
When selecting the stitches below, the machine
will automatically sew reverse stitches at the
beginning of the stitch.
If you press the “Start/Stop” button to pause
sewing, press it again to continue. The machine
will not sew reverse/reinforcement stitches again.
Sewing
B-36
d
Press (Reverse stitch button) or (Reinforcement
stitch button).
1 Reverse stitches (or reinforcement stitches)
The machine will sew reverse stitches (or
reinforcement stitches) and stop.
The operation performed when the button is pressed differs
depending on the selected pattern. Refer to the following table
for details on the operation that is performed when the button
is pressed.
* If (Reinforcement priority) in the settings
screen is set to “ON”, reinforcement stitches are
sewn instead of reverse stitches.
Memo
To turn off the automatic reinforcement stitching
function, press so that the key is no longer lit.
Reverse stitch
button
Reinforcement
stitch button
When the automatic
reinforcement
stitching function is
not active while
selecting utility
stitches like
examples shown
below
Machine starts
sewing the stitches
and only sews
reverse stitches
while holding the
Reverse stitch
button.
Machine starts
sewing the stitches
and sews 3 - 5
reinforcement
stitches while
holding the
Reinforcement stitch
button.
When the automatic
reinforcement
stitching function is
not active while
selecting utility
stitches like
examples shown
below
Machine starts
sewing the stitches
and only sews
reverse stitches
while holding the
Reverse stitch
button.*
Machine starts
sewing the stitches
and sews 3 - 5
reinforcement
stitches while
holding the
Reinforcement stitch
button.
When the automatic
reinforcement
stitching function is
active while selecting
utility stitches like
examples shown
below
Machine sews
reverse stitches at
the beginning and
end of sewing.
Machine sews
reverse stitches at
the beginning and
reinforcement
stitches at the end of
sewing.
When the automatic
reinforcement
stitching function is
active while selecting
utility stitches like
examples shown
below
Machine sews
reinforcement
stitches at the
beginning and
reverse stitches at
the end of sewing.*
Machine sews
reinforcement
stitches at the
beginning and end of
sewing.
When the automatic
reinforcement
stitching function is
not active while
selecting character/
decorative stitches
Machine starts
sewing and then
sews reinforcement
stitches while
holding the Reverse
stitch button.
Machine starts
sewing at the
beginning, then
completes the
pattern and sews
reinforcement
stitches at the end of
sewing.
When the automatic
reinforcement
stitching function is
active while selecting
character/decorative
stitches
Machine sews
reinforcement
stitches at the
beginning and sews
reinforcement
stitches when the
Reverse stitch
button is pressed.
Machine sews
reinforcement
stitches at the
beginning, then
completes the
pattern and sews
reinforcement
stitches at the end of
sewing.
Reverse stitch
button
Reinforcement
stitch button
Setting the Stitch
Basic operations B-37
STARTING TO SEW
B
This machine is preset with the default settings for the
stitch width and stitch length for each stitch. Some models
are also preset with the default settings for upper thread
tension for each stitch.
However, you can change their settings or adjust them by
following the procedure described in this section.
Setting the stitch width
The stitch width (zigzag width) can be adjusted to make the
stitch wider or narrower.
Each press of “-” makes the zigzag stitch narrower.
Each press of
“+” makes the zigzag stitch wider.
Setting the stitch length
The stitch length can be adjusted to make the stitch coarser
(longer) or finer (shorter).
Each press of “-”
makes the stitch finer (shorter).
Each press of
“+” makes the stitch coarser (longer).
Setting the Stitch
Note
Stitch settings return to their defaults if they are
changed, when the machine is turned off or a
different stitch is selected before the stitch
setting is saved, refer to “Saving stitch settings”
on page B-39.
Memo
Press to return the setting to its default.
If the straight stitch (left needle position or triple
stretch stitch) was selected, changing the stitch
width changes the needle position. Increasing the
width moves the needle to the right; reducing the
width moves the needle to the left.
means the setting cannot be adjusted.
CAUTION
After adjusting the stitch width, slowly turn
the handwheel toward you (counterclockwise)
and check that the needle does not touch the
presser foot. If the needle hits the presser foot,
the needle may bend or break.
Memo
Press to return the setting to its default.
means the setting cannot be adjusted.
Setting the Stitch
B-38
Setting the thread tension
You may need to change the thread tension, depending on the
fabric and thread being used.
Correct thread tension
The upper thread and the bobbin thread should cross near
the center of the fabric. Only the upper thread should be
visible from the right side of the fabric, and only the
bobbin thread should be visible from the wrong side of the
fabric.
1 Wrong side of fabric
2 Right side of fabric
3 Upper thread
4 Bobbin thread
Upper thread is too tight
If the bobbin thread is visible from the right side of the
fabric, the upper thread is too tight.
Loosen the thread tension.
1 Wrong side of fabric
2 Right side of fabric
3 Upper thread
4 Bobbin thread
5 The bobbin thread is visible from the right side of the
fabric.
Upper thread is too loose
If the upper thread is visible from the wrong side of the
fabric, the upper thread is too loose.
Tighten the thread tension.
1 Wrong side of fabric
2 Right side of fabric
3 Upper thread
4 Bobbin thread
5 The upper thread is visible from the wrong side of the
fabric.
Adjusting the thread tension
Using thread tension key (For models equipped with
thread tension key. Refer to page B-6)
Use the “-” and “+” keys.
Each time the “-” key is pressed less tension is applied.
Each time the “+” key is pressed more tension is applied.
Using thread tension dial (For models equipped with
thread tension dial. Refer to page B-6)
Pushing the thread tension dial toward the left makes the
thread tension looser.
Note
If the bobbin thread was incorrectly threaded, the
upper thread may be too tight. In this case, refer
to “Installing the bobbin” on page B-16 and
rethread the bobbin thread.
Note
If the upper thread was incorrectly threaded, the
upper thread may be too loose. In this case, refer
to “Upper Threading” on page B-19 and rethread
the upper thread.
1
2
3
4
1
2
3
4
5
Note
If the upper thread is not threaded correctly or
the bobbin is not installed correctly, it may not
be possible to set the correct thread tension. If
the correct thread tension cannot be achieved,
rethread the upper thread and insert the bobbin
correctly.
Memo
Press to return the setting to its default.
5
1
2
3
4
Setting the Stitch
Basic operations B-39
STARTING TO SEW
B
Pushing the thread tension dial toward the right makes the
thread tension tighter.
Saving stitch settings
If you wish to save specific settings for a stitch so that they can
be used later, press after changing the settings to save the
new settings with the selected stitch.
This feature can be used only with utility stitches.
To use a stitch length of 2.0 mm for the straight stitch
a
Select a straight stitch.
b
Set the stitch length to 2.0 mm.
c
Press .
To reset the selected stitch pattern back to its default
settings, press , and then press .
Note
The next time that the same straight stitch is
selected, the stitch length is set to 2.0 mm.
Both of the stitch width (zigzag width) and stitch
length are saved, not just the setting that was
changed. With models equipped with the thread
tension keys, the setting for upper thread tension
is also saved, even if it was not changed. When
the same stitch pattern is selected, the last
settings saved are displayed even if the machine
was turned off. If the settings are changed again,
or if is pressed to reset the setting to its
default, the new settings are not saved unless
is pressed another time.
Even if is pressed, the settings for
programmed thread cutting and automatic
reverse/reinforcement stitching cannot be reset.
Useful Functions
B-40
Automatically cutting the thread
The machine can be set to automatically cut the threads at the
end of the stitching. This is called “programmed thread-
cutting”. If programmed thread-cutting is set, automatic
reverse/reinforcement stitching is also set.
a
Turn on the machine.
b
Select a stitch.
For details on selecting a stitch, refer to “Selecting a
stitch pattern” on page B-32.
c
Press .
and are lit, and the machine is set for
programmed thread-cutting and automatic reverse/
reinforcement stitching.
To turn programmed thread cutting off, press .
d
Set the fabric in place, and press the “Start/Stop
button once.
Stitching will begin after reverse stitches or
reinforcement stitches are sewn.
e
Once you have reached the end of the stitching, press
(Reverse stitch button) or (Reinforcement stitch
button) once.
If stitching, such as buttonholes and bar tacking, that
includes reinforcement stitching has been selected, this
operation is unnecessary.
After the reverse stitching or reinforcement stitching
has been done, the machine stops, and the thread is
cut.
1 The point where the “Start/Stop” button was pressed.
2 The point where (Reverse stitch button) or
(Reinforcement stitch button) was pressed.
3 The thread is cut here.
Mirroring stitches
You can sew the mirror image of a stitch horizontally (left and
right).
a
Turn on the machine.
b
Select a stitch.
For details on selecting a stitch, refer to “Selecting a
stitch pattern” on page B-32.
c
Press .
is displayed on the screen, and the pattern
displayed on the screen is mirrored.
To turn the mirrored stitching off, press again.
Useful Functions
32
1
Memo
Programmed thread-cutting will not be performed
if the “Start/Stop” button is pressed while sewing.
Press (Reverse stitch button) or
(Reinforcement stitch button) at the end of the
stitching.
If the power is turned off, programmed thread-
cutting will be turned off.
Useful Functions
Basic operations B-41
STARTING TO SEW
B
Adjusting the presser foot pressure
You can adjust the presser foot pressure (the amount of
pressure applied to the fabric by the presser foot) on the
settings screen. The higher the number, the greater the
pressure will be. Set the pressure at “3” for normal sewing.
a
Select (Presser foot pressure) in the settings
screen.
b
Adjust the pressure by pressing the “-” or “+” key.
Automatic Fabric Sensor System (Automatic
presser foot pressure)
(For models equipped with automatic fabric
sensor system. Refer to page B-6)
The thickness of the fabric is automatically detected and the
presser foot pressure is automatically adjusted with an internal
sensor while sewing, to insure that your fabric is fed smoothly.
The fabric sensor system works continuously while sewing.
This function is useful for sewing over thick seams or quilting.
For details, refer to the “Sewing” section.
a
Select (Automatic fabric sensor system) in the
settings screen.
b
Set the sensor system to “ON” by pressing the “-” or
“+” key.
Pivoting
(For models equipped with pivot function.
Refer to page B-6)
If the pivot key is selected, the machine stops with the needle
lowered (in the fabric) and the presser foot is automatically
raised to an appropriate height when the “Start/Stop” button is
pressed. When the “Start/Stop” button is pressed again, the
presser foot is automatically lowered and sewing continues.
This function is useful for stopping the machine to rotate the
fabric.
Memo
Depending on the selected stitch, mirroring may
not be possible; for example, buttonhole stitch.
When the machine is turned off, the mirroring
setting is cancelled.
CAUTION
When the pivot key is selected, the machine
will begin stitching when the “Start/Stop”
button is pressed or the foot controller is
pressed down even if the presser foot has been
raised by pressing (presser foot lifter
button). Be sure to keep your hands and other
items away from the needle, otherwise injuries
may occur.
Memo
When the pivot key is selected, the height of the
presser foot when sewing is stopped can be
changed according to the type of fabric being
sewn. Select (Pivoting height) in the settings
screen. Press the “-” or “+” key to select one of
the three heights (3.2 mm, 5.0 mm or 7.5 mm).
Generally 3.2 mm is the preferred setting.
Useful Functions
B-42
a
Select a stitch.
b
Press to select the pivot function.
The key will be lit.
c
Place the fabric under the presser foot with the needle
at the starting point of the stitching, lower the presser
foot and then press the “Start/Stop” button. The
machine will begin sewing.
d
Press the “Start/Stop” button to stop the machine at
the point where the sewing direction changes.
The machine stops with the needle in the fabric, and
the presser foot is raised.
e
Rotate the fabric, and then press the “Start/Stop”
button.
The presser foot is automatically lowered, and
sewing continues.
Sewing with free motion mode
(For models equipped with free motion mode.
Refer to page B-6)
With free motion mode, the presser foot is raised to the
necessary height for free motion sewing. When starting to
sew, the internal sensor detects the thickness of the fabric, and
the quilting foot is raised to the height specified in the
machine settings screen.
In free motion mode, lower the feed dogs (using the feed dog
position switch) so that the fabric can be moved freely in any
direction.
Setting the machine to free motion mode
a
Select a stitch pattern.
b
Select (Free motion) in the settings screen.
c
Set the free motion mode to “ON” by pressing the “-”
or “+” key.
Note
(Needle position) in the settings screen, must
be set to the down position
for the pivot function
to be used. When (Needle position) is set in
the raised position, cannot be used. The
pivot function can only be used with stitches
where presser foot J or N is indicated on the
screen. If any other stitch is selected, is not
available.
Use (Presser foot lifter button) to make sure
the presser foot is lowered, and then press the
“Start/Stop” button to continue sewing.
If the pivot key is selected, (Presser foot
height) setting in the settings screen can not be
changed.
Memo
If you press the “Start/Stop” button to pause
sewing, press it again to continue, reverse
stitches (or reinforcement stitches) will not be
sewn.
Useful Functions
Basic operations B-43
STARTING TO SEW
B
Adjusting free motion presser foot height
a
Select (Free motion foot height) in the settings
screen.
b
Adjust the height that the quilting foot is raised above
the fabric by pressing the “-” or “+” key.
Increase the setting by pressing “+”, for example,
when sewing very stretchy fabric, so that it is easier
to sew.
Hands-free raising and lifting of the presser
foot
Using the knee lifter, you can raise and lower the presser foot
with your knee, leaving both hands free to handle the fabric.
Installing the knee lifter
a
Turn off the machine.
b
Insert the knee lifter into the mounting slot on the front
of the machine in the lower-right corner.
Align the tabs on the knee lifter with the notches in the
mounting slot, and then insert the knee lifter as far as
possible.
Using the knee lifter
a
Stop the machine.
Do not use the knee lifter while the machine is
operating.
b
With your knee, press the knee lifter to the right.
Keep the knee lifter pressed to the right.
The presser foot is raised.
c
Release the knee lifter.
The presser foot is lowered.
CAUTION
With free motion quilting, control the feeding
speed of the fabric to match the sewing speed.
If the fabric is moved faster than the sewing
speed, the needle may break or other damage
may result.
Memo
In order to sew with a balanced tension, it may be
necessary to adjust the upper thread tension. For
details, refer to “Setting the thread tension” on
page B-38. Test with a sample piece of quilting
fabric.
Note
If the knee lifter is not fully inserted into the
mounting slot, it may fall out while the machine is
operating.
CAUTION
While sewing, keep your knee away from the
knee lifter. If the knee lifter is pressed while
the machine is operating, the needle may
break or the machine may be damaged.
Stitch Setting Chart
B-44
Applications, stitch lengths and widths and whether the twin needle can be used are listed for utility stitches in the
following table.
*1
Patterns printed on the numeric keys on the machine can be selected directly. For details, refer to “Preset utility stitches” on
page B-50.
*2
For free motion quilting, use free motion open toe quilting foot “O” (sold separately with some models).
*3
When (Automatic reverse/reinforcement key) is activated, the stitch will begin with reinforcement stitch.
If (Reinforcement priority) on the settings screen is also set to “ON”, the machine will sew reinforcement stitches at the
end of stitching and then stop.
*4
For free motion quilting, use free motion quilting foot “C” (sold separately with some models) or free motion open toe quilting
foot “O” (sold separately with some models).
*5
Do not sew reverse stitching when using the walking foot.
Stitch Setting Chart
Stitch Stitch name
Presser
foot
Applications
Stitch width
[mm (inch)]
Stitch length
[mm (inch)]
Twin
needle
Reverse/
Reinforce-
ment
stitching
Walking
foot
BLMSP/BLMLR
BL210A
Auto.
Manual
Auto.
Manual
Stitch
number
01
*1
01
*1
Straight stitch
(Left)
J
*2
General sewing,
gather, pintuck, etc.
0.0 (0)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.2 - 5.0
(1/64 - 3/16)
OK
( J )
Reverse
OK
*5
02
*1
02
*1
Straight stitch
(Left)
J
*2
General sewing,
gather, pintuck, etc.
0.0 (0)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.2 - 5.0
(1/64 - 3/16)
OK
( J )
Reverse
*3
OK
*5
03
*1
03
*1
Straight stitch
(Middle)
J
*2
General sewing,
gather, pintuck, etc.
3.5 (1/8)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.2 - 5.0
(1/64 - 3/16)
OK
( J )
Reverse
OK
*5
04
*1
04
*1
Straight stitch
(Middle)
J
*2
General sewing,
gather, pintuck, etc.
3.5 (1/8)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.2 - 5.0
(1/64 - 3/16)
OK
( J )
Reverse
*3
OK
*5
05
*1
05
*1
Triple stretch
stitch
J
*2
General sewing for
reinforcement and
decorative
topstitching
0.0 (0)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
06
*1
06
*1
Stem stitch
J
*2
Reinforced stitching,
sewing and decorative
applications
1.0 (1/16)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
07 -
Decorative
stitch
N
*2
Decorative stitching,
top stitching
0.0 (0)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
08 07
Basting stitch
J
*2
Basting
0.0 (0)
0.0 - 7.0
(0 - 1/4)
BLMSP/
BLMLR:
20 (3/4)
5 - 30
(3/16 - 1-3/16)
BL210A:
NO
Reinforce-
ment
NO
09
*1
08
*1
Zigzag stitch
J
*2
For overcasting,
mending.
3.5 (1/8)
0.0 - 7.0
(0 - 1/4)
1.4 (1/16)
0.0 - 5.0
(0 - 3/16)
OK
( J )
Reverse
OK
*5
10
*1
09
*1
Zigzag stitch
J
*2
For overcasting,
mending.
3.5 (1/8)
0.0 - 7.0
(0 - 1/4)
1.4 (1/16)
0.0 - 5.0
(0 - 3/16)
OK
( J )
Reverse
*3
OK
*5
11 10
Zigzag stitch
(Right)
J
*2
Start from right needle
position, zigzag sew at
left.
3.5 (1/8)
2.5 - 5.0
(3/32 - 3/16)
1.4 (1/16)
0.3 - 5.0
(1/64 - 3/16)
OK
( J )
Reverse
*3
OK
*5
12 -
Zigzag stitch
(Left)
J
*2
Start from left needle
position, zigzag sew at
right.
3.5 (1/8)
2.5 - 5.0
(3/32 - 3/16)
1.4 (1/16)
0.3 - 5.0
(1/64 - 3/16)
OK
( J )
Reverse
*3
OK
*5
Stitch Setting Chart
Basic operations B-45
STARTING TO SEW
B
13 11
2 steps elastic
zigzag stitch
J
*2
Overcasting (medium
weight and stretch
fabrics), tape and
elastic
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
1.0 (1/16)
0.2 - 5.0
(1/64 - 3/16)
OK
( J )
Reverse
*3
OK
*5
14
*1
12
*1
3 steps elastic
zigzag stitch
J
*2
Overcasting (medium,
heavyweight and
stretch fabrics), tape
and elastic
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
1.0 (1/16)
0.2 - 5.0
(1/64 - 3/16)
OK
( J )
Reverse
*3
OK
*5
15
*1
13
*1
Overcasting
stitch G
Reinforcing of light
and medium weight
fabrics
3.5 (1/8)
2.5 - 5.0
(3/32 - 3/16)
2.0 (1/16)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
16 14
Overcasting
stitch G
Reinforcing of
heavyweight fabric
5.0 (3/16)
2.5 - 5.0
(3/32 - 3/16)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
17 15
Overcasting
stitch
G
Reinforcing of
medium, heavyweight
and easily friable
fabrics or decorative
stitching.
5.0 (3/16)
3.5 - 5.0
(1/8 - 3/16)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
18 16
Overcasting
stitch
J
*2
Reinforced seaming of
stretch fabric
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
19 17
Overcasting
stitch
J
*2
Reinforcing of medium
stretch fabric and
heavyweight fabric,
decorative stitching
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
20 18
Overcasting
stitch
J
*2
Reinforcement of
stretch fabric or
decorative stitching
4.0 (3/16)
0.0 - 7.0
(0 - 1/4)
4.0 (3/16)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
21 19
Overcasting
stitch
J
*2
Stretch knit seam 5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
4.0 (3/16)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
22 -
Single
diamond
overcast stitch
J
*2
Reinforcement and
seaming stretch fabric
6.0 (15/64)
0.0 - 7.0
(0 - 1/4)
3.0 (1/8)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
23 -
Single
diamond
overcast stitch
J
*2
Reinforcement of
stretch fabric
6.0 (15/64)
0.0 - 7.0
(0 - 1/4)
1.8 (1/16)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
24 20
With side
cutter S
Straight stitch while
cutting fabrics
0.0 (0)
0.0 - 2.5
(0 - 3/32)
2.5 (3/32)
0.2 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
25 21
With side
cutter S
Zigzag stitch while
cutting fabrics
3.5 (1/8)
3.5 - 5.0
(1/8 - 3/16)
1.4 (1/16)
0.0 - 5.0
(0 - 3/16)
NO
Reinforce-
ment
NO
26 22
With side
cutter S
Overcasting stitch
while cutting fabrics
3.5 (1/8)
3.5 - 5.0
(1/8 - 3/16)
2.0 (1/16)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
27 23
With side
cutter S
Overcasting stitch
while cutting fabrics
5.0 (3/16)
3.5 - 5.0
(1/8 - 3/16)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
28 24
With side
cutter S
Overcasting stitch
while cutting fabrics
5.0 (3/16)
3.5 - 5.0
(1/8 - 3/16)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
29 25
Piecing stitch
(Right)
J
*2
Piecework/patchwork
6.5 mm (approx. 1/4
inch) right seam
allowance
5.5 (7/32)
0.0 - 7.0
(0 - 1/4)
2.0 (1/16)
0.2 - 5.0
(1/64 - 3/16)
NO
Reverse
*3
OK
*5
30 26
Piecing stitch
(Middle)
J
*4
Piecework/patchwork
2.0 (1/16)
0.2 - 5.0
(1/64 - 3/16)
NO
Reverse
*3
OK
*5
Stitch Stitch name
Presser
foot
Applications
Stitch width
[mm (inch)]
Stitch length
[mm (inch)]
Twin
needle
Reverse/
Reinforce-
ment
stitching
Walking
foot
BLMSP/BLMLR
BL210A
Auto.
Manual
Auto.
Manual
Stitch
number
Stitch Setting Chart
B-46
31 -
Piecing stitch
(Left)
J
*2
Piecework/patchwork
6.5 mm (approx. 1/4
inch) left seam
allowance
1.5 (1/16)
0.0 - 7.0
(0 - 1/4)
2.0 (1/16)
0.2 - 5.0
(1/64 - 3/16)
NO
Reverse
*3
OK
*5
32 27
Hand-look
quilting stitch
J
*2
Quilting stitch made to
look like hand quilting
stitch
0.0 (0)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
33 28
Quilting
appliq
zigzag stitch
J
*2
Zigzag stitch for
quilting and sewing on
appliqué quilt pieces
3.5 (1/8)
0.0 - 7.0
(0 - 1/4)
1.4 (1/16)
0.0 - 5.0
(0 - 3/16)
NO
Reverse
*3
OK
*5
34 29
Quilting
appliqué stitch
J
*2
Quilting stitch for
invisible appliqué or
attaching binding
1.5 (1/16)
0.0 - 7.0
(0 - 1/4)
1.8 (1/16)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
35 30
Quilting
stippling stitch
J
*2
Background quilting 7.0 (1/4)
0.0 - 7.0
(0 - 1/4)
1.6 (1/16)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
36 31
Blind hem
stitch R
Hemming woven
fabrics
00
3 - 3
2.0 (1/16)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
37 32
Blind hem
stretch stitch R
Hemming stretch
fabric
00
3 - 3
2.0 (1/16)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
38 33
Blanket stitch
J
Appliqués, decorative
blanket stitch
3.5 (1/8)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
39 34
Shell tuck
edge stitch
J
*2
Shell tuck edge finish
on fabrics
4.0 (3/16)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.2 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
40 35
Satin scallop
stitch
N
*2
Decorating collar of
blouse, edge of
handkerchief
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
0.5 (1/32)
0.1 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
41 -
Scallop stitch
N
*2
Decorating collar of
blouse, edge of
handkerchief
7.0 (1/4)
0.0 - 7.0
(0 - 1/4)
1.4 (1/16)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
42 36
Patchwork join
stitch
J
*2
Patchwork stitches,
decorative stitching
4.0 (3/16)
0.0 - 7.0
(0 - 1/4)
1.2 (1/16)
0.2 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
43 37
Patchwork
double
overlock stitch
J
*2
Patchwork stitches,
decorative stitching
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
44 38
Couching
stitch
J
*2
Decorative stitching,
attaching cord and
couching
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
1.2 (1/16)
0.2 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
45 39
Smocking
stitch
J
*2
Smocking, decorative
stitching
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
1.6 (1/16)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
46 40
Feather stitch
J
*2
Fagoting, decorative
stitching
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
47 41
Fagoting cross
stitch
J
*2
Fagoting, bridging and
decorative stitching
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
48 42
Tape attaching
stitch
J
*2
Attaching tape to
seam in stretch fabric
4.0 (3/16)
0.0 - 7.0
(0 - 1/4)
1.0 (1/16)
0.2 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
49 43
Ladder stitch
J
*2
Decorative stitching 4.0 (3/16)
0.0 - 7.0
(0 - 1/4)
3.0 (1/8)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
Stitch Stitch name
Presser
foot
Applications
Stitch width
[mm (inch)]
Stitch length
[mm (inch)]
Twin
needle
Reverse/
Reinforce-
ment
stitching
Walking
foot
BLMSP/BLMLR
BL210A
Auto.
Manual
Auto.
Manual
Stitch
number
Stitch Setting Chart
Basic operations B-47
STARTING TO SEW
B
50 44
Rick-rack
stitch
J
*2
Decorative top
stitching
4.0 (3/16)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
51 45
Decorative
stitch
J
*2
Decorative stitching 5.5 (7/32)
0.0 - 7.0
(0 - 1/4)
1.6 (1/16)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
52 46
Serpentine
stitch
N
*2
Decorative stitching
and attaching elastic
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
1.0 (1/16)
0.2 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
53 -
Decorative
stitch
N
*2
Decorative stitching
and appliqué
6.0 (15/64)
0.0 - 7.0
(0 - 1/4)
1.0 (1/16)
0.2 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
54 -
Decorative
stippling stitch
N
*2
Decorative stitching 7.0 (1/4)
0.0 - 7.0
(0 - 1/4)
1.6 (1/16)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
55 -
Hemstitching
N
*2
Decorative hems,
triple straight at left
1.0 (1/16)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
56 -
Hemstitching
N
*2
Decorative hems,
triple straight at center
3.5 (1/8)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
57 47
Hemstitching
zigzag
N
*2
Decorative hems, top
stitching
6.0 (15/64)
0.0 - 7.0
(0 - 1/4)
3.0 (1/8)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
58 48
Hemstitching
N
*2
Decorative hems, lace
attaching pin stitch
3.5 (1/8)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
59 49
Hemstitching
N
*2
Decorative hems 3.0 (1/8)
0.0 - 7.0
(0 - 1/4)
3.5 (1/8)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
60 50
Hemstitching
N
*2
Decorative hems daisy
stitch
6.0 (15/64)
0.0 - 7.0
(0 - 1/4)
3.0 (1/8)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
61 -
Hemstitching
N
*2
Heirloom, decorative
hems
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
3.5 (1/8)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
62 51
Hemstitching
N
*2
Heirloom, decorative
hems
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
3.5 (1/8)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
63 -
Hemstitching
N
*2
Heirloom, decorative
hems
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
3.5 (1/8)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
64 52
Hemstitching
N
*2
Heirloom, decorative
hems
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
4.0 (3/16)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
65 -
Hemstitching
N
*2
Heirloom, decorative
hems
4.0 (3/16)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
66 -
Honeycomb
stitch
N
*2
Heirloom, decorative
hems
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
67 -
Honeycomb
stitch
N
*2
Heirloom, decorative
hems
6.0 (15/64)
0.0 - 7.0
(0 - 1/4)
3.5 (1/8)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
68 53
Hemstitching
N
*2
Heirloom, decorative
hems
6.0 (15/64)
0.0 - 7.0
(0 - 1/4)
1.6 (1/16)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
Stitch Stitch name
Presser
foot
Applications
Stitch width
[mm (inch)]
Stitch length
[mm (inch)]
Twin
needle
Reverse/
Reinforce-
ment
stitching
Walking
foot
BLMSP/BLMLR
BL210A
Auto.
Manual
Auto.
Manual
Stitch
number
Stitch Setting Chart
B-48
69 54
Hemstitching
N
*2
Heirloom, decorative
hems
6.0 (15/64)
0.0 - 7.0
(0 - 1/4)
3.0 (1/8)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
70 -
Hemstitching
N
*2
Heirloom, decorative
hems
6.0 (15/64)
0.0 - 7.0
(0 - 1/4)
4.0 (3/16)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
71 55
Hemstitching
N
*2
Heirloom, decorative
hems
4.0 (3/16)
0.0 - 7.0
(0 - 1/4)
2.5 (3/32)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
72 56
Hemstitching
N
*2
Heirloom, decorative
hems
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
2.0 (1/16)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
73 -
Hemstitching
N
*2
Decorative hems and
bridging stitch
6.0 (15/64)
0.0 - 7.0
(0 - 1/4)
2.0 (1/16)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
74 -
Hemstitching
N
*2
Decorative hems.
Fagoting, attaching
ribbon
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
3.0 (1/8)
0.4 - 5.0
(1/64 - 3/16)
OK
( J )
Reinforce-
ment
NO
75 -
Hemstitching
N
*2
Decorative hems,
smocking
6.0 (15/64)
0.0 - 7.0
(0 - 1/4)
1.6 (1/16)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
76 -
Hemstitching
N
*2
Decorative hems,
smocking
5.0 (3/16)
0.0 - 7.0
(0 - 1/4)
1.6 (1/16)
0.4 - 5.0
(1/64 - 3/16)
NO
Reinforce-
ment
NO
77 57
Narrow
rounded
buttonhole
stitch
A
Buttonhole on light to
medium weight fabrics
5.0 (3/16)
3.0 - 5.0
(1/8 - 3/16)
0.4 (1/64)
0.2 - 1.0
(1/64 - 1/16)
NO
Automatic
reinforce-
ment
NO
78 58
Tapered round
ended
buttonhole
stitch
A
Reinforced waist
tapered buttonholes
5.0 (3/16)
3.0 - 5.0
(1/8 - 3/16)
0.4 (1/64)
0.2 - 1.0
(1/64 - 1/16)
NO
Automatic
reinforce-
ment
NO
79 59
Round ended
buttonhole
stitch
A
Buttonholes with
vertical bar tack in
heavyweight fabrics
5.0 (3/16)
3.0 - 5.0
(1/8 - 3/16)
0.4 (1/64)
0.2 - 1.0
(1/64 - 1/16)
NO
Automatic
reinforce-
ment
NO
80 60
Narrow
squared
buttonhole
stitch
A
Buttonholes for light to
medium weight fabrics
5.0 (3/16)
3.0 - 5.0
(1/8 - 3/16)
0.4 (1/64)
0.2 - 1.0
(1/64 - 1/16)
NO
Automatic
reinforce-
ment
NO
81 61
Stretch
buttonhole
stitch
A
Buttonholes for
stretch or woven
fabrics
6.0 (15/64)
3.0 - 6.0
(1/8 - 15/64)
1.0 (1/16)
0.5 - 2.0
(1/32 - 1/16)
NO
Automatic
reinforce-
ment
NO
82 62
Heirloom
buttonhole
stitch
A
Buttonholes for
heirloom and stretch
fabrics
6.0 (15/64)
3.0 - 6.0
(1/8 - 15/64)
1.5 (1/16)
1.0 - 3.0
(1/16 - 1/8)
NO
Automatic
reinforce-
ment
NO
83 63
Bound
buttonhole
stitch
A
The first step in
making bound
buttonholes
5.0 (3/16)
0.0 - 6.0
(0 - 15/64)
2.0 (1/16)
0.2 - 4.0
(1/64 - 3/16)
NO
Automatic
reinforce-
ment
NO
84 64
Keyhole
buttonhole
stitch
A
Buttonholes in
heavyweight or thick
fabrics for larger flat
buttons
7.0 (1/4)
3.0 - 7.0
(1/8 - 1/4)
0.5 (1/32)
0.3 - 1.0
(1/64 - 1/16)
NO
Automatic
reinforce-
ment
NO
85 65
Tapered
keyhole
buttonhole
stitch
A
Buttonholes in
medium to heavy
weight fabrics for
larger flat buttons
7.0 (1/4)
3.0 - 7.0
(1/8 - 1/4)
0.5 (1/32)
0.3 - 1.0
(1/64 - 1/16)
NO
Automatic
reinforce-
ment
NO
Stitch Stitch name
Presser
foot
Applications
Stitch width
[mm (inch)]
Stitch length
[mm (inch)]
Twin
needle
Reverse/
Reinforce-
ment
stitching
Walking
foot
BLMSP/BLMLR
BL210A
Auto.
Manual
Auto.
Manual
Stitch
number
Stitch Setting Chart
Basic operations B-49
STARTING TO SEW
B
86 66
Keyhole
buttonhole
stitch A
Buttonholes with
vertical bar tack for
reinforcement in
heavyweight or thick
fabrics
7.0 (1/4)
3.0 - 7.0
(1/8 - 1/4)
0.5 (1/32)
0.3 - 1.0
(1/64 - 1/16)
NO
Automatic
reinforce-
ment
NO
87 67
Darning stitch
A
Darning of medium
weight fabric
7.0 (1/4)
2.5 - 7.0
(3/32 - 1/4)
2.0 (1/16)
0.4 - 2.5
(1/64 - 3/32)
NO
Automatic
reinforce-
ment
NO
88 68
Darning stitch
A
Darning of
heavyweight fabric
7.0 (1/4)
2.5 - 7.0
(3/32 - 1/4)
2.0 (1/16)
0.4 - 2.5
(1/64 - 3/32)
NO
Automatic
reinforce-
ment
NO
89 69
Bar tack stitch
A
Reinforcement at
opening of pocket,
etc.
2.0 (1/16)
1.0 - 3.0
(1/16 - 1/8)
0.4 (1/64)
0.3 - 1.0
(1/64 - 1/16)
NO
Automatic
reinforce-
ment
NO
90 70
Button sewing
stitch M
Attaching buttons 3.5 (1/8)
2.5 - 4.5
(3/32 - 3/16)
NO
Reinforce-
ment
NO
91 71
Eyelet stitch
N
For making eyelets,
holes on belts, etc.
7.0 (1/4)
7.0 6.0 5.0
(1/4 15/64
3/16)
7.0 (1/4)
7.0 6.0 5.0
(1/4 15/64
3/16)
NO
Automatic
reinforce-
ment
NO
92 -
Reverse
(Straight
stitch)
N
For attaching appliqué
on tubular pieces of
fabric and mitering
corners
——NO
Reinforce-
ment
NO
93 -
Sideways to
left (Straight
stitch)
N
For attaching appliqué
on tubular pieces of
fabric
——NO
Reinforce-
ment
NO
94 -
Sideways to
right (Straight
stitch)
N
For attaching appliqué
on tubular pieces of
fabric
——NO
Reinforce-
ment
NO
95 -
Forward
(Straight
stitch)
N
For attaching appliqué
on tubular pieces of
fabric and mitering
corners
——NO
Reinforce-
ment
NO
96 -
Sideways to
left (Zigzag
stitch)
N
For attaching appliqué
on tubular pieces of
fabric
——NO
Reinforce-
ment
NO
97 -
Sideways to
right (Zigzag
stitch)
N
For attaching appliqué
on tubular pieces of
fabric
——NO
Reinforce-
ment
NO
98 -
Forward
(Zigzag stitch)
N
For attaching appliqué
on tubular pieces of
fabric and mitering
corners
——NO
Reinforce-
ment
NO
99 -
Reverse
(Zigzag stitch)
N
For attaching appliqué
on tubular pieces of
fabric and mitering
corners
——NO
Reinforce-
ment
NO
Stitch Stitch name
Presser
foot
Applications
Stitch width
[mm (inch)]
Stitch length
[mm (inch)]
Twin
needle
Reverse/
Reinforce-
ment
stitching
Walking
foot
BLMSP/BLMLR
BL210A
Auto.
Manual
Auto.
Manual
Stitch
number
Stitch Setting Chart
B-50
Preset utility stitches
The most frequently used utility stitches have been
assigned to the numeric keys.
These stitches can be selected simply by pressing the
designated key while in the preset utility stitch mode.
Stitch name
Preset utility
stitches
BLMSP/BLMLR
BL210A
Stitch number
Straight stitch (Left)
01 01
Straight stitch (Left)
02 02
Straight stitch (Middle)
03 03
Straight stitch (Middle)
04 04
Zigzag stitch
09 08
Zigzag stitch
10 09
Triple stretch stitch
05 05
Stem stitch
06 06
Overcasting stitch
15 13
3 steps elastic zigzag
stitch
14 12
Sewing
This section describes procedures for using the various utility stitches as well as other
functions. It provides details on basic sewing in addition to the more expressive features of
the machine, such as sewing tubular pieces and buttonholes.
Page number starts with “S” in this section.
Chapter1 SEWING ATTRACTIVE FINISHES......................... S-2
Chapter2 UTILITY STITCHES................................................... S-6
CAUTION
Before replacing the presser foot, be sure to press (Presser foot/Needle exchange key)
on the operation panel to lock all keys and buttons, otherwise injuries may occur if the
“Start/Stop” button or any other button is pressed and the machine starts. For details on
changing the presser foot, refer to “Replacing the Presser Foot” in the “Basic operations”
section.
Sewing Tips
S-2
Trial sewing
After you have set up the machine with the thread and needle
appropriate for the type of fabric being sewn, the machine
automatically sets the stitch length and width for the stitch
that is selected. However, a trial piece of fabric should be
sewn since, depending on the type of fabric and stitching
being sewn, the desired results may not be achieved.
For the trial sewing, use a piece of fabric and thread that are
the same as those used for your project, and check the thread
tension and stitch length and width. Since the results differ
depending on the type of stitching and the number of layers of
fabric sewn, perform the trial sewing under the same
conditions that will be used with your project.
Changing the sewing direction
a
When the stitching reaches a corner, stop the machine.
Leave the needle lowered (in the fabric). If the needle
remains up when the machine stops sewing, press
(Needle position button) to lower the needle.
b
Raise the presser foot lever, and then turn the fabric.
Turn the fabric using the needle as a pivot.
c
Lower the presser foot lever and continue sewing.
Sewing curves
Stop sewing, and then slightly change the sewing direction to
sew around the curve. For details on sewing with an even
seam allowance, refer to “Sewing an even seam allowance”
on page S-3.
When sewing along a curve while using a zigzag stitch, select
a shorter stitch length in order to obtain a finer stitch.
Sewing cylindrical pieces
Removing the flat bed attachment allows for free-arm sewing,
making it easier to sew cylindrical pieces such as sleeve cuffs
and pant legs.
a
Pull the flat bed attachment off to the left.
b
Slide the part that you wish to sew onto the free arm,
and then sew from the top.
c
When you are finished with free arm sewing, install the
flat bed attachment back in its original position.
Chapter 1
SEWING ATTRACTIVE
FINISHES
Sewing Tips
Sewing Tips
Sewing S-3
SEWING ATTRACTIVE FINISHES
S
Sewing an even seam allowance
To sew an even seam, start sewing so that the seam allowance
is to the right of the presser foot, and the edge of the fabric is
aligned with either the right edge of the presser foot or a
marking on the needle plate.
Aligning the fabric with the presser foot
Sew while keeping the right edge of the presser foot a
fixed distance from the edge of the fabric.
1 Seam
2 Presser foot
Aligning the fabric with the stitch guide foot
(sold separately with some models)
Sew while keeping the right edge of the fabric aligned
with a desired position of markings on the stitch guide
foot.
1 Seam
2 Stitch guide foot
3 Markings
Aligning the fabric with a needle plate marking
The markings on the needle plate show the distance from
the needle position of a seam sewn with the straight stitch
(left needle position). Sew while keeping the edge of the
fabric aligned with a marking on the needle plate. The
distance between the markings in the upper scale is
1/8 inch (3 mm) and the distance between the markings in
the grid is 5 mm (3/16 inch).
For stitches with a left needle position
(Stitch width: 0.0 mm)
1 Seam
2 Presser foot
3 Centimeters
4 Inches
5 Needle plate
6 1.6 cm (5/8 inch)
1
2
1
2
3
Sewing Various Fabrics
S-4
Sewing thick fabrics
If the fabric does not fit under the presser foot
If the fabric does not fit easily under the presser foot, raise
the presser foot lever even higher to bring the presser foot
to its highest position.
If thick seams are being sewn and the fabric
does not feed at the beginning of stitching
The fabric may not feed when thick seams are being sewn
and the presser foot is not level, as shown below. In this
case, use the presser foot locking pin (black button on the
left side of zigzag foot “J” so that the presser foot remains
level while sewing, allowing the fabric to be fed smoothly.
1 Sewing direction
a
Raise the presser foot lever.
b
Align the beginning of stitching, and then position the
fabric.
c
While holding zigzag foot “J” level, hold the presser
foot locking pin (black button on the left side) pressed
in, and lower the presser foot lever.
1 Presser foot holding pin (black button)
d
Release the presser foot locking pin (black button).
The presser foot remains level, allowing the fabric to
be fed.
After the seam is sewn, the presser foot will return to
its original angle.
Sewing thin fabrics
When sewing thin fabrics, the stitching may become
misaligned or the fabric may not feed correctly. Move the
needle (be sure to use a fine needle) to the furthest left or right
hand position so that the fabric does not get pulled down into
the feed dog area. If this occurs, place thin paper or stabilizer
material under the fabric and sew it together with the fabric.
When you have finished sewing, tear off any excess paper.
1 Stabilizer material or paper
Sewing Various Fabrics
a
1
Memo
You may find adjusting the “Presser Foot
Pressure” in the settings screen helpful on some
thick fabrics.
(For models equipped with Automatic Fabric
Sensor System)
When “Automatic Fabric Sensor System” in the
settings screen is set to “ON”, the thickness of the
fabric is automatically detected by the internal
sensor so the fabric can be fed smoothly for best
sewing results. For details on the automatic fabric
sensor system, refer to “Automatic Fabric Sensor
System (Automatic presser foot pressure)” in the
“Basic operations” section.
CAUTION
If fabric more than 6 mm (15/64 inch) thick is
sewn or if the fabric is pushed with too much
force, the needle may bend or break.
1
Sewing Various Fabrics
Sewing S-5
SEWING ATTRACTIVE FINISHES
S
Sewing stretch fabrics
First, baste the pieces of fabric together, and then sew without
stretching the fabric.
1 Basting
For best results when sewing on knit fabrics use the stretch
stitches. Also be sure to use a needle for knits. The
recommended stitches and their stitch numbers are indicated
below.
* Stitch patterns can be selected directly by pressing the
numeric keys on the machine during preset utility stitch
mode. Refer to “Basic operations” section.
Sewing leathers or vinyl fabrics
When sewing fabrics that may stick to the presser foot such as
leathers or coated fabrics, change the presser foot to the non
stick foot*. The walking foot* is also suitable for sewing some
leathers or vinyl fabrics.
* Sold separately with some models.
1 Leather
Sewing hook-and-loop fastener tape
Make sure that the needle passes through the hook-and-loop
fastener tape by turning the handwheel and lower the needle
into the hook-and-loop fastener tape before sewing. And then,
sew the edge of the hook-and-loop fastener tape at a slow
speed.
If the needle does not pass through the hook-and-loop
fastener tape, replace the needle with the needle size for
thicker fabrics. For details, refer to “Fabric/thread/needle
combinations” in the “Basic operations” section.
1 Edge of the hook-and-loop fastener tape
Stitch
BLMAV 1-05 1-06 1-13 1-14 2-13
BLMSP/BLMLR
05
* 06*
13
14
*
48
BL210A
05
* 06*
11
12
*
42
Note
The walking foot can only be used with straight
or zigzag stitch patterns with reinforcement
stitches. For details, refer to “Stitch Setting
Chart” in the “Basic operations” section.
When using the walking foot, test sew on a scrap
piece of leather or vinyl that is to be used in
project to make sure foot does not leave any
marks.
1
1
CAUTION
Use only the adhesive-free hook-and-loop
fastener tape which is designed for sewing.
When the glue adheres to the needle or the
bobbin hook race, it may cause malfunction.
If the hook-and-loop fastener tape is sewn with
the thin needle (65/9-75/11), the needle may
bend or break.
Note
Before sewing, baste together the fabric and the
hook-and-loop fastener tape.
Basic Stitching
S-6
Straight stitches are used for sewing plain seams.
Using the table below, refer to “Using the utility
stitch tables in the “Sewing” section” in the “Basic
operations” section.
* Stitch patterns can be selected directly by pressing the
numeric keys on the machine during preset utility stitch
mode. Refer to “Basic operations” section.
Basting
When using BL210A: Sew basting with a stitch length of 5 mm
(3/16 inch).
When using BLMSP or BLMLR: Sew basting with a stitch
length between 5 mm (3/16 inch) and 30 mm (1-3/16 inches).
a
Attach zigzag foot “J”.
b
Select stitch
.
c
Start sewing.
Basic stitching
a
Baste or pin together the fabric pieces.
b
Attach zigzag foot “J”.
c
Select a stitch.
d
Lower the needle into the fabric at the beginning of the
stitching.
e
Lower the presser foot lever, and then start sewing.
f
When sewing is finished, cut the thread.
Chapter 2
UTILITY STITCHES
Basic Stitching
Stitch name Stitch
BLMAV
Presser foot
BLMSP/BLMLR
BL210A
Stitch number
Basting stitch 1-08 08 07
J
Straight stitch (Left)
1-01
01
* 01*
1-02
02
* 02*
Straight stitch (Middle) 1-03
03
* 03*
Straight stitch (Middle) 1-04
04* 04*
Triple stretch stitch 1-05
05
* 05*
J
J
Basic Stitching
Sewing S-7
UTILITY STITCHES
S
Changing the needle position
The needle position used as the baseline is different for the
straight stitch (left needle position) and the straight stitch
(center needle position).
1 Straight stitch (left needle position)
2 Straight stitch (center needle position)
When the stitch width of the straight stitch (left needle
position) is set to its standard setting (0.0 mm), the
distance from the needle position to the right side of the
presser foot is 12 mm (1/2 inch). If the stitch width is
changed (between 0 and 7.0 mm (1/4 inch)), the needle
position will also change. By changing the stitch width
and sewing with the right side of the presser foot aligned
with the edge of the fabric, a seam allowance can be sewn
with a fixed width.
1 Stitch width setting
2 Distance from the needle position to the right side of the
presser foot
3 12.0 mm (1/2 inch)
4 10.0 mm (3/8 inch)
5 6.5 mm (1/4 inch)
6 5.0 mm (3/16 inch)
For details, refer to “Setting the stitch width” in the
“Basic operations” section.
12
0.0 2.0 5.5 7.0
34 5
6
1
2
Blind Hem Stitching
S-8
Secure the bottoms of skirts and pants with a blind hem.
Using the table below, refer to “Using the utility
stitch tables in the “Sewing” section” in the “Basic
operations” section.
a
Turn the skirt or pants wrong side out.
1 Wrong side of fabric
2 Right side of fabric
3 Edge of fabric
4 Bottom side
b
Fold the fabric along the desired edge of the hem, and
press.
c
Use a chalk to mark on the fabric about 5 mm (3/16
inch) from the edge of the fabric, and then baste it.
d
Fold back the fabric inside along the basting.
e
Unfold the edge of fabric, and position the fabric with
the wrong side facing up.
f
Attach blind hem foot “R”.
g
Select or .
h
Remove the flat bed attachment to use the free arm.
Blind Hem Stitching
Stitch name Stitch
BLMAV
Presser foot
BLMSP/BLMLR
BL210A
Stitch number
Blind hem stitch 2-01 36 31
R
Blind hem stretch
stitch
2-02 37 32
Memo
When the size of cylindrical pieces is too small to
slide onto the arm or the length is too short, the
fabric will not feed and desired results may not be
achieved.
1 Wrong side of fabric
2 Right side of Fabric
3 Edge of fabric
4 Desired edge of hem
<Thick fabric>
<Normal fabric>
<Seen from the side>
2
1
3
1
2
1
2
1
3
3
4
2
1 Wrong side of fabric
2 Right side of fabric
3 Edge of fabric
4 Desired edge of hem
5 5 mm (3/16 inch)
6 Basting
<Thick fabric>
<Normal fabric>
<Seen from the side>
1 Wrong side of fabric
2 Right side of fabric
3 Edge of fabric
4 Desired edge of hem
5 5 mm (3/16 inch)
6 Basting
7 Basting point
<Thick fabric>
<Normal fabric>
<Seen from the side>
1 Wrong side of fabric
2 Right side of fabric
3 Edge of fabric
4 Desired edge of hem
5 Basting point
6 Basting
<Thick fabric>
<Normal fabric>
<Seen from the side>
1
2
1
2
3
5
6
4
1
2
1
3
6
5
1
1
2
7
4
5
1
1
1
1
1
2
6
3
4
Blind Hem Stitching
Sewing S-9
UTILITY STITCHES
S
i
Slide the item that you wish to sew onto the free arm,
make sure that the fabric feeds correctly, and then start
sewing.
1 Free arm
j
Position the fabric with the edge of the folded hem
against the guide of the presser foot, and then lower
the presser foot lever.
1 Wrong side of fabric
2 Fold of hem
3 Guide
k
Adjust the stitch width until the needle slightly catches
the fold of the hem.
1 Needle drop point
When you change the needle drop point, raise the
needle, and then change the stitch width.
1 Thick fabric
2 Normal fabric
If the needle catches too much of the hem fold
The needle is too far to the left.
Decrease the stitch width so that the needle slightly
catches the fold of the hem.
Example: Thick fabric
Example: Normal fabric
1 Wrong side of fabric
2 Right side of fabric
If the needle does not catch the hem fold
The needle is too far to the right.
Increase the stitch width so that the needle slightly catches
the fold of the hem.
Example: Thick fabric
Memo
Blind hem stitches cannot be sewn if the left
needle drop point does not catch the fold. If the
needle catches too much of the fold, the fabric
cannot be unfolded and the seam appearing on
the right side of the fabric will be very large,
leaving an unattractive finish. If you experience
either of these cases, perform the following
instructions to solve the problem.
1
2
Blind Hem Stitching
S-10
Example: Normal fabric
1 Wrong side of fabric
2 Right side of fabric
l
Sew with the fold of the hem against the presser foot
guide.
m
Press the “Start/Stop” button to stop sewing when you
are finished, and raise the presser foot and needle to
remove the fabric by pulling it back.
n
Remove the basting stitching and reverse the fabric.
1 Wrong side of fabric
2 Right side of fabric
Note
Be sure to pull the fabric backward after finished
sewing. If you pull the fabric toward side or
forward, the presser foot may be damaged.
1
2
Overcasting Stitches
Sewing S-11
UTILITY STITCHES
S
Sew overcasting stitches along the edges of cut fabric to
prevent them from fraying.
Sewing overcasting stitches using
overcasting foot “G”
Using the table below, refer to “Using the utility
stitch tables in the “Sewing” section” in the “Basic
operations” section.
* Stitch patterns can be selected directly by pressing the
numeric keys on the machine during preset utility stitch
mode. Refer to “Basic operations” section.
a
Attach overcasting foot “G”.
b
Select a stitch.
c
Position the fabric with the edge of the fabric against
the guide of the presser foot, and then lower the
presser foot lever.
1 Guide
d
Sew with the edge of the fabric against the presser foot
guide.
1 Needle drop point
e
Press the “Start/Stop” button to stop sewing when you
are finished, and raise the presser foot and needle to
remove the fabric by pulling it back.
Overcasting Stitches
Stitch name Stitch
BLMAV
Presser foot
BLMSP/BLMLR
BL210A
Stitch number
Overcasting stitch
1-15
15
* 13*
G1-16 16 14
1-17 17 15
G
a
CAUTION
After the stitch width is adjusted, rotate the
handwheel toward you (counterclockwise).
Check that the needle does not touch the
presser foot. If the needle hits the presser foot,
the needle may break and cause injury.
1 The needle should not touch the center bar
If the presser foot is raised to its highest level,
the needle may strike the presser foot.
1
Overcasting Stitches
S-12
Sewing overcasting stitches using zigzag foot
“J”
Using the table below, refer to “Using the utility
stitch tables in the “Sewing” section” in the “Basic
operations” section.
* Stitch patterns can be selected directly by pressing the
numeric keys on the machine during preset utility stitch
mode. Refer to “Basic operations” section.
a
Attach zigzag foot “J”.
b
Select a stitch.
c
Sew along the edge of the fabric with the needle
dropping off the edge at the right.
1 Needle drop point
1 Needle drop point
Sewing overcasting stitches using the side
cutter (sold separately with some models)
Using the side cutter, seam allowances can be finished
while the edge of the fabric is cut off. Five utility stitches
can be used to sew overcasting stitches with the side
cutter.
Using the table below, refer to “Using the utility
stitch tables in the “Sewing” section” in the “Basic
operations” section.
Side cutter
Stitch name Stitch
BLMAV
Presser foot
BLMSP/BLMLR
BL210A
Stitch number
Zigzag stitch 1-09
09
* 08*
J
Zigzag stitch (Right) 1-11 11 10
2 steps elastic zigzag
stitch
1-13 13 11
3 steps elastic zigzag
stitch
1-14
14
* 12*
Overcasting stitch
1-18 18 16
1-19 19 17
1-20 20 18
1-21 21 19
Single diamond
overcast stitch
1-22 22
1-23 23
J
a
Note
Thread the needle manually when using the side
cutter, or only attach the side cutter after
threading the needle using the needle threader.
Stitch name Stitch
BLMAV
Presser foot
BLMSP/BLMLR
BL210A
Stitch number
With side cutter
1-24 24 20
S
1-25 25 21
1-26 26 22
1-27 27 23
1-28 28 24
1
Overcasting Stitches
Sewing S-13
UTILITY STITCHES
S
a
Remove the presser foot.
b
Hook the connecting fork of the side cutter onto the
needle clamp screw.
1 Connecting fork
2 Needle clamp screw
c
Position the side cutter so that side cutter pin is aligned
with the notch in the presser foot holder, and then
slowly lower the presser foot lever.
1 Notch in presser foot holder
2 Pin
d
Raise the presser foot lever to check that the side
cutter is securely attached.
e
Pass the upper thread under the side cutter, and then
pull it out toward the rear of the machine.
f
Select a stitch.
g
Make a cut of about 2 cm (3/4 inch) long in the fabric
at the beginning of the stitching.
1 2 cm (3/4 inch)
h
Position the fabric in the side cutter.
The cut in the fabric should be positioned over the
guide plate of the side cutter.
1 Guide plate
If the fabric is not positioned correctly, the fabric will
not be cut.
i
Lower the presser foot lever, and then start sewing.
A seam allowance is cut while the stitching is sewn.
If the stitching is sewn in a straight line , the seam
allowance will be about 5 mm (3/16 inch).
1 5 mm (3/16 inch)
Note
When it is hard to set under the presser foot
holder, fit the pin on the side cutter into the notch
of the presser foot holder raising up the presser
foot lever higher.
b
a
b
a
Memo
The side cutter can cut as much as one layer of
13-oz. denim.
After using the side cutter, clean it by removing
any lint or dust.
If the side cutter can no longer cut fabric, use a
piece of cloth to apply a small amount of oil to the
cutting edge of the cutter.
1
a
1
Buttonhole Stitching/Button Sewing
S-14
Using the table below, refer to “Using the utility
stitch tables in the “Sewing” section” in the “Basic
operations” section.
Buttonhole sewing
The maximum buttonhole length is about 28 mm (1-1/8
inches) (diameter + thickness of the button).
Buttonholes are sewn from the front of the presser foot to the
back, as shown below.
1 Reinforcement stitching
The names of parts of buttonhole foot “A”, which is used to
create buttonholes, are indicated below.
1 Button guide plate
2 Presser foot scale
3 Pin
4 Marks on buttonhole foot
5 5 mm (3/16 inch)
Buttonhole Stitching/Button Sewing
Stitch name Stitch
BLMAV
Presser foot
BLMSP/BLMLR
BL210A
Stitch number
Narrow rounded
buttonhole stitch
4-01 77 57
A
Tapered round ended
buttonhole stitch
4-02 78 58
Round ended
buttonhole stitch
4-03 79 59
Narrow squared
buttonhole stitch
4-04 80 60
Stretch buttonhole
stitch
4-05 81 61
Heirloom buttonhole
stitch
4-06 82 62
Bound buttonhole
stitch
4-07 83 63
Keyhole buttonhole
stitch
4-08 84 64
Tapered keyhole
buttonhole stitch
4-09 85 65
Keyhole buttonhole
stitch
4-10 86 66
Button sewing stitch 4-14 90 70 M
5
2
1
3
4
A
Buttonhole Stitching/Button Sewing
Sewing S-15
UTILITY STITCHES
S
a
Use chalk to mark on the fabric the position and length
of the buttonhole.
1 Marks on fabric
2 Buttonhole sewing
b
Pull out the button guide plate of buttonhole foot “A”,
and then insert the button that will be put through the
buttonhole.
If the button does not fit in the button guide
plate
Add together the diameter and thickness of the button,
and then set the button guide plate to the calculated
length. (The distance between the markings on the presser
foot scale is 5 mm (3/16 inch).)
1 Presser foot scale
2 Length of buttonhole (diameter + thickness of button)
3 5 mm (3/16 inch)
Example: For a button with a diameter of
15 mm (9/16 inch) and a thickness of 10 mm (3/8 inch),
the button guide plate should be set to 25 mm (1 inch) on
the scale.
1 10 mm (3/8 inch)
2 15 mm (9/16 inch)
The size of the buttonhole is set.
c
Attach buttonhole foot “A”.
d
Select a stitch.
e
Position the fabric with the front end of the buttonhole
mark aligned with the red marks on the sides of the
buttonhole foot, and then lower the presser foot lever.
1 Mark on fabric (front)
2 Red marks on buttonhole foot
Pass the upper thread down through the hole in the
presser foot.
When lowering the presser foot, do not push in the
front of the presser foot.
1 Do not reduce the gap.
f
Pull down the buttonhole lever as far as possible.
1 Buttonhole lever
The buttonhole lever is positioned behind the bracket
on the buttonhole foot.
1 Buttonhole lever
2 Bracket
1
2
3
2
1
2
1
A
1
2
a
a
2
1
Buttonhole Stitching/Button Sewing
S-16
g
Gently hold the end of the upper thread in your left
hand, and then start sewing.
Once sewing is completed, the machine
automatically sews reinforcement stitches, then
stops.
h
Press (Thread cutter button) once.
Raise the presser foot, and then remove the fabric.
i
Raise the buttonhole lever to its original position.
j
Insert a pin along the inside of one bar tack at the end
of the buttonhole stitching to prevent the stitching
from being cut.
1 Pin
k
Use the seam ripper to cut towards the pin and open
the buttonhole.
1 Seam ripper
For keyhole buttonholes, use the eyelet punch to make
a hole in the rounded end of the buttonhole, and then
use the seam ripper to cut open the buttonhole.
1 Eyelet punch
When using the eyelet punch, place thick paper or
some other protective sheet under the fabric before
punching the hole in the fabric.
Changing the density of the stitching
Adjust the stitch length.
For details, refer to “Setting the stitch length” in the
“Basic operations” section.
If the fabric does not feed (for example, if it is too
thick), decrease the density of the stitching.
Changing the stitch width
Adjust the stitch width.
For details, refer to “Setting the stitch width” in the
“Basic operations” section.
Sewing buttonholes on stretch fabrics
When sewing buttonholes on stretch fabrics, use a gimp
thread.
Memo
If the automatic thread cutting setting was
selected before sewing, the machine will
automatically cut the threads at the end of the
stitching. For details, refer to “Automatically
cutting the thread” in the “Basic operations”
section.
When using the thread cutter on the left side of
the machine or scissors to cut the threads, press
(Needle position button) to raise the needle,
raise the presser foot, and then pull out the fabric
before cutting the threads.
1
1
CAUTION
When opening the buttonhole with the seam
ripper, do not place your hands in the cutting
direction, otherwise injuries may result if the
seam ripper slips.
Do not use the seam ripper in any other way
than how it is intended.
Memo
Before sewing buttonholes, check the stitch
length and width by sewing a trial buttonhole on a
scrap piece of fabric.
1
Buttonhole Stitching/Button Sewing
Sewing S-17
UTILITY STITCHES
S
a
Hook the gimp thread onto the part of buttonhole foot
“A” shown in the illustration.
b
It fits into the grooves, and then loosely tie it.
c
Attach buttonhole foot “A”.
d
Select stitch or .
e
Adjust the stitch width to the thickness of the gimp
thread.
f
Lower the presser foot lever and the buttonhole lever,
and then start sewing.
g
When sewing is finished, gently pull the gimp thread to
remove any slack.
h
Use a handsewing needle to pull the gimp thread to the
wrong side of the fabric, and then tie it.
Button sewing
Buttons can be sewn on with the machine. Buttons with two
or with four holes can be attached.
a
Measure the distance between the holes in the button
to be attached.
b
Raise the presser foot lever, and then slide the feed dog
position switch, located at the rear of the machine on
the base, to (to the left as seen from the rear of
the machine).
1 Feed dog position switch (as seen from the rear of the
machine)
c
Attach button fitting foot “M”.
d
Select stitch .
Since the end of the thread will be tied off later, do
not set the machine for programmed-thread cutting.
e
Adjust the stitch width so that it is the same as the
distance between the holes in the button.
f
Place the button in the position where it will be sewn,
and lower the presser foot lever.
1 Button
When attaching four-hole buttons, first sew the two
holes closest to you. Then, slide the button so that
the needle goes into the two holes toward the rear of
the machine, and then sew them in the same way.
a
a
Buttonhole Stitching/Button Sewing
S-18
g
Turn the handwheel toward you (counterclockwise) to
check that the needle correctly goes into the two holes
of the button.
If it seems as if the needle will hit the button, remeasure
the distance between the holes in the button. Adjust the
stitch width to the distance between the buttonholes.
h
Start sewing.
Set the sewing speed controller to the left (so that the
speed will be slow).
The machine automatically stops after sewing
reinforcement stitches.
Do not press (Thread cutter button).
i
Use scissors to cut the upper thread and the bobbin
thread at the beginning of the stitching.
Pull the upper thread at the end of the stitching to the
wrong side of the fabric, and then tie it with the bobbin
thread.
j
When you are finished attaching the button, slide the
feed dog position switch, to (to the right as seen
from the rear of the machine) and turn the handwheel
to raise the feed dogs.
Attaching a shank to a button
To sew the button with a shank, attach the button with
space between it and the fabric, and then wind the thread
by hand. This attaches the button securely.
a
Place the button into button fitting foot “M”, and then
pull the shank lever toward you.
1 Shank lever
b
After sewing is finished, cut the upper thread with
plenty of excess, wind it around the thread between
the button and the fabric, and then tie it to the upper
thread at the beginning of the stitching.
Tie together the ends of the bobbin thread at the end
and at the beginning of the stitching at the wrong side of
the fabric.
c
Cut off any excess thread.
CAUTION
When sewing, be sure that the needle does not
touch the button, otherwise the needle may
bend or break.
Memo
The feed dogs come up when you start sewing
again.
1
Zipper Insertion
Sewing S-19
UTILITY STITCHES
S
Using the table below, refer to “Using the utility
stitch tables in the “Sewing” section” in the “Basic
operations” section.
* Stitch patterns can be selected directly by pressing the
numeric keys on the machine during preset utility stitch
mode. Refer to “Basic operations” section.
Inserting a centered zipper
Stitching is sewn on both pieces of fabric butted against each
other.
1 Right side of fabric
2 Stitching
3 End of zipper opening
a
Attach zigzag foot “J”.
b
Sew straight stitches up to the zipper opening.
With the right sides of the fabric facing each other, sew
reverse stitches after reaching the zipper opening.
c
Using a basting stitch, continue sewing to the edge of
the fabric.
1 Basting stitching
2 Reverse stitches
3 Wrong side of fabric
4 End of zipper opening
d
Press open the seam allowance from the wrong side of
the fabric.
1 Wrong side of fabric
e
Align the seam with the center of the zipper, and then
baste the zipper in place.
1 Wrong side of fabric
2 Basting stitching
3 Zipper
f
Remove about 5 cm (2 inches) from the end of the
basting on the outside.
1 Wrong side of fabric
2 Zipper basting
3 Outside basting
4 5 cm (2 inches)
g
Attach the presser foot holder to the right pin of zipper
foot “I”.
1 Pin on the right side
2 Needle drop point
Zipper Insertion
Stitch name Stitch
BLMAV
Presser foot
BLMSP/BLMLR
BL210A
Stitch number
Straight stitch (Middle) 1-03
03
* 03*
J, I
1
2
3
1
2
3
4
1
1
2
3
4
1
2
3
2
1
I
Zipper Insertion
S-20
h
Select stitch .
i
Topstitch around the zipper.
1 Stitching
2 Right side of fabric
3 Basting stitching
4 End of zipper opening
j
Remove the basting stitching.
Inserting a side zipper
Stitching is visible on only one piece of fabric. Use this type of
zipper application for side openings and back openings.
1 Stitching
2 Right side of fabric
3 End of zipper opening
The following procedure will describe how to stitch on the left
side, as shown in the illustration.
a
Attach zigzag foot “J”.
b
Sew straight stitches up to the zipper opening.
With the right sides of the fabric facing each other, sew
reverse stitches after reaching the zipper opening.
c
Using a basting stitch, continue sewing to the edge of
the fabric.
1 Basting stitching
2 Reverse stitches
3 Wrong side of fabric
4 End of zipper opening
d
Press open the seam allowance from the wrong side of
the fabric.
1 Wrong side of fabric
CAUTION
When using zipper foot “I”, be sure to select
the straight stitch (center needle position), and
slowly turn the handwheel toward
you
(
counterclockwise)
to check that the needle
does not touch the presser foot. If a different
stitch is selected or the needle hits the presser
foot, the needle may bend or break.
CAUTION
When sewing, be sure that the needle does not
touch the zipper, otherwise the needle may
bend or break.
1
2
3
4
1
2
3
1
2
3
4
1
Zipper Insertion
Sewing S-21
UTILITY STITCHES
S
e
Press the seam allowance so that the right side (the side
that will not be stitched) has an extra 3 mm (1/8 inch).
1 Wrong side of fabric
2 3 mm (1/8 inch)
f
Align the zipper teeth with the pressed edge of the
fabric having the extra 3 mm (1/8 inch), and then baste
or pin the zipper in place.
1 Zipper teeth
2 Basting stitching
g
Attach the presser foot holder to the right pin of zipper
foot “I”.
If the stitching will be sewn on the right side, attach the
presser foot holder to the left pin of the zipper foot.
1 Pin on the right side
2 Needle drop point
h
Select stitch .
i
Sew the zipper to the piece of fabric with the extra 3
mm (1/8 inch), starting from the base of the zipper.
j
When you are about 5 cm (2 inches) from the end of
the zipper, stop the machine with the needle lowered
(in the fabric), raise the presser foot lever.
k
Open the zipper and continue sewing.
l
Close the zipper, turn over the fabric, and then baste
the other side of the zipper to the fabric.
1 Basting stitching
m
Attach the presser foot holder to the other pin of
zipper foot “I”.
If the presser foot holder was attached to the right pin in
step
g, change it to the left pin.
1 Pin on the left side
2 Needle drop point
CAUTION
When using zipper foot “I”, be sure to select
the straight stitch (center needle position), and
slowly turn the handwheel toward you
(
counterclockwise)
to check that the needle
does not touch the presser foot. If a different
stitch is selected or the needle hits the presser
foot, the needle may bend or break.
1
2
2
1
2
1
I
CAUTION
When sewing, be sure that the needle does not
touch the zipper, otherwise the needle may
bend or break.
1
I
1
2
Zipper Insertion
S-22
n
Topstitch around the zipper.
Sew reverse stitches at the end of the zipper opening
and align the zipper teeth with the side of the presser
foot.
1 Right side of fabric
2 End of zipper opening
3 Reverse stitches
4 Beginning of stitching
5 Basting stitching
o
When you are about 5 cm (2 inches) from the end of
the zipper, stop the machine with the needle lowered
(in the fabric), and then raise the presser foot lever.
p
Remove the basting stitching, open the zipper, and
then continue sewing.
CAUTION
When sewing, be sure that the needle does not
touch the zipper, otherwise the needle may
bend or break.
1
2
3
4
5
Zipper/piping Insertion
Sewing S-23
UTILITY STITCHES
S
A zipper and piping can be sewn in place.
Using the table below, refer to “Using the utility
stitch tables in the “Sewing” section” in the “Basic
operations” section.
* Stitch patterns can be selected directly by pressing the
numeric keys on the machine during preset utility stitch
mode. Refer to “Basic operations” section.
**Adjustable zipper/piping foot (sold separately with some
models)
Inserting a centered zipper
a
Refer to step af of “Inserting a centered zipper
on page S-19.
b
Remove the presser foot and presser foot holder to
attach the screw-on adjustable zipper/piping foot (sold
separately with some models).
For details on removing the presser foot holder, refer
to “Removing and attaching the presser foot holder”
in the “Basic operations” section.
c
Select stitch .
d
Loosen the positioning screw on the back of the presser
foot.
1 Positioning screw
e
Slide the presser foot over either the left or right feed
dog.
f
Change the needle position so that the needle does not
touch the presser foot.
For details, refer to “Setting the stitch width” in the
“Basic operations” section.
1 Needle drop point
g
Securely tighten the positioning screw.
1 Positioning screw
Zipper/piping Insertion
Stitch name Stitch
BLMAV
Presser foot
BLMSP/BLMLR
BL210A
Stitch number
Straight stitch (Left) 1-01
01
* 01***
Note
Make sure that the thread between the spool and
the bobbin is pulled tight.
1
CAUTION
After adjusting the needle position, slowly turn
the handwheel toward you (counterclockwise)
and check the needle does not touch the
presser foot. If the needle hits the presser foot,
the needle may bend or break.
Left sewing position
Right sewing position
1
1
Zipper/piping Insertion
S-24
h
Topstitch around the zipper.
1 Stitching
2 Right side of fabric
3 Basting stitching
4 End of zipper opening
i
Remove the basting stitching.
Inserting a piping
a
Place the piping between two fabrics inside out, as
shown below.
1 Fabric
2 Piping
3 Fabric
b
Refer to the steps of attaching the adjustable zipper/
piping foot on the previous page.
c
Sew along the piping.
d
After sewing, turn them over.
CAUTION
When sewing, be sure that the needle does not
touch the zipper, otherwise the needle may
bend or break.
1
2
3
4
1
2
3
Sewing Stretch Fabrics and Elastic Tape
Sewing S-25
UTILITY STITCHES
S
Using the table below, refer to “Using the utility
stitch tables in the “Sewing” section” in the “Basic
operations” section.
* Stitch patterns can be selected directly by pressing the
numeric keys on the machine during preset utility stitch
mode. Refer to “Basic operations” section.
Stretch stitching
a
Attach zigzag foot “J”.
b
Select stitch .
c
Sew the fabric without stretching it.
Elastic attaching
When elastic tape is attached to the cuff or waist of a piece of
clothing, the finished dimensions will be that of the stretched
elastic tape. Therefore, it is necessary that a suitable length of
the elastic tape be used.
a
Pin the elastic tape to the wrong side of the fabric.
Pin the elastic tape to the fabric at a few points to make
sure that the tape is uniformly positioned on the fabric.
1 Elastic tape
2 Pin
b
Attach zigzag foot “J”.
c
Select a stitch.
d
Sew the elastic tape to the fabric while stretching the
tape so that it is the same length as the fabric.
While pulling the fabric behind the presser foot with
your left hand, pull the fabric at the pin nearest the front
of the presser foot with your right hand.
Sewing Stretch Fabrics and Elastic Tape
Stitch name Stitch
BLMAV
Presser foot
BLMSP/BLMLR
BL210A
Stitch number
Stem stitch 1-06
06
* 06*
J
2 steps elastic zigzag
stitch
1-13
13 11
3 steps elastic zigzag
stitch
1-14
14
* 12*
Tape attaching stitch 2-13 48 42
J
CAUTION
When sewing, be sure that the needle does not
touch any pins, otherwise the needle may bend
or break.
1
2
J
Appliqué, Patchwork and Quilt Stitching
S-26
Using the table below, refer to “Using the utility
stitch tables in the “Sewing” section” in the “Basic
operations” section.
* Stitch patterns can be selected directly by pressing the
numeric keys on the machine during preset utility stitch
mode. Refer to “Basic operations” section.
Appliqué stitching
a
Cut out the appliqué, leaving a seam allowance of
between 3 and 5 mm (1/8 and 3/16 inch).
1 Seam allowance
b
Place a pattern made of thick paper or stabilizer on the
back of the appliqué, and then fold over the seam
allowance using an iron.
c
Turn the fabric over, and then baste or fuse it onto the
fabric that it will be attached to.
1 Basting stitching
d
Attach the zigzag foot “J” or the open toe foot (sold
Separately with some models) shown below.
e
Select a stitch.
Appliqué, Patchwork and Quilt Stitching
Stitch name Stitch
BLMAV
Presser foot
BLMSP/BLMLR
BL210A
Stitch number
Zigzag stitch 1-09
09
* 08*
J
Quilting appliqué
zigzag stitch
1-33 33 28
Blanket stitch 2-03 38 33
Quilting appliqué
stitch
1-34 34 29
Piecing stitch (Right) 1-29 29 25
Piecing stitch (Middle) 1-30 30 26
Piecing stitch (Left) 1-31 31
Patchwork join stitch 2-07 42 36
Patchwork double
overlock stitch
2-08 43 37
Couching stitch 2-09 44 38
Hand-look quilting
stitch
1-32 32 27
Quilting stippling
stitch
1-35 35 30
Memo
Patterns showing a “Q” in the table above are for
quilting and those showing a “P” are for piecing.
Zigzag foot “J” Open toe foot
1
1
J
Appliqué, Patchwork and Quilt Stitching
Sewing S-27
UTILITY STITCHES
S
f
Turn the handwheel toward you (counterclockwise),
and then begin sewing around the edge of the
appliqué, making sure that the needle drops just
outside of the appliqué.
When sewing around corners, stop the machine with
the needle in the fabric just outside of the appliqué,
raise the presser foot lever, and then turn the fabric as
needed to change the sewing direction.
Patchwork (crazy quilt) stitching
a
Fold the edge of the top piece of fabric and place it
over the lower piece.
b
Sew the two pieces of fabric together so the pattern
spans over both pieces.
Piecing
Sewing together two pieces of fabric is called “piecing”. The
fabric pieces should be cut with a 6.5 mm (1/4 inch) seam
allowance.
Sew a piecing straight stitch 6.5 mm (1/4 inch) from either the
right side or the left side of the presser foot.
a
Baste or pin along the seam allowance of the fabric
that you wish to piece together.
b
Attach zigzag foot “J”.
c
Select stitch or .
d
Sew with the side of the presser foot aligned with the
edge of the fabric.
For a seam allowance on the right side
Align the right side of the presser foot with the edge of the
fabric, and sew using stitch .
1 6.5 mm (1/4 inch)
For a seam allowance on the left side
Align the left side of the presser foot with the edge of the
fabric, and sew using stitch .
1 6.5 mm (1/4 inch)
Memo
To change the width of the seam allowance
(needle position), adjust the stitch width. For
details, refer to “Setting the stitch width” in the
“Basic operations” section.
J
1
1
Appliqué, Patchwork and Quilt Stitching
S-28
Piecing using the 1/4" quilting foot with guide
(sold separately with some models)
This quilting foot can sew an accurate 1/4 inch or 1/8 inch
seam allowance.
It can be used for piecing together a quilt or for
topstitching.
a
Press , and then attach the 1/4” quilting foot with
guide.
b
Use the guide and marks on the presser foot to sew
accurate seam allowances.
Piecing a 1/4 inch seam allowance
Sew keeping the edge of the fabrics against the guide.
1 Guide
2 1/4 inch
Creating an accurate seam allowance
Use the mark on the foot to begin, end, or pivot 1/4 inch
from edge of fabric.
1 Align this mark with edge of fabric to begin.
2 Beginning of stitching
3 End of stitching
4 Opposite edge of fabric to end or pivot
5 1/4 inch
Topstitching quilting, 1/8 inch
Sew with the edge of the fabric aligned with the left side of
the presser foot end.
1 Surface of fabric
2 Seam
3 1/8 inch
Using the 1/4" quilting foot (sold separately
with some models)
If the 1/4" quilting foot is used, seams can be sewn with a
seam allowance of 6.4 mm (1/4 inch).
a
Baste or pin along the seam allowance of the fabric
that you wish to piece together.
b
Attach the 1/4" quilting foot.
c
Select stitch .
d
Align the mark at the upper edge of the 1/4" quilting
foot with the upper edge of the fabric.
Align the right edge of the fabric with the right edge of
the narrow part of the 1/4" quilting foot.
1 Mark on 1/4" quilting foot
2 Beginning of stitching
When sewing with a seam allowance, align the left edge
of the narrow part of the 1/4" quilting foot with the
fabric edge.
1 Seam (3.2 mm (1/8 inch))
Memo
For details, refer to “Pivoting” in the “Basic
operations” section.
a
b
a
e
e
c
d
b
a
b
c
1
2
1
Appliqué, Patchwork and Quilt Stitching
Sewing S-29
UTILITY STITCHES
S
e
Start sewing.
f
When the end of the stitching is reached, stop the
machine.
Sew until the mark at the lower edge of the 1/4" quilting
foot aligns with the lower edge of the fabric.
1 6.4mm (1/4 inch)
2 End of stitching
3 Mark on 1/4" quilting foot
Quilting
Sandwiching batting between the top and bottom layers of
fabric is called “quilting”. Quilts can easily be sewn using the
walking foot* and the quilting guide*.
* Sold separately with some models.
a
Baste the fabric to be quilted.
b
Remove the presser foot and the presser foot holder.
For details, refer to “Removing and attaching the
presser foot holder” in the “Basic operations”
section.
c
Hook the connecting fork of the walking foot onto the
needle clamp screw.
1 Connecting fork
2 Needle clamp screw
d
Lower the presser foot lever, insert the presser foot
holder screw, and then tighten the screw with the
screwdriver.
1 Presser foot holder screw
e
Select a stitch.
f
Place one hand on each side of the presser foot, and
then evenly guide the fabric while sewing.
Note
Thread the needle manually when using the
walking foot, or only attach the walking foot after
threading the needle using the needle threader.
When sewing with the walking foot, sew at a
speed between slow and medium.
When quilting, use a 90/14 home machine
needle.
The walking foot can only be used with straight
or zigzag stitch patterns. Reverse stitches
cannot be sewn with the walking foot. Only
select straight or zigzag stitch patterns with
reinforcement stitches. For details, refer to
“Stitch Setting Chart” in the “Basic operations”
section.
(For models equipped with Automatic Fabric
Sensor System)
When “Automatic Fabric Sensor System” in the
settings screen is set to “ON”, the thickness of the
fabric is automatically detected by the internal
sensor so the fabric can be fed smoothly for best
sewing results. For details on the automatic fabric
sensor system, refer to “Automatic Fabric Sensor
System (Automatic presser foot pressure)” in the
“Basic operations” section.
2
3
1
CAUTION
Be sure to securely tighten the screws with the
screwdriver, otherwise the needle may touch
the presser foot, causing it to bend or break.
Before starting to sew, slowly turn the
handwheel toward you (counterclockwise)
and
check that the needle does not touch the
presser foot. If the needle hits the presser foot,
the needle may bend or break.
a
b
a
Appliqué, Patchwork and Quilt Stitching
S-30
Using the quilting guide (sold separately with
some models)
Use the quilting guide to sew parallel stitches that are
equally spaced.
a
Insert the stem of the quilting guide into the hole at the
rear of the walking foot or presser foot holder.
Walking foot
Presser foot holder
b
Adjust the stem of the quilting guide so that the guide
aligns with the seam that has already been sewn.
Free motion quilting
We recommend attaching the foot controller and sewing at a
consistent speed. You can adjust the sewing speed with the
speed control slide on the machine.
Using free motion open toe quilting foot “O”*
or quilting foot*
* Sold separately with some models.
The free motion open toe quilting foot “O” or quilting foot
is used for free motion quilting with zigzag or decorative
stitches or for free motion quilting of straight lines on
fabric with an uneven thickness. Various stitches can be
sewn using free motion open toe quilting foot “O”. For
details on the stitches that can be used, refer to “Stitch
Setting Chart” in the “Basic operations” section.
a
Slide the feed dog position switch, located at the rear
of the machine on the base, to (to the left as seen
from the rear of the machine).
1 Feed dog position switch (as seen from the rear of the
machine)
The feed dogs are lowered.
b
Select a stitch.
c
Remove the presser foot holder.
For details, refer to “Removing and attaching the
presser foot holder” in the “Basic operations”
section.
d
Attach free motion open toe quilting foot “O” by
positioning the pin of the quilting foot above the
needle clamp screw and aligning the lower-left of the
quilting foot and the presser bar.
1 Pin
2 Needle clamp screw
3 Presser bar
CAUTION
With free motion quilting, control the feeding
speed of the fabric to match the sewing speed.
If the fabric is moved faster than the sewing
speed, the needle may break or other damage
may result.
Memo
On models equipped with the free motion sewing
mode, the presser foot can be adjusted to the
best height for free motion sewing. For details,
refer to “Sewing with free motion mode” in the
“Basic operations” section.
Free motion open
toe quilting foot “O”
Quilting foot
Note
Make sure that the quilting foot is not slanted.
a
1
2
3
Appliqué, Patchwork and Quilt Stitching
Sewing S-31
UTILITY STITCHES
S
e
Hold the quilting foot in place with your right hand,
and tighten the presser foot holder screw using the
screwdriver with your left hand.
1 Presser foot holder screw
f
Use both hands to stretch the fabric taut, and then
move the fabric at a consistent pace in order to sew
uniform stitches roughly 2.0 mm - 2.5 mm (approx. 1/
16 inch - 3/32 inch) in length.
1 Stitch
g
After sewing is finished, slide the feed dog position
switch lever to (to the right as seen from the rear
of the machine) and turn the handwheel to raise the
feed dogs.
Using free motion quilting foot “C” (sold
separately with some models)
Use the free motion quilting foot “C” with straight stitch
needle plate for free motion sewing.
Free motion quilting foot “C”
a
Attach the straight stitch needle plate (sold separately
with some models).
For details on attaching the straight stitch needle
plate, refer to operation manual supplied with the
product.
1 Round hole
b
Slide the feed dog position switch, located at the rear
of the machine on the base, to (to the left as seen
from the rear of the machine).
1 Feed dog position switch (as seen from the rear of the
machine)
The feed dogs are lowered.
c
Select .
d
Remove the presser foot holder.
For details, refer to “Removing and attaching the
presser foot holder” in the “Basic operations”
section.
CAUTION
Be sure to securely tighten the screws with the
included screwdriver. Otherwise, the needle
may touch the quilting foot, causing it to bend
or break.
Memo
Do not be discouraged with your initial results.
The technique requires practice.
CAUTION
When using free motion quilting foot “C”, be
sure to use the straight stitch needle plate and
sew with the needle in middle (center) needle
position. If the needle is moved to any position
other than the middle (center) needle position,
the needle may break, which may result in
injuries.
Memo
On models equipped with the free motion sewing
mode, the presser foot can be adjusted to the
best height for free motion sewing. For details,
refer to “Sewing with free motion mode” in the
“Basic operations” section.
Memo
Notice this needle plate has a round hole for the
needle.
a
Appliqué, Patchwork and Quilt Stitching
S-32
e
Attach free motion quilting foot “C” at the front with
the presser foot holder screw aligned with the notch in
the quilting foot.
1 Presser foot holder screw
2 Notch
f
Hold the quilting foot in place with your right hand,
and tighten the presser foot holder screw using the
screwdriver with your left hand.
1 Presser foot holder screw
g
Use both hands to stretch the fabric taut, and then
move the fabric at a consistent pace in order to sew
uniform stitches roughly 2.0 mm - 2.5 mm (approx. 1/
16 inch - 3/32 inch) in length.
1 Stitch
h
After sewing is finished, slide the feed dog position
switch lever to (to the right as seen from the rear
of the machine) and turn the handwheel to raise the
feed dogs.
Echo quilting using the free motion echo
quilting foot “E” (sold separately with some
models)
Sewing quilting lines at equal distances around a motif is
called echo quilting. The quilting lines, which appear as
ripples echoing away from the motif, are the
distinguishing characteristic of this quilting style. Use the
optional free motion echo quilting foot “E” for echo
quilting. Using the measurement on the presser foot as a
guide, sew around the motif at a fixed interval. We
recommend attaching the foot controller and sewing at a
consistent speed.
Free motion echo quilting foot “E” measurement
1 6.4 mm (approx. 1/4 inch)
2 9.5 mm (approx. 3/8 inch)
Note
Make sure that the quilting foot is attached
properly and not slanted.
CAUTION
Be sure to securely tighten the screws with the
included screwdriver. Otherwise, the needle
may touch the quilting foot, causing it to bend
or break.
a
b
a
Note
Free motion open toe quilting foot “O” can also
be used with the straight stitch needle plate. We
recommend using free motion open toe quilting
foot “O” with free motion sewing of fabrics of
uneven thicknesses.
When using the straight stitch needle plate, all
straight stitches become middle needle position
stitches. You cannot change the needle position
using the width display.
Memo
Do not be discouraged with your initial results.
The technique requires practice.
Appliqué, Patchwork and Quilt Stitching
Sewing S-33
UTILITY STITCHES
S
a
Slide the feed dog position switch, located at the rear
of the machine on the base, to (to the left as seen
from the rear of the machine).
1 Feed dog position switch (as seen from the rear of the
machine)
The feed dogs are lowered.
b
Select .
c
Remove the presser foot holder (see the “Basic
operations” section) and the screw.
d
Position the free motion echo quilting foot “E” on the
left side of the presser bar with the holes in the quilting
foot and presser bar aligned.
e
Tighten the screw with the included screwdriver.
f
Using the measurement on the quilting foot as a guide,
sew around the motif.
1 6.4 mm (approx. 1/4 inch)
CAUTION
With free motion quilting, control the feeding
speed of the fabric to match the sewing speed.
If the fabric is moved faster than the sewing
speed, the needle may break or other damage
may result.
Memo
On models equipped with the free motion sewing
mode, the presser foot can be adjusted to the
best height for free motion sewing. For details,
refer to “Sewing with free motion mode” in the
“Basic operations” section.
a
CAUTION
Be sure to securely tighten the screws with the
included screwdriver. Otherwise, the needle
may touch the quilting foot, causing it to bend
or break.
Appliqué, Patchwork and Quilt Stitching
S-34
Finished project
g
After sewing is finished, slide the feed dog position
switch lever to (to the right as seen from the rear
of the machine) and turn the handwheel to raise the
feed dogs.
Satin stitching using the sewing speed
controller
A decorative stitch can be sewn by changing the stitch width
of a satin stitch. If the machine is set so that the stitch width
can be adjusted using the sewing speed controller, the stitch
width can quickly and easily be adjusted. In this case, the
sewing speed is adjusted with the foot controller.
a
Connect the foot controller.
b
Attach zigzag foot “J”.
c
Press to display the settings screen, and set
“Width Control” to “ON”.
The settings screens differ depending on the models.
The machine is now set so that the stitch width can
be controlled with the sewing speed controller.
d
Press .
e
Select stitch .
f
While sewing, slide the sewing speed controller to
adjust the stitch width.
Slide the controller to the left to make the width
narrower. Slide the controller to the right to make the
width wider.
Adjust the sewing speed with the foot controller.
g
When you are finished sewing, set the stitch width
control setting back to “OFF”.
J
Narrower Wider
Memo
Although the stitching result differs depending on
the type of fabric being sewn and the thickness of
the thread being used, for best results, adjust the
stitch length to between 0.3 and 0.5 mm (1/64 and
1/32 inch).
Reinforcement Stitching
Sewing S-35
UTILITY STITCHES
S
Reinforce points that will be subject to strain, such as sleeve
holes, inseams and pocket corners.
Using the table below, refer to “Using the utility
stitch tables in the “Sewing” section” in the “Basic
operations” section.
* Stitch patterns can be selected directly by pressing the
numeric keys on the machine during preset utility stitch
mode. Refer to “Basic operations” section.
Triple stretch stitching
Use triple stretch stitching to reinforce sleeve holes and
inseams.
a
Attach zigzag foot “J”.
b
Select stitch
.
c
Start sewing.
Bar tack stitching
Bar tacks are used to reinforce points subject to strain, such as
pocket corners and openings.
As an example, the procedure for sewing bar tacks at pocket
corners is described below.
a
Determine the desired length of the bar tack.
Set the button guide plate on buttonhole foot “A” to the
desired length. (The distance between the markings on
the presser foot scale is 5 mm (3/16 inch).)
1 Presser foot scale
2 Length of bar tack
3 5 mm (3/16 inch)
A bar tack with a maximum length of about 28 mm
(1–1/8 inches) can be sewn.
b
Attach buttonhole foot “A”.
c
Select stitch
.
d
Position the fabric so that the opening of the pocket
faces toward you, and then lower the presser foot lever
so that the needle drops 2 mm (1/16 inch) in front of
the pocket opening.
1 2 mm (1/16 inch)
Pass the upper thread down through the hole in the
presser foot.
Reinforcement Stitching
Stitch name Stitch
BLMAV
Presser foot
BLMSP/BLMLR
BL210A
Stitch number
Triple stretch stitch 1-05
05
* 05*
J
Bar tack stitch 4-13 89 69
A
Darning stitch
4-11
87
67
4-12 88 68
J
3
1
2
1
Reinforcement Stitching
S-36
When lowering the presser foot, do not push in the
front of the presser foot, otherwise the bar tack will
not be sewn with the correct size.
1 Do not reduce the gap.
e
Pull down the buttonhole lever as far as possible.
1 Buttonhole lever
The buttonhole lever is positioned behind the bracket
on the buttonhole foot.
1 Buttonhole lever
2 Bracket
f
Gently hold the end of the upper thread in your left
hand, and then start sewing.
g
Raise the presser foot lever, remove the fabric, and
then cut the threads.
h
Raise the buttonhole lever to its original position.
Darning
1 Reinforcement stitching
a
Determine the desired length of the darning.
Set the button guide plate on buttonhole foot “A” to the
desired length. (The distance between the markings on
the presser foot scale is 5 mm (3/16 inch).)
1 Presser foot scale
2 Length of darning
3 5 mm (3/16 inch)
4 7 mm (1/4 inch)
A bar tack with a maximum length of about 28 mm
(1-1/8 inches) can be sewn.
Once sewing is completed, the machine
automatically sews reinforcement stitches, then
stops.
b
Attach buttonhole foot “A”.
c
Select stitch or .
Memo
If the fabric does not feed, for example, because it
is too thick, increase the stitch length. For details,
refer to “Setting the stitch length” in the “Basic
operations” section.
a
a
2
1
1
2
4
3
Reinforcement Stitching
Sewing S-37
UTILITY STITCHES
S
d
Position the fabric so that the needle is 2 mm (1/16
inch) in front of the area to be darned.
1 Tear
2 2 mm (1/16 inch)
Pass the upper thread down through the hole in the
presser foot, and then lower the presser foot.
When lowering the presser foot, do not push in the
front of the presser foot, otherwise the darning will
not be sewn with the correct size.
1 Do not reduce the gap.
e
Pull down the buttonhole lever as far as possible.
1 Buttonhole lever
The buttonhole lever is positioned behind the bracket
on the buttonhole foot.
1 Buttonhole lever
2 Bracket
f
Gently hold the end of the upper thread in your left
hand, and then start sewing.
g
Raise the presser foot lever, remove the fabric, and
then cut the threads.
h
Raise the buttonhole lever to its original position.
2
1
a
a
2
1
Memo
If the fabric does not feed, for example, because it
is too thick, increase the stitch length. For details,
refer to “Setting the stitch length” in the “Basic
operations” section.
Eyelet Stitching
S-38
Eyelets, such as those on belts, can be sewn.
Using the table below, refer to “Using the utility
stitch tables in the “Sewing” section” in the “Basic
operations” section.
a
Attach monogramming foot “N”.
b
Select stitch
.
c
Adjust either the stitch width or the stitch length to
select the desired eyelet size.
1 7mm
2 6mm
3 5mm
For details, refer to “Setting the stitch width” and
“Setting the stitch length” in the “Basic operations”
section.
d
Lower the needle into the fabric at the beginning of the
stitching, and then lower the presser foot lever.
e
Start sewing.
Once sewing is completed, the machine
automatically sews reinforcement stitches, then
stops.
f
Use the eyelet punch to cut a hole in the center of the
eyelet.
When using the eyelet punch, place thick paper or
some other protective sheet under the fabric before
punching the hole in the fabric.
Eyelet Stitching
Stitch name Stitch
BLMAV
Presser foot
BLMSP/BLMLR
BL210A
Stitch number
Eyelet stitch 4-15 91 71 N
1
2
3
Memo
If thin thread is used, the stitching may be too
open. If this occurs, sew the eyelet twice before
removing the fabric, one on top of the other.
Attaching Patches or Emblems to Shirt Sleeves
Sewing S-39
UTILITY STITCHES
S
Use these stitch patterns to attach patches or emblems to
pant legs, shirt sleeves, etc.
Using the table below, refer to “Using the utility
stitch tables in the “Sewing” section” in the “Basic
operations” section.
Insert the tubular piece of fabric onto the free-arm, and then
sew in the order shown in the illustration.
a
Remove the flat bed attachment.
b
Attach monogramming foot “N”.
c
Select stitch .
d
Lower the needle into the fabric at the beginning of the
stitching, and then start sewing.
Lower the needle at the upper-right corner.
The fabric is fed toward the back of the machine, as
usual.
e
After you have sewn to the corner, stop the machine,
and then select stitch .
f
Start sewing.
The fabric is fed to the right.
g
After you have sewn to the corner, stop the machine,
and then select stitch .
h
Start sewing.
The fabric is fed forward.
i
After you have sewn to the corner, stop the machine,
and then select stitch .
j
Start sewing.
The fabric is fed to the left.
Attaching Patches or Emblems to Shirt Sleeves
Stitch name Stitch
BLMAV
Presser foot
BLMSP/BLMLR
BL210A
Stitch number
Reverse
(Straight stitch)
5-01 92
N
Sideways to left
(Straight stitch)
5-02 93
Sideways to right
(Straight stitch)
5-03 94
Forward
(Straight stitch)
5-04 95
Sideways to left
(Zigzag stitch)
5-05 96
Sideways to right
(Zigzag stitch)
5-06 97
Forward
(Zigzag stitch)
5-07 98
Reverse
(Zigzag stitch)
5-08 99
13
4
2
Attaching Patches or Emblems to Shirt Sleeves
S-40
k
After you have sewn to the corner, stop the machine,
and then select stitch again.
l
After sewing 3 to 5 stitches at the beginning of the
stitching, stop the machine.
Memo
The feeding direction of the fabric differs
depending on the stitch that is selected. Be sure
to guide the fabric while machine is sewing.
Decorative Stitching
Sewing S-41
UTILITY STITCHES
S
The utility stitches contain the following decorative
stitches.
Using the table below, refer to “Using the utility
stitch tables in the “Sewing” section” in the “Basic
operations” section.
Fagoting
Stitching across an open seam is called “fagoting”. It is used
on blouses and children's clothing. This stitch is more
decorative when thicker thread is used.
a
Use an iron to fold the two pieces of fabric along their
seams.
b
Baste the two pieces of fabric, separated by about 4
mm (3/16 inch), onto thin paper or a sheet of water-
soluble stabilizer.
If you draw a line down the middle of the thin paper or
water-soluble stabilizer, sewing is easier.
1 Thin paper or water soluble stabilizer
2 Basting stitching
3 4 mm (3/16 inch)
c
Attach zigzag foot “J”.
d
Select stitch or .
e
Set the stitch width to 7.0 mm (1/4 inch).
Decorative Stitching
Stitch name Stitch
BLMAV
Presser foot
BLMSP/BLMLR
BL210A
Stitch number
Patchwork join stitch 2-07 42 36
J
Patchwork double
overlock stitch
2-08 43 37
Couching stitch 2-09 44 38
Shell tuck edge stitch 2-04 39 34
Smocking stitch 2-10 45 39
Feather stitch 2-11 46 40
Fagoting cross stitch 2-12 47 41
Satin scallop stitch 2-05 40 35
N
Hemstitching
3-04 58 48
3-06 60 50
3-09 63
3-10 64 52
Honeycomb stitch 3-12 66
Hemstitching
3-18 72 56
3-20 74
3-21 75
3-22 76
Ladder stitch 2-14 49 43
J
Rick-rack stitch 2-15 50 44
Decorative stitch 2-16 51 45
Serpentine stitch 2-17 52 46 N
Stitch name Stitch
BLMAV
Presser foot
BLMSP/BLMLR
BL210A
Stitch number
2
1
3
J
Decorative Stitching
S-42
f
Sew with the center of the presser foot aligned along
the center of the two pieces of fabric.
g
After sewing is finished, remove the paper.
Scallop stitching
The wave-shaped repeated pattern that looks like shells is
called “scalloping”. It is used on the collars of blouses and to
decorate the edges of projects.
a
Attach monogramming foot “N”.
b
Select stitch .
c
Stitch along the edge of the fabric, making sure not to
sew directly on the edge of the fabric.
For better results, apply spray starch onto the fabric
and press with a hot iron before it is sewn.
d
Trim along the stitches.
Be careful not to cut the stitches.
Smocking
The decorative stitch created by stitching or embroidering
over gathers is called “smocking”. It is used to decorate the
front of blouses or cuffs.
The smocking stitch adds texture and elasticity to fabric.
a
Attach zigzag foot “J”.
b
Select the straight stitch, and then adjust the stitch
length to 4.0 mm (3/16 inch) and loosen the thread
tension.
For details, refer to “Setting the stitch length” and
“Setting the thread tension” in the “Basic operations”
section.
For details, refer to “Pulling up the bobbin thread” in
the “Basic operations” section.
c
Sew parallel stitching at intervals of 1 cm (3/8 inch).
1 1 cm (3/8 inch)
Do not use reverse/reinforcement stitching or thread
cutting.
At the end of the stitching, the thread is pulled out
about 5 cm (2 inches).
d
Pull the bobbin threads to create gathers.
Smooth the gathers by ironing them.
J
1
Decorative Stitching
Sewing S-43
UTILITY STITCHES
S
e
Select stitch , or .
f
Stitch between the straight stitches.
g
Pull out the threads for the straight stitches.
Shell tuck stitching
The gathers that look like shells are called “shell tucks”. They
are used to decorate trims, the front of blouses or cuffs made
of thin fabrics.
a
Fold the fabric along the bias.
b
Attach zigzag foot “J”.
c
Select stitch , and then increase the thread tension.
d
Sew while making sure that the needle drops slightly
off the edge of the fabric.
1 Needle drop point
e
Unfold the fabric, and then iron the tucks down to one
side.
Joining
Decorative bridging stitches can be sewn over the seam
allowance of joined fabrics. This is used when making a crazy
quilt.
a
Attach zigzag foot “J”.
b
Sew together the right sides of the two pieces of fabric,
and then open up the seam allowances.
1 Wrong side of fabric
2 7 mm (1/4 inch) seam allowance
3 Straight stitch
c
Select stitch , or .
J
1
J
1
1
2
3
Decorative Stitching
S-44
d
Turn the fabric over so that the right side faces up, and
then sew over the seam with the center of the presser
foot aligned with the seam.
1 Right side of fabric
Heirloom stitching
When sewing with the wing needle, the needle holes are
enlarged, creating a lace-like decorative stitch. This is used to
decorate hems and tablecloths on thin or mediumweight
fabrics in addition to plain weave fabrics.
a
Install the wing needle.
Use a 130/705H 100/16 wing needle.
For details on installing a needle, refer to “Replacing
the Needle” in the “Basic operations” section.
The needle threader cannot be used with the wing
needle, otherwise the machine may be damaged.
Manually pass the thread through the eye of the
needle from the front to the back.
For details, refer to “Threading the needle manually
(without using the needle threader)” in the “Basic
operations” section.
b
Attach monogramming foot “N”.
c
Select a stitch.
The stitches that can be used are , , , , , , ,
or .
When sewing with the wing needle, select a stitch
width of 6.0 mm (15/64 inch) or less.
d
Start sewing.
Partially removing threads is called “drawnwork”. This gives
beautiful results with fabrics that have a loose weave.
Two ways to create drawnwork are described below.
Drawnwork (Example 1)
a
Pull out several threads from the fabric.
b
Attach monogramming foot “N”.
c
Select stitch .
a
CAUTION
When sewing with the wing needle, select a
stitch width of 6.0 mm (15/64 inch) or less,
otherwise the needle may bend or break.
After adjusting the stitch width, slowly turn
the handwheel toward you (
counterclockwise)
and check that the needle does not touch the
presser foot. If the needle hits the presser foot,
the needle may bend or break.
Decorative Stitching
Sewing S-45
UTILITY STITCHES
S
d
With the right side of the fabric facing up, sew along
the right edge of the frayed section.
e
Press the mirror image key.
For details, refer to “Mirroring stitches” in the “Basic
operations” section.
The pattern displayed on the screen is mirrored.
f
Sew along the other edge of the frayed section so that
it looks like the previous stitching.
g
Press the mirror image key again to return to normal
mode.
Drawnwork (Example 2)
a
Pull out several threads from two sections of the fabric,
separated by an unfrayed section of about 4 mm (3/16
inch).
1 4 mm (3/16 inch)
b
Attach monogramming foot “N”.
c
Select stitch .
d
Sew along the center of the unfrayed section.
N
N
1
N
Decorative Stitching
S-46
Decorative
sewing
This section provides instructions on sewing character stitches and decorative stitches as well as on
adjusting and editing them.
Page number starts with “D” in this section.
The screen display and machine illustration may vary slightly, depending on the machine model.
Chapter1 CHARACTER / DECORATIVE STITCHES................ D-2
CAUTION
Before replacing the presser foot, be sure to press (Presser foot/Needle exchange key)
on the operation panel to lock all keys and buttons, otherwise injuries may occur if the
“Start/Stop” button or any other button is pressed and the machine starts. For details on
changing the presser foot, refer to “Replacing the Presser Foot” in the “Basic operations”
section.
Sewing the Various Built-in Decorative Patterns
D-2
Selecting stitch patterns
This machine is equipped with the following decorative
stitches and character stitches.
Decorative stitch patterns
The category contains the following three types of
stitches. Availability of stitches vary depending on your
machine model. Refer to the Quick Reference Guide.
Satin stitches
7 mm satin stitches
Cross stitch stitches
Character stitch patterns
To select a character/decorative stitch, press or , and
then use the numeric keys to specify the number of the
desired stitch.
Decorative stitch patterns
Each press of changes the decorative stitch category
in the following order.
ÆÆÆ...
Select the category containing the desired stitch, and then
specify the number of the stitch.
Chapter 1
CHARACTER /
DECORATIVE STITCHES
Sewing the Various Built-in Decorative Patterns
Note
The stitch numbers vary depending on your
sewing machine model. Refer to the Quick
Reference Guide.
Operation
key
Included stitches Icon
Decorative stitches
Satin stitches
7 mm satin stitches
Cross stitch stitches
Utility decorative stitches
Operation
key
Font Icon
Gothic
Handwriting
Outline
Cyrillic
Japanese
Memo
For stitches 01 through 09, the stitch can also be
selected by using the numeric keys to type in a
one-digit number, then pressing .
When using one-digit numbers and it is entered
incorrectly, press to erase the entered
number.
Sewing the Various Built-in Decorative Patterns
Decorative sewing D-3
CHARACTER / DECORATIVE STITCHES
D
Character stitch patterns
Each press of changes the font in the following order.
ÆÆÆÆÆ...
Select the desired font, and then specify the numbers of
the desired characters.
Deleting a pattern
To remove a selected pattern, press on the operation
panel.
The selected pattern is removed.
Sewing attractive finishes
To achieve attractive results when sewing
character/decorative stitches, check the table below for the
proper fabric/thread/needle combinations.
Memo
When selecting a pattern from a category
containing over 100 patterns, the pattern can be
selected by entering its three-digit number (for
example, 001) without pressing . When one or
two digits are entered and if the pattern cannot be
selected with the entered number, press to
confirm the pattern number.
Memo
If a new pattern is selected without deleting the
previously selected one, the first and second
patterns are combined. (Refer to “Combining
patterns” on page D-5.)
If two patterns or more have been already
selected, the pattern that was selected last is
removed.
Note
Other factors, such as fabric thickness, stabilizer
material, etc., also have an effect on the stitch,
so you should always sew a few trial stitches
before beginning your project.
It may be necessary to adjust the pattern,
depending on the type of fabric being sewn or
the sewing speed. Adjust the pattern while
sewing trial stitches on a scrap piece of fabric
that is the same as what is used in your project.
Refer to “Realigning the pattern” on page D-10.
When sewing satin stitch patterns, there may be
shrinking or bunching of stitches, so be sure to
attach a stabilizer material.
Guide the fabric with your hand to keep the
fabric feeding straight and even during sewing.
Fabric When sewing on stretch fabrics, lightweight
fabrics, or fabrics with coarse weaves, attach
stabilizer on the wrong side of the fabric. An
alternative would be to place the fabric on thin
paper such as tracing paper.
1 Fabric
2 Stabilizer
3 Thin paper
Thread #50 - #60
Needle With lightweight, regular, or stretch fabrics: the Ball
point needle (golden colored) 90/14
With heavyweight fabrics: home machine needle
90/14
Presser foot Monogramming foot “N”.
Using zigzag foot “J” or other presser feet may
give inferior results.
Twin needle You can sew with twin needle (2.0/11) when you
select 7 mm satin stitch pattern. In this case, use
zigzag foot “J”.
Sewing the Various Built-in Decorative Patterns
D-4
Basic sewing
a
Select a decorative/character stitch pattern.
b
Attach monogramming foot “N”.
c
Place the fabric under the presser foot, pull the upper
thread out to the side, press (Needle position
button) to lower needle into fabric and then lower the
presser foot.
d
Press the “Start/Stop” button to begin sewing.
e
Press the “Start/Stop” button to stop sewing.
f
Press (Reverse stitch button) or (Reinforcement
stitch button) to sew reinforcement stitches.
CAUTION
When sewing 7 mm satin stitch patterns and
the stitches are bunched, lengthen the stitch
length. If you continue sewing when the
stitches are bunched, the needle may bend or
break. For details on adjusting the stitch
length, refer to “Setting the stitch length” in
the “Basic operations” section.
Memo
If the fabric is pulled or pushed during sewing, the
pattern may not turn out correctly. Also,
depending on the pattern, there may be
movement to the left and right as well as front and
back. Guide the fabric with your hand to keep the
fabric feeding straight and even during sewing.
Memo
When sewing character stitches, the machine
automatically sews reinforcement stitches at the
beginning and end of each character.
When sewing is completed, trim any excess
thread between letters.
Note
When sewing some patterns, the needle will
temporarily pause in the raised position while the
fabric is fed due to the operation of the needle
bar separation mechanism which is used in this
machine. At such times, a clicking sound
different from the sound generated during
sewing will be heard. This sound is normal and is
not the sign of a malfunction.
Sewing the Various Built-in Decorative Patterns
Decorative sewing D-5
CHARACTER / DECORATIVE STITCHES
D
Combining patterns
a
Select the first category and pattern.
The selected pattern appears on the screen.
When the sewing is started, the selected pattern is
sewn repeatedly until the sewing machine is
stopped.
b
Select the next category and pattern.
The combined pattern appears on the screen.
To remove a selected pattern, press on the
operation panel. The pattern that was selected last is
removed.
c
After all of the desired patterns are selected, start
sewing.
The order that the patterns appear on the screen is
the order that they will be sewn.
Repeating combined patterns
When multiple stitches are combined, the sewing machine
stops when the pattern displayed on the screen has been
completed. Use the following operations to sew a combined
pattern repeatedly.
a
After the patterns have been combined, press .
on the LCD screen turns to , and you can
now sew the specified pattern repeatedly.
If pressed again, it turns to (single sewing).
Memo
Up to 70 patterns can be combined.
If multiple patterns have been combined, the
sewing machine stops once all the selected
patterns displayed in the LCD have been sewn. To
repeatedly sew the combined pattern, refer to
“Repeating combined patterns” on page D-5.
The combined pattern can be stored for later use.
For details, refer to “Saving a pattern” on
page D-9.
When you created a combined pattern using a
pattern which allows stitch width/length
adjustment and one which does not allow, you
can adjust the stitch width/length of the created
pattern. However, the changed value will be
applied only to the pattern which allows stitch
width/length adjustment.
Note
If repeated sewing is set, the pattern is
repeatedly sewn until the sewing machine is
stopped.
If the sewing machine is turned off, the
repeated/single sewing setting returns to its
default setting.
Sewing the Various Built-in Decorative Patterns
D-6
Checking the selected pattern
When the specified pattern is not displayed on the screen,
check the pattern using the following steps.
a
Select (Check) in the settings screen.
b
Press the “-” or “+” key, and confirm the pattern.
c
Press .
Changing the pattern size
The size of character stitches (except handwriting font) can be
switched between large and small. Depending on your
machine model, the size of Handwriting font characters,
Decorative stitches, Satin stitches can be also changed. Refer
to “Functions available with each model” in the “Basic
operations” section.)
a
Select a stitch.
b
Display (Size selection) in the settings screen, and
select (Large) or (Small).
Large
Small
c
Repeat steps a and b.
Changing the stitch density
If a satin stitch has been selected, the stitch density can be
changed.
a
Select a satin stitch pattern.
b
Select (Thread density) in the settings screen, and
select the desired stitch density.
Select for coarser stitching, or select for finer
stitching.
Memo
The combined pattern can be stored for later use.
For details, refer to “Saving a pattern” on
page D-9.
CAUTION
If the stitching density is too fine, depending
on the needle, the stitches may be bunched
together, causing the needle to break.
Sewing the Various Built-in Decorative Patterns
Decorative sewing D-7
CHARACTER / DECORATIVE STITCHES
D
Changing the pattern length
The length of one part of a 7 mm satin stitch can be set to one
of five sizes.
a
Select a 7 mm satin stitch pattern.
b
Select (Elongation) in the settings screen, and select
the desired length from among “1” to “5”.
Changing character spacing
a
Select character stitches.
b
Select (Character spacing) in the settings screen.
c
Adjust the character spacing by pressing the “-” or “+”
key.
The higher the setting, the wider the character spacing
will be; the lower the setting, the narrower the character
spacing will be.
Creating step stitch patterns
(For models equipped with step stitch
patterns)
Decorative stitches can be shifted to the left or right by half
the width of the pattern, allowing you to create a step-shaped
pattern. (Equipped on some models. Refer to page B-6.) This is
called a “step stitch pattern”. As an example, the procedure
for creating the following pattern is described below.
a
Select a decorative stitch.
b
Press .
The next pattern selected is moved half a width to the
right.
c
Select the same pattern.
Sewing the Various Built-in Decorative Patterns
D-8
d
Press .
The next pattern selected is moved half a width to the
left.
e
Press to specify that the patterns will be sewn
repeatedly.
For details, refer to “Repeating combined patterns”
on page D-5.
Examples of step stitch patterns
Mirroring a pattern image
a
After a single pattern has been selected, press to
mirror the pattern image horizontally.
appears on the screen and the selected stitch is
mirrored.
Sewing the Various Built-in Decorative Patterns
Decorative sewing D-9
CHARACTER / DECORATIVE STITCHES
D
Returning to the beginning of the pattern
You can return to the beginning of the pattern after trial
sewing or when the stitching is sewn incorrectly.
a
Press the “Start/Stop” button to stop the machine, and
then press .
Sewing returns to the beginning of the selected
pattern (“W”) from the point where sewing was
stopped.
b
Press the “Start/Stop” button to continue sewing.
Saving a pattern
Combined patterns can be stored for later use. Since stored
patterns are not lost after the sewing machine is turned off,
they can be recalled at any time. Up to 15 patterns can be
stored.
a
Create the combined pattern that you wish to store.
For details, refer to “Combining patterns” on
page D-5.
b
Press on the operation panel.
A screen showing the list of pockets appears, and an
empty pocket is selected.
c
Press .
Do not turn off the sewing machine while the pattern
is being stored, otherwise the pattern data may be
lost.
Memo
If this key is pressed when sewing is stopped,
patterns can be added at the end of a combined
stitch pattern. (In this example, “!” is added.)
Memo
To select the pocket where the pattern is to be
saved, press or to specify the
desired pocket, and then press .
If the pattern is saved in a pocket where a stitch is
already saved, the stitch is overwritten.
If an empty pocket is not available, select a
pocket which contains a pattern that can be
overwritten.
Use to scroll the selected pocket
horizontally to confirm the whole pattern.
Once the pattern has been saved in pocket, it can
not be deleted without overwriting. When you
wish to delete a pattern in the pocket, press
without selecting a pattern.
Sewing the Various Built-in Decorative Patterns
D-10
Retrieving a pattern
a
Press once or twice until a list of saved patterns
like the one shown below is displayed.
b
Select the desired saved pattern using or
.
The selected pocket is shown in reverse highlighting,
and the stored pattern is displayed.
c
Check the contents, and then press .
Realigning the pattern
The pattern may not be sewn correctly, depending on the type
of fabric being sewn or the sewing speed. If this occurs, adjust
the pattern while sewing on a piece of scrap fabric that is the
same as what is used for your project.
The pattern used for making adjustments differs depending on
the sewing machine model.
For models equipped with vertical and horizontal fine
adjustment settings: (No. 36 or 80 of )
For models equipped with only vertical fine adjustment
settings: (No. 31 of )
a
Attach monogramming foot “N”.
b
Select or .
c
Start sewing.
The sewing machine stops after it has finished sewing
the pattern.
d
Check the sewn pattern.
If the part of the pattern indicated in the illustration is
sewn uniformly, the pattern is correctly aligned.
If the pattern appears as shown below, the stitching is
misaligned in the vertical direction.
(For models equipped with horizontal fine adjustment
settings)
If the pattern appears as shown below, the stitching is
misaligned in the horizontal direction.
If the pattern is not sewn correctly, follow the steps
below to adjust the sewing.
e
Select (Fine adjustment – vertical) in the settings
screen.
Memo
Use to scroll the selected pattern
horizontally to confirm the whole pattern.
Sewing the Various Built-in Decorative Patterns
Decorative sewing D-11
CHARACTER / DECORATIVE STITCHES
D
f
Press the “-” or “+” key to adjust the vertical position.
Make the necessary adjustments according to how
the pattern is sewn.
Press “+” to increase the vertical space in the design.
Press “-” to decrease the vertical space in the design.
For users of models equipped with horizontal fine
adjustment settings:
Go to step 7.
For users of models equipped with only vertical fine
adjustment settings:
Go to step 9.
g
Select (Fine adjustment – horizontal) in the
settings screen.
h
Press the “-” or “+” key to adjust the horizontal
position.
Make the necessary adjustments according to how
the pattern is sewn.
Press “+” to increase the horizontal space in the design.
Press “-” to decrease the horizontal space in the design.
i
Press .
j
Select or once again, start the sewing
machine and check the stitching.
Continue adjusting the pattern until it is sewn correctly.
Sewing the Various Built-in Decorative Patterns
D-12
Appendix
This section provides important information for operating this machine. Please read this section to find
troubleshooting tips and pointers as well as how to keep your machine in the best working order.
Page number starts with “A” in this section.
Chapter1 MAINTENANCE AND TROUBLESHOOTING........ A-2
Care and Maintenance
A-2
Restrictions on oiling
In order to prevent damaging this machine, it must not be
oiled by the user.
This machine was manufactured with the necessary amount
of oil applied to ensure correct operation, making periodic
oiling unnecessary.
If problems occur, such as difficulty turning the handwheel or
an unusual noise, immediately stop using the machine, and
contact your authorized Baby Lock retailer.
Precautions on storing the machine
Do not store the machine in any of the locations described
below, otherwise damage to the machine may result, for
example, rust caused by condensation.
Exposed to extremely high temperatures
Exposed to extremely low temperatures
Exposed to extreme temperature changes
Exposed to high humidity or steam
Near a flame, heater or air conditioner
Outdoor or exposed to direct sunlight
Exposed to extremely dusty or oily environments
Cleaning the LCD screen
If the screen is dirty, gently wipe it with a soft, dry cloth. Do
not use organic solvents or detergents.
Cleaning the machine surface
If the surface of the machine is dirty, lightly soak a cloth in
neutral detergent, squeeze it out firmly, and then wipe the
surface of the machine. After cleaning it once with a damp
cloth, wipe it again with a dry cloth.
Cleaning the race
Sewing performance will suffer if lint and dust collects in the
bobbin case, therefore, it should be cleaned regularly.
a
Press (Needle position button) to raise the needle.
b
Turn off the machine.
c
Unplug the power cord from the power supply jack on
the right side of the machine.
d
Raise the presser foot to remove the needle, presser
foot and presser foot holder.
For details, refer to “Replacing the Needle” and
“Replacing the Presser Foot” in the “Basic
operations” section.
e
Remove the flat bed attachment if it is attached.
Chapter 1
MAINTENANCE AND
TROUBLESHOOTING
Care and Maintenance
Note
In order to extend the life of this machine,
periodically turn it on and use it.
Storing this machine for an extended period of
time without using it may reduce its efficiency.
Note
Do not wipe the LCD screen with a damp cloth.
Memo
Occasionally, condensation may form on the LCD
screen or it may become fogged up; however, this
is not a malfunction. After a while, the cloudiness
will disappear.
CAUTION
Unplug the power cord before cleaning the
machine, otherwise injuries or an electric
shock may occur.
CAUTION
Unplug the power cord before cleaning the
machine, otherwise injuries or an electric
shock may occur.
Care and Maintenance
Appendix A-3
MAINTENANCE AND TROUBLESHOOTING
A
f
Remove the needle plate cover.
Grasp both sides of the needle plate cover, and then
slide it toward you.
1 Needle plate cover
g
Remove the bobbin case.
Grasp the bobbin case, and then pull it out.
1 Bobbin case
h
Use the cleaning brush or a vacuum cleaner to remove
any lint and dust from the race and the surrounding
area.
1 Cleaning brush
2 Race
Do not apply oil to the bobbin case.
i
Insert the bobbin case so that the
S
mark on the
bobbin case aligns with the
z mark on the machine.
Align the S and
z marks.
1 S mark
2
z mark
3 Bobbin case
Make sure that the indicated points are aligned
before installing the bobbin case.
j
Insert the tabs on the needle plate cover into the
needle plate, and then slide the cover back on.
1 Needle plate cover
a
1
a
b
b
a
CAUTION
Never use a bobbin case that is scratched,
otherwise the upper thread may become
tangled, the needle may break or sewing
performance may suffer. For a new bobbin
case, contact your nearest authorized Baby
Lock retailer.
Be sure that the bobbin case is correctly
installed, otherwise the needle may break.
a
Troubleshooting
A-4
If the machine stops operating correctly, check the
following possible problems before requesting service.
You can solve most problems by yourself. Visit us at
“ www.babylock.com
”.
If the problem persists, contact your authorized Baby Lock
retailer.
Frequent troubleshooting topics
Detailed causes and remedies for common troubleshooting
topics are described below. Be sure to refer to this before
contacting us.
Upper thread tightened up
Symptom
The upper thread appears as a single continuous line.
The lower thread is visible from the upper side of the
fabric. (Refer to the illustration below.)
The upper thread has tightened up, and comes out
when pulled.
The upper thread has tightened up, and wrinkles
appear in the fabric.
The upper thread tension is tight, and the results do
not change even after the thread tension is adjusted.
1 Wrong side of fabric
2 Bobbin thread visible from right side of fabric
3 Upper thread
4 Right side of fabric
5 Bobbin thread
Cause
Incorrect bobbin threading
If the bobbin thread is incorrectly threaded, instead of the
appropriate tension being applied to the bobbin thread, it
is pulled through the fabric when the upper thread is
pulled up. For this reason, the thread is visible from the
right side of the fabric.
Remedy/check details
Correctly install the bobbin thread.
a
Press , and raise the presser foot lever.
b
Remove the bobbin from the bobbin case.
c
Place the bobbin in the bobbin case so that the thread
unwinds in the correct direction.
Hold the bobbin with your right hand with the thread
unwinding to the left, and hold the end of the thread
with your left hand.
Then, with your right hand, place the bobbin in the
bobbin case.
If the bobbin is inserted with the thread unwinding in
the wrong direction, sewing will be done with an
incorrect thread tension.
d
While holding the bobbin in place with your finger,
pass the thread through the slit in the needle plate
cover.
Hold down the bobbin with your right hand, and
then pull the end of the thread around the tab with
your left hand.
1 Tab
2 Hold down the bobbin with your right hand.
Troubleshooting
Upper thread tightened up page A-4
Tangled thread on wrong side of fabric page A-5
Incorrect thread tension page A-6
Fabric is caught in the machine and cannot
be removed
page A-7
When the thread becomes tangled under
the bobbin winder seat
page A-10
Troubleshooting
Appendix A-5
MAINTENANCE AND TROUBLESHOOTING
A
Pull the thread to pass it through the slit in the needle
plate cover, then cut it with the cutter.
3 Slit
4 Cutter
Sewing with the correct thread tension is possible after
the bobbin has been correctly installed in the bobbin
case.
e
Press to unlock all keys and buttons.
Tangled thread on wrong side of fabric
Symptom
The thread becomes tangled on the wrong side of the
fabric.
After starting sewing, a rattling noise is made and
sewing cannot continue.
Looking under the fabric, there is tangled thread in
the bobbin case.
Cause
Incorrect upper threading
If the upper thread is incorrectly threaded, the upper
thread passed through the fabric cannot be firmly pulled
up and the upper thread becomes tangled in the bobbin
case, causing a rattling noise.
Remedy/check details
Remove the tangled thread, and then correct the upper
threading.
a
Remove the tangled thread. If it cannot be removed,
cut the thread with scissors.
For details, refer to “Cleaning the race” on page A-2.
b
Remove the upper thread from the machine.
If the bobbin was removed from the bobbin case,
refer to “Installing the bobbin” in the “Basic
operations” section and “Remedy/check details” in
the section “Upper thread tightened up” on page A-4
to correctly install the bobbin.
c
Refer to the following steps to correct the upper
threading. Raise the presser foot using the presser foot
lever.
1 Presser foot lever
The upper thread shutter opens so the machine can
be threaded.
If the presser foot is not raised, the machine cannot
be threaded correctly.
d
Press (Needle position button) once or twice to
raise the needle.
The needle is correctly raised when the mark on the
handwheel is at the top, as shown below. Check the
handwheel and, if this mark is not at this position,
press (Needle position button) until it is.
1 Mark on handwheel
e
While holding the thread lightly with your right hand,
pull the thread with your left hand, and then pass the
thread behind the thread guide cover and to the front.
1 Thread guide cover
1
1
1
Troubleshooting
A-6
f
Pass the thread under the thread guide plate, and then
pull it up.
1 Thread guide plate
g
While using your right hand to lightly hold the thread
passed under the thread guide plate, pass the thread
through the thread path in the order shown below.
1 Shutter
h
Lower the presser foot.
i
Press .
j
Slide the thread behind the needle bar thread guide.
The thread can easily be passed behind the needle bar
thread guide by holding the thread in your left hand,
then feeding the thread with your right hand, as shown.
1 Needle bar thread guide
k
Next, use the needle threader to thread the needle.
Continue with the procedure in “Threading the
needle” in the “Basic operations” section.
Incorrect thread tension
Symptoms
Symptom 1: The bobbin thread is visible from the
right side of the fabric. (Refer to illustration below)
Symptom 2: The upper thread appears as a straight
line on the right side of the fabric.
Symptom 3: The upper thread is visible from the
wrong side of the fabric. (Refer to illustration below)
Symptom 4: The bobbin thread appears as a straight
line on the wrong side of the fabric.
Symptom 5: The stitching on the wrong side of the
fabric is loose or has slack.
Symptom 1
Symptom 3
1 Wrong side of fabric
2 Bobbin thread visible from right side of fabric
3 Upper thread
4 Right side of fabric
5 Bobbin thread
6 Upper thread visible from wrong side of fabric
Cause/remedy/check details
Cause 1
The machine is not correctly threaded.
<With symptoms 1 and 2 described above>
The bobbin threading is incorrect.
Return the upper thread tension to the standard setting,
and then refer to “Upper thread tightened up” on page A-4
to correct the threading.
<With symptoms 3 and 5 described above>
The upper threading is incorrect.
Return the upper thread tension to the standard setting,
and then refer to “Tangled thread on wrong side of fabric”
on page A-5 to correct the upper threading.
1
1
Troubleshooting
Appendix A-7
MAINTENANCE AND TROUBLESHOOTING
A
Cause 2
A needle and thread appropriate for the fabric are not
being used.
The machine needle that should be used depends on the
type of fabric sewn and the thread thickness.
If a needle and thread appropriate for the fabric are not
being used, the thread tension will not be adjusted
correctly, causing wrinkles in the fabric or skipped
stitches.
Refer to “Fabric/thread/needle combinations” in the
“Basic operations” section to check that a needle and
thread appropriate for the fabric are being used.
Cause 3
An appropriate upper tension is not selected.
The setting selected for the upper thread tension is not
appropriate.
Refer to “Setting the thread tension” in the “Basic
operations” section to select an appropriate thread
tension.
The appropriate thread tension differs depending on the
type of fabric and thread being used.
* Adjust the thread tension while test sewing on a
piece of scrap fabric that is the same as that used in
your project.
If the bobbin thread is visible from the right side of
the fabric
Using thread tension key (For models equipped with
thread tension key. Refer to page B-6)
Press “-” to decrease the tension of the upper thread.
Using thread tension dial (For models equipped with
thread tension dial. Refer to page B-6)
Turn the thread tension dial to the left to decrease the
tension of the upper thread.
If the upper thread is visible from the wrong side of
the fabric
Using thread tension key (For models equipped with
thread tension key. Refer to page B-6)
Press “+” to increase the tension of the upper thread.
Using thread tension dial (For models equipped with
thread tension dial. Refer to page B-6)
Turn the thread tension dial to the right to increase
the tension of the upper thread.
Fabric is caught in the machine and cannot
be removed
If the fabric is caught in the machine and cannot be removed,
the thread may have become tangled under the needle plate.
Follow the procedure described below to remove the fabric
from the machine. If the operation could not be completed
according to the procedure, instead of attempting to complete
it forcefully, contact your nearest authorized Baby Lock
retailer.
Removing the fabric from the machine
a
Immediately stop the machine.
b
Turn off the machine.
c
Remove the needle.
If the needle is lowered into the fabric, turn the
handwheel away from you (clockwise) to raise the
needle out of the fabric, and then remove the needle.
Refer to “Replacing the needle” in the “Basic
operations” section.
d
Remove the presser foot and presser foot holder.
Refer to “Replacing the presser foot” and “Removing
and attaching the presser foot holder” in the “Basic
operations” section.
e
Lift up the fabric and cut the threads below it.
If the fabric can be removed, remove it. Continue with
the following steps to clean the race.
Note
If the upper threading and bobbin threading are
incorrect, the thread tension cannot be adjusted
correctly. Check the upper threading and bobbin
threading first, and then adjust the thread
tension.
Troubleshooting
A-8
f
Remove the needle plate cover.
1 Needle plate cover
Refer to “Cleaning the race” on page A-2.
g
Cut out the tangled threads, and then remove the
bobbin.
h
Remove the bobbin case.
If threads remain in the bobbin case, remove them.
1 Bobbin case
i
Use the cleaning brush or a vacuum cleaner to remove
any lint or dust from the race and its surrounding area.
1 Cleaning brush
2 Race
j
Use the included L-shaped (or disc-shaped)
screwdriver to loosen the two screws on the needle
plate.
k
Slightly lift up the needle plate, cut any tangled
threads, and then remove the needle plate.
Remove the fabric and threads from the needle plate.
If the fabric cannot be removed, even after completing
these steps, contact your nearest authorized Baby Lock
retailer.
l
Remove any threads in the race and around the feed
dogs.
m
Turn the handwheel to raise the feed dogs.
n
Align the two screw holes in the needle plate with the
two holes at the needle plate mounting base, and then
fit the needle plate onto the machine.
o
Lightly finger-tighten the screw on the right side of the
needle plate. Then, use the L-shaped (or disc-shaped)
screwdriver to firmly tighten the screw on the left side.
Finally, firmly tighten the screw on the right side.
If the fabric could be removed. Continue with step p.
If the fabric could not be removed. Continue with step j.
1
Note
Be careful not to drop the removed screws in the
machine.
Troubleshooting
Appendix A-9
MAINTENANCE AND TROUBLESHOOTING
A
Turn the handwheel to check that the feed dogs move
smoothly and do not contact the edges of the slots in the
needle plate.
1 Correct position of feed dogs
2 Incorrect position of feed dogs
p
Insert the bobbin case so that the S mark on the
bobbin case aligns with the
z mark on the machine.
Align the S and
z marks.
1 S mark
2
z mark
3 Bobbin case
Make sure that the indicated points are aligned
before installing the bobbin case.
q
Attach the needle plate cover according to step j in
“Cleaning the race” on page A-2.
r
Check the condition of the needle, and then install it.
If the needle is in a poor condition, for example, if it is
bent, be sure to install a new needle.
Refer to “Checking the needle” and “Replacing the
needle” in the “Basic operations” section.
Checking machine operations
If the needle plate has been removed, check machine
operations to confirm that installation has been completed
correctly.
a
Turn on the machine.
b
Select stitch .
c
Slowly turn the handwheel toward you
(counterclockwise), and look from all sides to check
that the needle falls at the center of the opening in the
needle plate.
If the needle contacts the needle plate, remove the
needle plate, and then install it again, starting with step
m in “Removing the fabric from the machine” on
page A-7.
1 Opening in the needle plate
2 Handwheel
Note
Be careful not to drop the removed screws in the
machine.
CAUTION
Never use a bobbin case that is scratched,
otherwise the upper thread may become
tangled, the needle may break or sewing
performance may suffer.
Make sure that you fit the bobbin case
properly, otherwise the needle may break.
a
b
b
a
CAUTION
Never use bent needles. Bent needles can
easily break, possibly resulting in injuries.
Note
After completing this procedure, continue with
the following procedure in “Checking machine
operations” to check that the machine is
operating correctly.
Memo
Since the needle may have been damaged when
the fabric was caught in the machine, we
recommend replacing it with a new one.
Note
Do not yet install the presser foot and thread.
Troubleshooting
A-10
d
Select stitch . At this time, increase the stitch length
and width to their maximum settings.
For details on changing the settings, refer to “Setting
the stitch width” and “Setting the stitch length” in the
“Basic operations” section.
e
Slowly turn the handwheel toward you
(counterclockwise) and check that the needle bar and
feed dogs operate correctly.
If the needle or feed dogs contact the needle plate, the
machine may be malfunctioning; therefore, contact
your nearest authorized Baby Lock retailer.
f
Turn off the machine, and then install the bobbin and
presser foot.
Refer to “Installing the bobbin” and “Replacing the
presser foot” in the “Basic operations” section.
g
Correctly thread the machine.
For details on threading the machine, refer to “Upper
Threading” in the “Basic operations” section.
h
Perform trial sewing with cotton fabric.
When the thread became tangled under the
bobbin winder seat
If the bobbin winding starts when the thread is not passed
under the pretension disk of the bobbin-winding thread guide
correctly, the thread may become tangled under the bobbin
winder seat.
In such a case, wind off the thread according to the following
procedure.
1 Thread
2 Bobbin winder seat
a
If the thread become tangled under the bobbin winder
seat, press the “Start/Stop” button once to stop the
bobbin winding.
When the foot controller is plugged in, remove your
foot from the foot controller.
b
Cut the thread with scissors beside the bobbin-winding
thread guide.
1 Bobbin-winding thread guide
c
Slide the bobbin winder shaft to the left, and then
remove the bobbin from the shaft and cut the thread
leading to the bobbin in order to be able to completely
remove the bobbin from shaft.
Memo
The thread may have become tangled as a result
of incorrect upper threading. Make sure that the
machine is correctly threaded.
Note
Incorrect sewing may be the result of incorrect
upper threading or sewing thin fabrics. If there
are poor results from the trial sewing, check the
upper threading or the type of fabric being used.
1
2
CAUTION
Do not remove the bobbin winder seat even if
the thread become tangled under the bobbin
winder seat. It may result in injuries.
Do not remove the screw on the bobbin
winder guide post, otherwise the machine may
be damaged; you cannot wind off the thread
by removing the screw.
1 Screw of the bobbin winder guide post
1
1
Troubleshooting
Appendix A-11
MAINTENANCE AND TROUBLESHOOTING
A
d
Hold the thread end with your left hand, and wind off
the thread clockwise with your right hand as shown
below.
e
Wind the bobbin again.
Note
Make sure that the thread passes under the
pretension disk of the bobbin-winding thread
guide correctly.
Troubleshooting
A-12
List of symptoms
Getting ready
Symptom Probable Cause Remedy Reference
Cannot thread the
needle.
Needle is not in the correct position.
Press the “Needle position” button to raise the
needle.
B-4
Needle is installed incorrectly. Reinstall the needle correctly. B-27
Needle is turned, bent or the point is dull. Replace the needle. B-27
Upper threading is incorrect.
Check the steps for threading the machine and
rethread the machine.
B-19
The needle threader hook is bent and does not
pass through the eye of the needle.
Contact your authorized Baby Lock retailer.
The needle threader lever cannot be moved or
returned to its original position.
Contact your authorized Baby Lock retailer.
A size 65/9 needle is being used.
The needle is incompatible with the needle
threader. Manually pass the thread through the
eye of the needle.
B-22
Cannot lower the
presser foot with
the presser foot
lever.
(For models
equipped with the
presser foot lifter
button)
Presser foot was raised using the “Presser foot
lifter” button.
Press the “Presser foot lifter” button to lower
the presser foot.
B-4
Bobbin thread
does not wind
neatly on the
bobbin.
The thread is not passed through the bobbin
winding thread guide correctly.
Correctly pass the thread through the bobbin
winding thread guide.
B-13
Bobbin spins slowly.
Move the sewing speed controller to the right
so that the speed will be increased.
B-13
The thread that was pulled out was not wound
onto the bobbin correctly.
Wind the thread that was pulled off around the
bobbin 5 or 6 times clockwise.
B-13
The empty bobbin was not set on the pin
properly.
Set the empty bobbin on the pin and slowly turn
the bobbin until you hear it click in place.
B-13
While winding the
bobbin, the bobbin
thread was wound
below the bobbin
winder seat.
You have not wound the bobbin thread properly.
While initially winding thread on the bobbin the
bobbin thread is not properly inserted into the
guides.
After removing the thread wound below the
bobbin winder seat, wind the bobbin correctly.
Follow the drawn images on the top of the
machine for guidance when threading the
machine for bobbin winding.
B-13, A-10
The bobbin thread
cannot be pulled
up.
Needle is turned, bent or the point is dull. Replace the needle. B-27
Bobbin is set incorrectly. Reset the bobbin correctly. B-16
Nothing appears in
the LCD.
Main power switch is not turned on. Turn the main power to ON. B-8
The plug of the power cord is not inserted into
an electrical outlet.
Insert the plug of the power cord into an
electrical outlet.
B-8
The brightness of the LCD is either too light or
too dark.
Adjust the brightness of the LCD. A-20
The LCD screen is
fogged up.
Condensation has formed on the LCD screen. After a while, the cloudiness will disappear.
The operation keys
do not respond.
A glove is worn when the keys are pressed.
The keys are pressed with a fingernail.
A non-electrostatic touch pen is being used.
Directly touch the operation keys with your
finger.
B-5
Troubleshooting
Appendix A-13
MAINTENANCE AND TROUBLESHOOTING
A
While sewing
The operation keys
do not respond, or
the sensitivity is
too strong.
The sensitivity of the operation keys is not set
for the user.
Adjust the sensitivity of the operation keys. B-12
The sewing light
does not come on.
The sewing light is damaged. Contact your authorized Baby Lock retailer.
(Light) is set to “OFF” in the settings
screen.
Change the setting to “ON”. B-10
Symptom Probable Cause Remedy Reference
Machine does not
operate.
“Start/Stop” button was not pressed. Press the “Start/Stop” button. B-33
The bobbin winder shaft is pushed to the right. Move the bobbin winder shaft to the left. B-13
There is no pattern selected. Select a pattern. B-32
Presser foot is not lowered. Lower the presser foot. B-33
“Start/Stop” button was pushed with the foot
controller attached.
Remove the foot controller, or use the foot
controller to operate the machine.
B-34
The “Start/Stop” button was pressed while the
machine is set for the sewing speed controller
to control the zigzag stitch width.
Use the foot controller instead of the “Start/
Stop” button to operate the machine, or set the
(Width control) to “OFF” in the settings
screen.
B-10
Needle breaks.
Needle is installed incorrectly. Reinstall the needle correctly. B-27
Needle clamp screw is not tightened. Tighten the needle clamp screw. B-27
Needle is turned or bent. Replace the needle. B-27
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
B-26
Wrong presser foot was used. Use the recommended presser foot. B-30
Upper thread tension is too tight. Adjust the thread tension setting. B-38
Fabric is pulled during sewing. Do not pull the fabric during sewing.
Spool cap is set incorrectly.
Check the method for attaching the spool cap,
then reattach the spool cap.
B-13
There are scratches around the opening in the
needle plate.
Replace the needle plate, or consult your
authorized Baby Lock retailer.
A-7
There are scratches around the opening in the
presser foot.
Replace the presser foot, or consult your
authorized Baby Lock retailer.
B-29
There are scratches on the bobbin case.
Replace the bobbin case, or consult your
authorized Baby Lock retailer.
A-2
Needle is defective. Replace the needle. B-27
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-13
Upper threading is incorrect.
Check the steps for threading the machine and
rethread the machine.
B-19
Bobbin is set incorrectly. Reset the bobbin thread correctly. B-16
Presser foot is attached incorrectly. Attach the presser foot correctly. B-29
Symptom Probable Cause Remedy Reference
Troubleshooting
A-14
Needle breaks.
Screw of the presser foot holder is loose. Securely tighten the screw of the presser foot. B-30
Fabric is too thick.
Use fabric that the needle can pierce when the
handwheel is turned.
B-26, S-4
Fabric is fed forcefully when sewing thick fabric
or thick seams.
Allow the fabric to be fed without being
forcefully pushed.
S-4
Stitch length is too short. Adjust the stitch length. B-37
Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-13
Upper thread
breaks.
Machine is not threaded correctly (used the
wrong spool cap, spool cap is loose, the thread
did not catch the needle bar threader, etc.)
Rethread the machine correctly. B-19
Knotted or tangled thread is being used. Remove any knots or tangles.
The selected needle is not appropriate for the
thread being used.
Select a needle that is appropriate for the type
of thread being used.
B-26
Upper thread tension is too tight. Adjust the thread tension. B-38
Thread is tangled.
Use scissors, etc., to cut the tangled thread and
remove it from the race, etc.
A-5
Needle is turned, bent or the point is dull. Replace the needle. B-27
Needle is installed incorrectly. Reinstall the needle correctly. B-27
There are scratches around the opening in the
needle plate.
Replace the needle plate, or consult your
authorized Baby Lock retailer.
A-7
There are scratches around the opening in the
presser foot.
Replace the presser foot, or consult your
authorized Baby Lock retailer.
B-29
There are scratches on the bobbin case.
Replace the bobbin case, or consult your
authorized Baby Lock retailer.
A-2
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
B-26
While sewing, the thread became knotted or
tangled.
Rethread upper and lower thread. B-13, B-19
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-13
The thread is
tangled on the
wrong side of the
fabric.
Upper threading is incorrect.
Check the steps for threading the machine and
rethread the machine.
Be sure that the presser foot is in the raised
position when threading the machine so that the
upper thread sets properly in the upper tension.
B-19, A-5
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
B-26
The upper thread is
too tight.
The bobbin thread is incorrectly installed. Correctly install the bobbin thread. B-16, A-4
Bobbin thread
breaks.
Bobbin is set incorrectly. Reset the bobbin correctly. B-16
Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-13
There are scratches on the bobbin or it doesn’t
rotate properly.
Replace the bobbin. B-16
Thread is tangled.
Use scissors, etc. to cut the tangled thread and
remove it from the race, etc.
A-7
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-13
Symptom Probable Cause Remedy Reference
Troubleshooting
Appendix A-15
MAINTENANCE AND TROUBLESHOOTING
A
Fabric puckers.
There is a mistake in the upper or bobbin
threading.
Check the steps for threading the machine and
rethread it correctly.
B-19
Spool cap is set incorrectly.
Check the method for attaching the spool cap,
then reattach the spool cap.
B-19
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle Combination”
chart.
B-26
Needle is turned, bent or the point is dull. Replace the needle. B-27
Stitches are too long when sewing thin fabrics. Shorten the stitch length. B-37
Thread tension is set incorrectly. Adjust the thread tension. B-38
Wrong presser foot. Use the correct presser foot. B-30
Skipped stitches
Machine is threaded incorrectly.
Check the steps for threading the machine and
rethread it correctly.
B-19
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle Combination”
chart.
B-26
Needle is turned, bent or the point is dull. Replace the needle. B-27
Needle is installed incorrectly. Reinstall the needle correctly. B-27
The needle is worn/damaged. Replace the needle. B-27
Dust or lint has collected under the needle
plate.
Remove the dust or lint with the brush. A-2
Thin or stretch fabrics are being sewn.
Sew with one sheet of thin paper under the
fabric.
S-4, D-3
No stitching
Needle is turned, bent or the point is dull. Replace the needle. B-27
Bobbin is set incorrectly. Reset the bobbin thread correctly. B-16
Upper threading is incorrect.
Check the steps for threading the machine and
rethread the machine.
B-19
High-pitched
sound while
sewing
Dust or lint is caught in the feed dogs. Remove the dust or lint. A-2
Pieces of thread are caught in the race. Clean the race. A-2
Upper threading is incorrect.
Check the steps for threading the machine and
rethread the machine.
B-19
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-13
There are needle holes or friction scratches in
the bobbin case.
Replace the bobbin case, or consult your
authorized Baby Lock retailer.
A-2
Fabric does not
feed through the
machine.
Feed dogs are set in the down position.
Slide the feed dog position switch to the right
.
B-2
Stitches are too close together. Lengthen the stitch length setting. B-37
Wrong presser foot was used. Use the correct presser foot. B-30
Needle is turned, bent or the point is dull. Replace the needle. B-27
Thread is entangled.
Cut the entangled thread and remove it from the
race.
A-7
Zigzag foot “J” is slanted on a thick seam at the
beginning of stitching.
Use the presser foot locking pin (black button
on the left side) on zigzag foot “J” to keep the
presser foot level while sewing.
S-4
Presser foot pressure is set incorrectly for
fabric.
Adjust the presser foot pressure
within the settings screen.
B-41
Symptom Probable Cause Remedy Reference
Troubleshooting
A-16
The fabric feeds in
the opposite
direction.
The feed mechanism is damaged. Contact your authorized Baby Lock retailer.
The needle
contacts the
needle plate.
The needle clamp screw is loose.
Firmly tighten the needle clamp screw. If the
needle is bent or blunt, replace it with a new
one.
B-27
Needle is turned, bent or the point is dull. Replace the needle. B-27
Fabric being sewn
with the machine
cannot be
removed.
Thread is tangled below the needle plate.
Lift up the fabric and cut the threads below it,
and clean the race.
A-7
A broken needle
has fallen into the
machine.
Turn off the machine, and then remove the
needle plate. If the needle that fell into the
machine can be seen, use tweezers to remove
it. After removing the needle, return the needle
plate to its original position and insert a new
needle.
Before turning on the machine, slowly turn the
handwheel toward you to check that it turns
smoothly and that the new needle enters
through the center of the needle plate opening.
If the handwheel does not turn smoothly or the
needle that fell into the machine cannot be
removed, contact your authorized Baby Lock
retailer.
A-7
The handwheel
feels sluggish
when it is turned.
Thread is tangled in the bobbin case.
Remove the tangled thread from the bobbin
case. Re-install the bobbin case so it is
correctly positioned.
A-5, A-7
The stitch is not
sewn correctly.
The presser foot that is used is not appropriate
for the type of stitch that you wish to sew.
Attach the presser foot that is appropriate for
the type of stitch that you wish to sew.
B-30
The thread tension is incorrect. Adjust the tension of the upper thread. B-38, A-6
The thread is tangled, for example, in the
bobbin case.
Remove the tangle thread. If the thread is
tangled in the bobbin case, clean the race.
A-7
Feed dogs are set in the down position.
Slide the feed dog position switch to the right
.
B-2
Symptom Probable Cause Remedy Reference
Troubleshooting
Appendix A-17
MAINTENANCE AND TROUBLESHOOTING
A
After sewing
Error messages
If the “Start/Stop” button is pressed before the machine is correctly set up or if an operation is performed incorrectly, an error
message appears in the LCD. Follow the instructions that appear. The message will disappear if or is pressed while the
message is displayed.
Symptom Probable Cause Remedy Reference
Thread tension is
incorrect.
Upper threading is incorrect.
Check the steps for threading the machine and
rethread the machine.
B-19
Bobbin is set incorrectly.
Reset the bobbin. (If needle plate was removed,
reinstall needle plate and tighten screws prior to
installing bobbin case. Check to make sure
needle enter through the center of needle plate
opening.)
B-16, A-2
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
B-26
Presser foot holder is not attached correctly. Reattach the presser foot holder correctly. B-30
Thread tension is set incorrectly. Adjust the thread tension. B-38, A-6
Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-13
Needle is turned, bent or the point is dull. Replace the needle. B-27
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-13
Character or
decorative patterns
are misaligned.
Pattern adjustment settings were set incorrectly. Revise the pattern adjustment settings. D-10
Pattern does not
turn out.
Wrong presser foot was used. Attach the correct presser foot. B-30
Did not use a stabilizer material on thin fabrics
or stretch fabrics.
Attach a stabilizer material. S-4, D-3
Thread tension is set incorrectly. Adjust the thread tension. B-38, A-6
Fabric was pulled, pushed or fed at an angle
while it was being sewn.
Sew while guiding the fabric with your hands so
that the fabric is fed in a straight line.
B-33
The thread is tangled, for example, in the
bobbin case.
Remove the tangle thread. If the thread is
tangled in the bobbin case, clean the race.
A-7
Error Messages Cause/Solution
1
This message is displayed when the needle plate cover is not attached when the
machine is turned on.
2
This message is displayed when the sewing speed controller is set to control the
zigzag stitch width, and the “Start/Stop” button is pressed. Set (Width control)
to “OFF” (refer to page B-10), or use the foot controller to operate the machine.
Troubleshooting
A-18
3
This message is displayed when (Twin needle) is set to “ON”, and a stitch pattern
that cannot be sewn with the twin needle is selected.
4
This message is displayed when the “Start/Stop” button was pressed while the foot
controller was connected.
5
This message is displayed when the buttonhole lever is down, a stitch other than a
buttonhole is selected, and a button, such as the “Start/Stop” button, is pressed.
6
This message is displayed when the buttonhole lever is up, a buttonhole stitch is
selected, and a button, such as the “Start/Stop” button, is pressed.
7
This message is displayed when a button, such as the “Start/Stop” button, was
pressed while the presser foot was raised.
8
This message is displayed when you tried to combine more than 70 decorative
stitches.
9 This message is displayed when the stitch mode was changed.
10 This message is displayed when you tried to delete a saved pattern.
11
This message is displayed when a button, such as the Reverse/reinforcement stitch
button, was pressed while the bobbin winder shaft is moved to the right.
Error Messages Cause/Solution
Troubleshooting
Appendix A-19
MAINTENANCE AND TROUBLESHOOTING
A
12
This message is displayed when a button, such as the “Start/Stop” button, was
pressed after a stitch has been deleted.
13
This message is displayed when the motor locks due to tangled thread or for other
reasons related to thread delivery.
14
This message is displayed when you try to sew with a stitch other than a straight
stitch (middle needle position) while the straight stitch needle plate is installed.
This message is also displayed when the needle plate is removed while the machine
is still turned on.
15 F**
If error message “F**” appears in the LCD while the machine is being used, the
machine may be malfunctioning.
Contact your nearest authorized Baby Lock retailer.
Error Messages Cause/Solution
Specifications
A-20
Operation beep
Each time a key is pressed you will hear one beep. If an
incorrect operation is performed you will hear two or four
beeps.
If a key is pressed (correct operation)
One beep sounds.
If an incorrect operation is performed
Two or four beeps sound.
If the machine locks up, for example, because
the thread is tangled
The machine beeps for four seconds and the machine
automatically stops.
Be sure to check for the cause of the error and correct it
before continuing to sew.
Canceling the operation beep
a
Select (Buzzer) in the settings screen and set it to
“OFF”.
Nothing appears in the LCD
If nothing appears in the LCD when the machine is turned on,
the brightness of the LCD is either too light or too dark. If this
is the case, perform the following operation.
a
Turn off the machine.
b
While pressing (Reinforcement stitch button) on
the operation panel, turn on the sewing machine.
c
Press the “-” or “+” key.
Adjust the brightness of the LCD so that the screens can
be seen.
d
Turn off the machine, then turn it on again.
* Please be aware that some specifications may change without notice.
Specifications
Item Specification
Dimensions of machine Approx. 480 mm (W) x 300 mm (H) x 249.4 mm (D)
(Approx. 18-7/8 inches (W) x 11-7/8 inches (H) x 9-7/8 inches (D))
Weight of machine Approx. 9.7 kg (Approx. 21.3 lb)
Sewing speed 70 to 850 stitches per minute
Needles Home sewing machine needles (HA × 130)
Index
Appendix A-21
MAINTENANCE AND TROUBLESHOOTING
A
Numerics
1/4" quilting foot ....................................................................... S-28
1/4" quilting foot with guide
..................................................... S-28
7 mm satin stitches
.................................................................... D-2
A
Accessories
included accessories
............................................................... B-6
Accessory compartment
............................................................. B-5
Adjustable zipper/piping foot
.................................................... S-23
Adjusting stitch length
.............................................................. B-37
Adjusting stitch width
............................................................... B-37
Adjusting thread tension
........................................................... B-38
Air vent
...................................................................................... B-2
Appliqué
.................................................................................. S-26
Attaching presser foot holder
.................................................... B-30
Automatic fabric sensor system
................................................. B-41
Automatic reinforcement stitch key
.......................................... B-35
Automatic thread cutting
.......................................................... B-40
B
Ball point needle ...................................................................... B-26
Bar tack stitch
........................................................................... S-35
Basic sewing
................................................................... B-31, D-4
Basic stitching
............................................................................ S-6
Basting stitch
.............................................................................. S-6
Beep
......................................................................................... A-20
Blind hem stitch
......................................................................... S-8
Bobbin case
................................................................................ B-3
bobbin case removal
.............................................................. A-2
Bobbin cover
................................................................... B-3, B-16
Bobbin installation
................................................................... B-16
Bobbin thread
pulling up
............................................................................. B-22
winding
................................................................................ B-13
Bobbin winder
............................................................................ B-2
Bobbin winding
........................................................................ B-13
Bobbin winding thread guide
.......................................... B-2, B-13
Button guide plate
.................................................................... S-15
Button sewing
........................................................................... S-17
Buttonhole lever
.............................................................. B-3, S-15
Buttonhole sewing
.................................................................... S-14
Buttonhole stitching
.................................................................. S-14
Buzzer
...................................................................................... A-20
C
Changing sewing direction ......................................................... S-2
Character spacing
...................................................................... D-7
Character stitches
........................................................... B-32, D-2
Checking needle
....................................................................... B-27
Cleaning
cleaning machine surface
....................................................... A-2
LCD screen
............................................................................. A-2
race
........................................................................................ A-2
Combining patterns
................................................................... D-5
Concealed seams
...................................................................... S-19
Crazy quilt stitching
.................................................................. S-27
Cross stitch stitches
.................................................................... D-2
Curve sewing
.............................................................................. S-2
Cutting thread automatically
..................................................... B-40
Cylindrical pieces
....................................................................... S-2
D
Darning .................................................................................... S-36
Darning stitch
........................................................................... S-35
Decorative stitches & patterns
.................................................... D-2
Drawnwork
............................................................................... S-44
E
Error messages ......................................................................... A-17
Even seam allowance
.................................................................. S-3
Eyelet stitching
.......................................................................... S-38
F
Fagoting .................................................................................... S-41
Feed dog position switch
........................................................... B-2
Feed dogs
.................................................................................. B-3
Flat bed attachment
.......................................................... B-2, B-5
Foot controller
................................................................ B-2, B-34
Foot controller jack
......................................................... B-2, B-34
Fraying, preventing
................................................................... S-11
Free motion mode
.................................................................... B-42
Free motion quilting
.................................................................. S-30
free motion echo quilting foot “E”
......................................... S-32
free motion open toe quilting foot “O”
.................................. S-30
free motion quilting foot “C”
................................................. S-31
Front view
.................................................................................. B-2
H
Handle ....................................................................................... B-2
Handwheel
................................................................................ B-2
Heirloom stitching
.................................................................... S-44
Horizontal spool pin
................................................................ B-23
Horizontal stitching
.................................................................. S-39
I
Inserting a piping ...................................................................... S-24
Installing bobbin
...................................................................... B-16
J
Joining ...................................................................................... S-43
K
Knee lifter ................................................................................ B-43
Knee lifter mounting slot
................................................. B-2, B-43
L
LCD
nothing appears
................................................................... A-20
LCD messages
.......................................................................... A-17
LCD operation
........................................................................... B-9
LCD screen
cleaning
................................................................................. A-2
Leather/vinyl fabrics
.................................................................... S-5
M
Machine surface cleaning .......................................................... A-2
Main power switch
........................................................... B-2, B-8
Maintenance
.............................................................................. A-2
Manual needle threading
......................................................... B-22
Mirroring
........................................................................ B-40, D-8
Mirroring stitches
..................................................................... B-40
Index
Index
A-22
N
Needle
condition
............................................................................. B-27
position
................................................................................... S-7
replacement
......................................................................... B-27
threading
.............................................................................. B-21
types, sizes & uses
................................................................ B-26
Needle bar thread guide
............................................................ B-3
Needle plate
.............................................................................. B-3
Needle plate cover
..................................................................... B-3
Needle plate marking
.................................................................. S-3
Needle position button
.............................................................. B-4
Needle threader
....................................................................... B-21
Needle threader lever
..................................................... B-2, B-21
Non stick foot
............................................................................. S-5
O
Operation beep ........................................................................ A-20
Operation buttons
...................................................................... B-4
Operation keys
.......................................................................... B-4
Operation panel
................................................................ B-2, B-4
Operation problems
................................................................... A-4
Overcasting stitches
....................................................... S-11, S-12
P
Pant legs ..................................................................................... S-2
Parallel stitches
........................................................................ B-23
Part names & functions
.............................................................. B-2
Patchwork
...................................................................... S-26, S-27
Pattern
check
..................................................................................... D-6
combination
........................................................................... D-5
density
................................................................................... D-6
length
..................................................................................... D-7
mirroring
................................................................................ D-8
realighnment
........................................................................ D-10
recalling
............................................................................... D-10
repetition
............................................................................... D-5
size
........................................................................................ D-6
storage
................................................................................... D-9
Piecing
...................................................................................... S-27
Piping inserting
......................................................................... S-24
Pivoting
................................................................................... B-41
Power supply jack
............................................................. B-2, B-8
Power switch
.................................................................... B-2, B-8
Presser foot
pressure
............................................................................... B-41
replacement
......................................................................... B-29
types
.................................................................................... B-44
Presser foot holder
installation
........................................................................... B-30
removal
................................................................................ B-30
Presser foot holder screw
........................................................... B-3
Presser foot lever
........................................................................ B-2
Presser foot lifter button
............................................................. B-4
Pretension disk
..................................................... B-2, B-15, A-10
Q
Quilting .................................................................................... S-29
Quilting guide
........................................................................... S-30
R
Race .......................................................................................... A-2
Realigning pattern
.................................................................... D-10
Recalling pattern
...................................................................... D-10
Reinforcement stitch button
............................................ B-4, B-35
Reinforcement stitching
............................................................ S-35
Removing presser foot holder
................................................... B-30
Repeating patterns
..................................................................... D-5
Replacing needle
...................................................................... B-27
Replacing presser foot
.............................................................. B-29
Reverse stitch button
....................................................... B-4, B-35
Reverse/Reinforcement stitches
................................................ B-35
S
Satin stitch length, changing ...................................................... D-7
Satin stitches
............................................................................. D-2
Satin stitching
........................................................................... S-34
Saving stitch settings
................................................................. B-39
Scallop stitching
....................................................................... S-42
Seam allowance, even
................................................................ S-3
Seam ripper
.............................................................................. S-16
Settings
automatic reinforcement stitching
......................................... B-35
display language
................................................................... B-12
input sensitivity
.................................................................... B-12
Settings screen
.......................................................................... B-10
Sewing basics
........................................................................... B-31
Sewing direction change
............................................................ S-2
Sewing speed controller
.................................................. B-4, S-34
Shell tuck stitch
........................................................................ S-43
Side cutter
................................................................................ S-12
Size
........................................................................................... D-6
Smocking
................................................................................. S-42
Solving operation problems
........................................................ A-4
Spool cap
........................................................................ B-2, B-14
Spool net
.................................................................................. B-14
Spool pin
.............................................................. B-2, B-13, B-19
“Start/Stop” button
...................................................................... B-4
Step stitch pattern
...................................................................... D-7
Stippling
................................................................................... S-26
Stitch guide foot
......................................................................... S-3
Stitch length adjustment
........................................................... B-37
Stitch selection
......................................................................... B-32
Stitch settings
........................................................................... B-44
Stitch types
............................................................................... B-31
Stitch width adjustment
............................................................ B-37
Storing patterns
......................................................................... D-9
Straight stitch
......................................................... S-6, S-19, S-27
Stretch fabrics
............................................................................. S-5
T
Thick fabrics ............................................................................... S-4
Thin fabrics
................................................................................ S-4
Thread cutter
................................................................... B-2, B-34
Thread cutter button
................................................................... B-4
Thread cutting, automatic
......................................................... B-40
Thread guide plate
..................................................................... B-2
Thread tension adjustment
....................................................... B-38
Thread tension dial
................................................. B-2, B-38, A-7
Threading
threading needle
................................................................... B-21
threading needle manually
................................................... B-22
upper threading
.................................................................... B-19
Tips
............................................................................................ S-2
Top cover
................................................................................... B-2
Trial sewing
................................................................................ S-2
Triple stretch stitch
........................................................... S-6, S-35
Troubleshooting
......................................................................... A-4
Twin needle
............................................................................. B-23
U
Upper thread ............................................................................ B-19
Upper thread tension
....................................................... B-38, A-6
Utility stitches
............................................................... B-32, B-44
W
Winding bobbin ....................................................................... B-13
Wing needle
............................................................................. S-44
Index
Appendix A-23
MAINTENANCE AND TROUBLESHOOTING
A
Z
Zigzag stitches ............................................................... S-12, S-26
Zigzag width adjustment
.......................................................... B-37
Zipper insertion
centered
.................................................................... S-19, S-23
side
....................................................................................... S-20
English
888-F51/F61/F71
Printed in Vietnam
XG0017-201
2
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Baby Lock Soprano - BLMSP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Baby Lock Soprano - BLMSP in de taal/talen: Engels als bijlage per email.

De handleiding is 8,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info