----
----
----
P
Used to make and
receive calls.
Lets you redial the
last number you
called.
Lets you lock
(and unlock)
the key pad to
prevent accidentally
pressing buttons.
To access your
phone’s functions.
To store numbers
in the memory.
Set
Key lock
Redial
Handset button
2
Verve 100 – Edition 5 – 18.8.00 – 3250
Safety information
General
Only use the power supply included with the product. Using an
unauthorised power supply will invalidate your warranty and may
damage the telephone.
Ensure that the battery is fitted correctly. The red wire should be
connected to the positive terminal (+) and the black wire to the
negative terminal (–). Approved battery type 1a (300mAh)
V30145-K1310-X147 NiCd.
Replacement batteries can be obtained via the BT Helpline on
0845 790 8070.
If the key lock is active, it is not possible to make emergency calls
to 999 and 112.
Do not open the handset or base station. This could expose you to
high voltages or other risks. Contact the Helpline for repairs.
Radio signals transmitted between the handset and base may cause
interference to hearing aids.
This product should not be used near emergency/ intensive
care medical equipment and should not be used by people with
pacemakers.
Never dispose of batteries in a fire. There is a serious risk of
explosion and/or the release of highly toxic chemicals.
Do not hold the handset to your ear during the incoming ring tone.
Environmental
Do not expose to direct sunlight.
The product may heat up when the batteries are being recharged.
This is normal. However, it is recommended that you do not place
the product on antique/veneered wood to avoid damage.
Do not stand your product on carpets or other surfaces which
generate fibres, or place it in locations preventing free flow of air
over its surfaces.
Do not submerge any part of your product in water and do not use
it in damp or humid conditions, such as bathrooms.
Do not expose your product to fire, explosive or other hazardous
conditions.
There is a slight chance that your phone could be damaged by an
electrical storm. We recommend that you unplug the power and
telephone line cord for the duration of the storm.
Cleaning
Simply clean the handset and base station with a damp (not wet)
cloth, or an antistatic wipe. Never use household polish as this will
damage the product. Never use a dry cloth as this may cause a
static shock.
3
Verve 100 – Edition 5 – 18.8.00 – 3250
Setting Up
Plan the location
Situate your product close enough to the telephone socket
and mains power supply so that the cables will reach.
Make sure it is at least 1 metre away from other electrical
products to avoid interference.
Note
The range of your handset is 30m indoors and
approximately 200m outdoors. If the icon flashes on the
display you could be out of range and should move closer to
the base station.
1 Connect the power cable
Plug the power cable into the power socket on the underside
of your Verve 100.
4
Verve 100 – Edition 5 – 18.8.00 – 3250
WARNING
Do not connect the telephone line cord to the phone socket
until the handset is fully charged. This will prevent the risk
of the phone being answered before the battery is charged.
4 Charge the handset batteries for at
least 16 hours
Place the handset on the base and charge for at least 16 hours
without interruption.
3 Install the rechargeable battery pack
in the handset
Insert the battery connector as shown in the diagram. Place
the battery pack in the battery compartment and insert the
battery cable in the clip provided. Put the battery compartment
cover back into place and click shut.
To open the battery cover. Push tab downwards and pull.
The cover clicks off.
2 Plug the power adaptor into a mains
power socket and switch on
Battery performance
After charging your Verve 100 for the first time, subsequent
charging time is approximately 4-5 hours. Batteries and
case may become warm during charging. This is normal
and is not dangerous.
Note
If you experience any difficulties setting up or using your
phone, call the BT Helpline on 08457 908070.
5
Verve 100 – Edition 5 – 18.8.00 – 3250
5 Connect the telephone line cord to
the base station
Ensure that this is fitted correctly into the right socket.
(See the diagram on page 3).
Note
Under ideal conditions, the handset should give about 10
hours talktime or 100 hours standby on a single charge.
However, new NiCad batteries do not reach their full
capacity until they have been in normal use for several days.
Please note that the lifespan of NiCad rechargeable
batteries depends on how heavily they are used. However,
over time, their capacity to recharge will begin to diminish
and they will eventually need replacing.
6 Plug your Verve 100 into the phone
socket
7 Register your handset to the base
Unplug the power adaptor. Ensure that the handset is on the
base. The icon will flash on the display. Plug the power
adaptor back into the mains power socket. After
approximately 90 seconds the icon will stop flashing.
The handset is now registered.
Please remove the protective film from the display on the
handset.
You must register your handset to the
base before you can make any calls.
! !
6
Verve 100 – Edition 5 – 18.8.00 – 3250
To redial the last number
Press the REDIAL button. The display will show
the last number dialled.
Press the HANDSET button. The number is
dialled.
Using your Verve 100
To make an external call
Enter the telephone number, check that it is correct,
and then press the HANDSET button to dial.
You will hear the number dialling and the
icon will appear on the display.
Or
Press the HANDSET button. You will hear the dial
tone.
Dial the telephone number you require. The
number is dialled and will be shown on the display.
To receive an external call
When the phone rings, pick up the handset, press
the HANDSET button and speak.
To end a call
Press the HANDSET button. The icon will
disappear from the display.
Or
Place the handset back on the base station.
